How to whitewash the ceiling with water-based paint without divorce: whitewash with your own hands, paint over the whitewash, video

latex paint - a widespread and popular material for finishing the ceiling latex paint differs in that is not afraid of water. In this sense, it is more difficult to find something in this price segment. The water emulsion works so: it lies on the surface, the water molecules evaporate very quickly, and the polymer layer solidifies. This painting is also beneficial because the water-based composition dries quickly, the paint does not exfoliate, and does not emit an odor.

Whitewashing the ceiling latex paint with their hands: how to start

Make sure this is the same kind of coverage that you need. Water-based paints have the following advantages: high strength, durability, ability to make local ceiling repairs, easy maintenance.

You can choose matte or glossy paint, acrylic or latex.

Before you begin to whitewash the ceiling latex paint, you must thoroughly clean the ceiling covering

Preparatory work

• Remove the old layer of finishing the ceiling - the traces of old paint or whitewash, as well as stains. If the repair was a long time, it would be correct to knock down all the old plaster.
• After removing the so-called "weaknesses", re-plaster the surface - this is necessary for deep leveling.
• The puttying is done by finishing alignment, it is done in two or more stages, only at least two layers. Each layer needs to be allowed to dry thoroughly, therefore the difference between each putty layer is not less than 24 hours.
• Next, sand the surface. In connection with these, it will become smooth, which will allow to paint it, avoiding divorce. A special grater is used, sanding is carried out in circular motions.

After surface preparation, it will not be difficult to paint. Smooth, clean, smooth - that's how the ceiling should be before whitewashing.

Preparation and painting the ceiling latex paint( video)

Gun for whitewashing the ceiling: what should be

you can take a manual spray gun - is the easiest of the devices of this type, and work with them will not be quick. Used more often pneumatic spray gun, which as an impact takes compressed air, and it is forced by compressors. As a result - a uniform coverage, and the speed of work is different.

If the price question you are not so constrained, you can buy an electric gun - it's fast, simple, and effective. The scheme is as follows: from the barrel under the sight of the pump comes a solution for application, it forms a trickle, and then fires through the nozzle.

The spray gun will greatly simplify and accelerate the painting process of the

tools, although small, but equipped with well-adjustable nozzles and instruments to control the flow rate of the composition, as well as spraying speed.

How to paint the ceiling from the spray gun correctly

First you have to prepare the solution itself. The solution should not be viscous or thick so as not to clog the system. That is, prepare the staff, mixing it all the time. If you need a large amount of paint or whitewash, a construction mixer is used.

Even alternative modern methods of ceiling decoration do not cancel whitewash with paint as a classic way of repair.

In order not to clog the spray gun system, it is important to correctly prepare the paint solution( whitewash)

Step-by-step instructions:

• Preparing the pump. Inside the tank, pour a half-liter of whitewash, while the locking mechanism must be closed. Get the suction hose from the whitewash, pump the pump further. Double the stroke of the rod make 15 times, then lower the sleeve into the solution and swing to create working pressure.
• Regulation of spraying. Adjust the spot that will be obtained by spraying. Do this, for example, on a piece of old wallpaper.
• Painting. Painting and whitening is necessary, making sure all conditions are met - the temperature is not lower than 15 degrees, and the humidity is above 55%.We need to whiten from some angle, the first layer must be dense, then it needs to dry thoroughly, and the second one will already be thin, matting.

Work strictly in a respirator, gloves and goggles.

How to paint the ceiling with water-based paint on the whitewash: instruction

To begin with, it is not desirable to paint over the whitewash. Theoretically, it can be done, and so many do, but only if the whitewash layer is thin and durable. And if you paint, washing and sweeping the bleached layer, you will get a little aesthetic spectacle.

Surface preparation: Surface preparation:

• Coat the surface with a good deep penetration primer;
• Allow the primer to dry thoroughly, then make the test - slightly scratch the surface, if it is easily destroyed, it is better not to paint it( in this situation, you need to remove the chalk layer);
• But when painting with water-based paint, it is possible not to ground the surface, the paint itself is a priming solution.

If the whitewash layer is strong, the paint will hold well and firmly.

How correctly to whitewash the ceiling with water-based paint( video)

You can paint the ceiling over the whitewash only if the whitewash layer is not thick, and not strong enough. If you are going to use enamel or oil paint, then it is better not to apply it over the whitewash - the chalk layer in this case will have to be removed.

Good repair!