In order to remove all the dirt from the linen and it has found freshness and purity, it is necessary to wash it in warm or hot water - every housewife knows this. Fortunately, the times when the water for washing had to be boiled in huge metal pots had long ago been left behind. Today it heats the water, washing and pressing the laundry is our irreplaceable assistant - a washing machine.
However, sometimes, as a result of any malfunctions, the unit suddenly "refuses" to heat the water. With what this problem can be connected, and how to deal with it read below.
How to understand that the washing machine does not heat water when washing?
It would seem that the most obvious way to determine at what temperature the laundry is being washed is to touch things immediately after the machine completes the washing cycle. But this is not entirely correct, since in most cases freshly washed clothes will be cold. The fact that the washing machine heats the water only directly for washing, and the rinsing of the laundry takes place in cold water.
A more accurate method is to determine the water temperature through the hatch door. Start the washing program and, about 30 minutes after its start, touch the door. If the glass is cold, then the heating does not occur.
Reasons for
Washing machines from the most sought-after manufacturers, such as LG, Samsung, Bosch, Zanussi, Atlant, Indesit, Ardo, usually stop heating water for one of the following reasons:
| What is the source of the | problem? | What should I do? |
| Incorrect choice of the washing mode | The machine does not heat water only with certain washing programs. | All modern models of washing machines have several programmed wash modes for different types of fabrics. Some materials can be washed only in cold water. Carefully study the instruction manual: it is possible that for the mode you have chosen, water heating is not provided for |
| Incorrect connection of the washing machine | The machine constantly picks up and drains the water. | If you connected the equipment to communications without the help of a professional, you could easily connect the drainage hoses and water set to othersreleases. Disconnect the hoses and connect in accordance with the instructions;if necessary, call the master |
| Breakdown of the thermostat | The temperature sensor removed from the washing machine shows the same resistance in the cooled and heated state. | The resistance of the thermostat can be checked with a multimeter, to be heated under hot water;if the readings do not differ, the sensor must be replaced with a new |
| . Faulty tubular heating element | . On the TEN body, it is possible to detect mechanical damage or a thick layer of plaque;it is also possible to damage the wires connected to it. | The TEN serviceability can be checked by measuring the resistance with a tester. If the reading of the device does not correspond to the norm, you should purchase a new heater( which values are considered normal, can be found in the special literature). |
| The | software module has problems. The connection is made as expected, the correct washing program has been selected, all elements are in good order, but the water still does not heat up. | The programmer may fail for various reasons, for example, as a result of a power surge. The problem is solved by flashing it or resetting the settings to the original |
. What should I do if the washing machine is too hot for water?
It happens that the water in the washing machine heats up, but very slowly, so that, after a rather long time after the start of washing, the glass of the hatch door still remains cold. This, insignificant, at first glance, problem can lead to serious enough trouble. Poorly washed laundry is annoying, but this is not all: as a result of slow heating, there may be a breakdown of the TEN or the programmer.
Most often, the reason for this strange "behavior" of the washing machine is the formation of a thick layer of scale on the heater tubes. To get rid of the plaque, it is recommended to start the washing and rinsing program with an empty tank, filling two tablespoons of citric acid instead of the washing powder( washing should be performed at maximum water temperature).
Tips for the
- If your washing machine has been in operation for more than 7 years, most likely, most of the problems in its operation are due to TEN.The quality of tap water we have left much to be desired, so the service life of the heater is markedly reduced. Experts advise to replace this element as soon as the first problems appear.
- Modern models of washing machines are equipped with the function of forced water heating( how to start it, read in your user manual).If the thermostat malfunctions, this function will help some time to do without replacing the water temperature sensor.
- One of the indicators that the stylalka does not heat water is the musty smell of washed clothes. It does not always appear, but if you notice it, you first need to test the heater for serviceability.
- In order to prolong the service life of the tubular heating element( after all, it is often the water heating faults associated with it), it is necessary to use only high-quality detergent powders and not to exceed the dosage of detergents and caring agents. If you are concerned about the quality of tap water, install a flow filter to reduce the level of hardness.
