Corner for gypsum board: how to make metal from profile, perforated finish, inner plastic

Beautiful box of drywall in the bathroom is original to decorate the interior and hide communication To properly make the angle of the drywall, you must have some experience or take advantage of the advice of friends who have worked with this material. Yes, drywall is a versatile material, but made some awkward movements during installation, it can break down and come to the uselessness, and this means that it is also fragile. Especially when choosing a method of mounting gipsokartonnyh sheets resort to various types of fasteners, starting with screws, ending with large anchor bolts, which can damage the sheets. The corners of plasterboard are fastened from two sides, from the inner and the outer side of the right angle and produce it using corners from the metal profile.

angle of plasterboard: where to start to do

When decorating the room in the house, often face irregularities of the walls, creating angular design, putty holes and gaps in the wall. In this case, drywall sheets will help, in particular, you can make right angles of 90 degrees from them and even give it different shapes.

Plasterboard sheets are sufficiently plastic, so they allow you to make a box of any shape

For mounting angles of plasterboard in any master must present the necessary tools and accessories:

• drilling machine( drill, hammer orScrewdriver);
• Screwdrivers for screwdrivers( bits);
• Plasterboard boards;
• Shears for metal cutting and knife for cutting gypsum board;
• Screws or screws of various diameters;
• Measuring instrument( measuring tape, level, marker, gon);
• Bulgarian.

This set is quite enough for both experienced and novice master.

In order to fix everything correctly, it is necessary to have reinforced profiles, spatulas, trowels, a primer and a putty for walls.

Such materials can be easily purchased in building stores.

How to make the angle of the drywall

Before starting finishing work is necessary to use personal protective equipment: gloves and goggles to protect hands and organs of vision. This will prevent injuries during work, for example, when cutting gipsokartonnyh sheets.

By the way, to make gypsum plasterboard corners, the wall must be plastered in advance.

This will eliminate the unevenness of the wall and facilitate further work, the walls must be pre-formed with a frame, on which the plasterboard plates will be based.

The instructions for creating interior corners from plasterboard are simple and do not require a lot of knowledge:

1. First, you need to draw a line on the floor where you will have to install a metal profile that will be the "foundation" of the future wall. For a correct and accurate location, use the building level and the corner.
2. On the ceiling, you also need to make a line on which the metal profile will be located.
3. After this, you can proceed with the installation of guide profiles installed vertically, perpendicular to the floor. The interval between profiles will be approximately 30-40 centimeters, and for fixing, use dowels with self-tapping screws.
4. The penultimate stage of creating an internal corner from gypsum board is the connection of the frame to the wall, which will increase the strength of the wall. The fixing is done by self-tapping screws for gypsum board.
5. The final stage is the embedding of the frame with plasterboard. To ensure that the corners of the sheets are not damaged and do not break, you need to cut and chamfer on the plasterboard at an angle of 45 degrees, using a Bulgarian, or an electric jigsaw.

Before starting the repair work on the installation of the box, you should first make measurements on the ceiling and on the wall

It is necessary to try to maximize the parallel installation of the profile both on the floor and on the ceiling so that the walls are straight.

To strengthen the structure of the frame, the installation of reinforced, galvanized double profile will help.

The internal angle assumes the main load, therefore, the angle can be strengthened with the help of additionally installed self-tapping screws. After the end of the installation, plaster the joints and plaster the corners.

The outer corner is made as follows:

1. The first thing you need to do when marking the outer corners is marking, where perforated metal or plastic corners will be installed, and also measure and cut off the desired length.
2. Look and check that the corners of the profile are flat over the entire length, this can be done using a level or a corner.
3. Secure the corner with self-tapping screws and install it vertically, namely perpendicular to the floor;
4. The final stage is the fixation of profiles with glue on a gypsum base. Lubricate the perforation holes of the corner with glue using a spatula with a thick layer.

After drying, unscrew the retaining screws, plaster the holes and work the surface with a grinding wheel or sandpaper.

Corner for plasterboard

As experience shows, it is possible to use both wooden corners and metal ones. However, the first has some disadvantages.

They are:

• It is necessary to treat with an antiseptic solution in order to prevent mold and wood pests;
• Wood absorbs moisture, which affects the shape and durability of the structure;
• Unlike metal, which can be given absolutely any shape, the tree can not be bent.

The most popular and demanded are the metal corners for gypsum board

Along with the shortcomings of wood, the advantages of metal are considerable.

To accurately determine which profile to choose wooden or metal, you need to proceed from the budget for repairs, if it is small, it is enough to limit the wooden profile or better to combine them with metal, which would be a more reasonable option.

Among them are:

• Flexibility and flexibility( you can attach any shape by making an incision on the side faces of the profile);
• No additional treatment is required from rust and flowering( the entire surface is galvanized);
• Increased strength;
• There are many examples of using metal instead of wood.

Therefore, in finishing works, almost always used only metal corners.

How to make a corner from the profile for drywall

The angle for gypsum board should be used metal, but in order to make it it is necessary to make precise measurements of the profile sizes and be able to understand their kinds.

To achieve the right angle of the wall from gypsum board, you must first make an angle from the profile. To do this, we need a guide profile that we installed on the floor, a ceiling profile that is fixed to the ceiling and parallel to the rail, and a rack-mount profile designed to create the framework and faces of the future corner.

Correctly selected metal corners for gypsum cardboard will make the construction of a gypsum board strong and reliable

Note: The rack profile can be replaced by a narrow beam, but it all depends on the profiles fixed on the floor.

If the width of the guide profile is equal to the height of the narrow profile, then a less expensive option is used.

To make an angle from the profile for gypsum board, use the following instruction:

1. Check the parallelism of the guide and ceiling profiles of the first and second walls and that they are also straight;
2. Install the rack profile on the end of the guide so that the face of one of the corners is formed, repeat the operations for the second wall;
3. For fixing the racks, special retention brackets are used, fastened to self-tapping screws;

That's the whole instruction, and even if it seems to you that this is impossible, it's worth trying and everything will turn out.

How to make a corner for drywall( video)

The wall covering of gypsum boards is a very popular finishing solution nowadays, as this material is universal in use, has soundproof properties, and also is cheap in the construction market.