Roofing materials for the roof: the types and prices of coatings

Combining in the decoration of the roof Ondulin, shingles and polymer membrane roofing

To make the right choice when purchasing roofing material you must first determine the purpose of the building. The range of modern roofing materials is quite extensive and includes the following varieties:

• seamed;
• piece;
• sheet;
• leveling (mastic);
• soft.

Note!Each of these types of roofing combines several subspecies. As the market offers a wide range of coatings, the grouping makes it easier to navigate the range and to select products for construction work.

Ceramic tile refers to the piece roofing materaly

Sheet metal roofing materials for the roof: types and prices

metalAs one of the most popular types of roof, it has many beneficial advantages. She is beautiful, provides the highest strength, although its operation is accompanied by a certain noise level. This type of coating is made based on the steel sheet. The feedstock may have different, up to 0.5 mm thick.

The surface of the finished articles covered with a lacquered composition has a protective function and prevents damage. This point is very important, because strong winds often bring to the roof of pebbles and twigs, which can cause scratches and dents.

Striking the surface of the roof, debris can damage the paint on the surface. In such areas when moisture is formed corrosion gradually damages the material and reducing the operation time of the roof. Due to the composition of the overpainted this possibility is excluded.

Under the varnish are dirt and aluminum layer. The finished product has light weight, which facilitates transport and subsequent installation procedure. Weight 1 m² of the material is from 3 to 5 kg, depending on the thickness.

Before packing any type of roof sheet installed vapor- layers, water and heat insulation

Metal roof: types of materials from different raw materials

Furthermore the steel sheet for the production of metal can be used and other raw materials, such as aluminum or copper. In each case, the product takes on special properties due to the material from which they are made.

The steel sheet coated with zinc is the most common raw material for the creation of metal. The final thickness of the product in this case may be 0.45-0.55 mm. In rare cases, the figure comes to 0.6 mm. Due to the zinc coating provides reliable protection from the corrosive effects of the metal. Above the deposited multiple layers to increase the strength, there are included a polymer. It may also be used with steel aluzinc or zinc.

Useful advice!If you want to achieve maximum durability, use for the organization of roofing material coated with a Aluzinc. Accordingly, the price of this kind of coating substantially higher.

The product of aluminum has another important advantage - the material did not corrode. Despite this, the product is applied to the additional coverage, but it is done with the aim to cement metal roofing and increase its service life. In the aluminum tile has another beneficial advantage - very light weight. The disadvantage is it that the limited color palette and high cost.

A roof covered with the sheet material of brass

Tile copper sheet has a refined and noble appearance. Over time the material formed on the surface characteristic of the coating materials in the form of greenish patina. But it does not reduce the decorative coating properties, but on the contrary, emphasizes them.

Like many monuments and historic buildings, metal with a green patina looks quite interesting and attractive. Patina serves to protect the role of the adverse impact of external factors, therefore, the need to apply additional polymeric spraying is eliminated. The cost of this coverage is quite high, so it is used very rarely.

Forms of metal roofing: photos and a range of materials

Classification is based on metal geometry that is inherent in the profiles, as well as on the depth of the insole products. In each case, the coating offers an interesting and unusual design. Roof with a profile of Monterrey has similarities with clay roof tiles. This type of coverage from Finland very quickly found fans, thanks to their advantages:

• ease;
• aesthetics;
• easy installation;
• high resistance to environmental factors.

Metal profiles with Monterrey brown

Note!The material has a distinctive appearance because different brands of metal produced similar products in Monterrey with smoothly rounded profile. Edge portion is in the form of steps, are arranged symmetrically or asymmetrically. It depends on the design and manufacturer specific.

Metal profile-based Cascade looks like a chocolate bar. It is economical and is suitable for the organization of the roof on the roof with a complex shape, thanks to its rectangular shape. Design turns a neat, proportionate and sufficiently strict. Therefore, the metal roofing on the basis of the profile cascade can be considered a classic. It is universal and will always remain relevant.

In today's present product range of round and sole ridge parts in the classic version. These features are inherent to the metal tile profile Joker, which resembles a ceramic coating due to its good waves. This type of roof is considered traditional.

Roof framed using a metal profile Banga

Modern roofing materials for roofs, new metal species

Metal profile-based Banga belongs to the category of new products, as has been invented recently. Are inherent unusual forms and original external performance. Wave has an increased height. In conjunction with the non-standard structure peculiar profile generated three-dimensional image. This type of metal is characterized by a small width, but this does not affect the merits of the coating. Most of the material used for the organization of the roof on tall buildings.

Among the new options of the roof also provides metal with the shape of the profile of Andalusia. She's still not popular among developers and owners of country cottages, nevertheless benefits from this material is sufficient. The most important and profitable of them is a hidden fastening system, which can not boast of even such high demand as a tile Monterrey. Screws on the outside does not look aesthetically pleasing and eye-catching. Metal Andalusia completely solves this problem decorative.

Note!Due to a lock tight adhesion coating is continuous, so the roof gets improved moisture resistance.

Profile type and sheet size Andalusia

The most recent and little-known metal tile roofing is the profile of Shanghai, came to our market from China. It has a complex symmetrical pattern. Profile has a height of 66 mm. Often, the same equipment used for the manufacture of profiled sheet.

Prices for different types of roof tiles

On this list of materials under the category of "metal" does not end there. Previously been listed only the main species in high demand. Actually covers much more.

Prices for metal roofing different brands:

Metal as a roofing material is sufficiently durable. The term of its operational life is 50 years. The average cost rate is within the range 500-1200 rub. / M².

General advantages:

• Easy and fast system mounting;
• sufficiently to set the presence of just one person;
• highest strength;
• Resistance to mechanical properties;
• light weight and simple transport system;
• affordable price.

Deficiencies in the material is not so much. In the process of mounting a large amount of construction waste, which affects the cost. In addition, the products have a high sound conduction.

Beautiful embossed metal Ruukki Finnera

Decking: types, photos of the roof of a private house roof

Profiled flooring or gofrolist made from the same material as the metal. In manufacture the cold rolled steel, which is covered with a layer of hot zinc. In some instances, the thicker sheets that have wavy or rectangular profile.

Note!Profiled sheet has a wide range of applications. special grade of material available for the organization of the roof: H60, C8, C44, C21, N57, NS35.

On each side of the steel preform is covered with a protective layer of zinc or aluzinc. As a further protection layer made of polymers is used. In the production of the following forms of corrugated board profiles are used:

• wave;
• trapeze;
• rectangle.

Decking - common material for decorating the roof

Work on the installation of the mounting metal sheets being carried out quite easily. But here it is not without certain requirements that must be met. Installation can be carried out only on the surface with a slope of not less than 10 °. The maximum allowable rate is unlimited slope.

The material is laid overlap approximately 20 cm. Subsequently, this gap will be filled by a sealant. Reliable fixation is carried out by self-tapping screws. Flow fasteners per 1 m is 6-8 pieces. In some cases, the installation of profiled sheet is carried out over the old roll roofing.

Scope of metal sheets for a roof and its advantages

Profiled sheet refers to the category of durable and reliable materials, and thanks to its affordable price it is quite popular. Scope metal profile extends as a roof structure for household purposes, for example, sheds, sheds, Garages etc. Often they are covered with shops, industrial sector companies, car washes. I profiled able to last almost 50 years.

For the organization of the roof sheets are used in a monochromatic color scheme, which can be very diverse.

The weight per square meter of the profiled sheet is 8-12 kg

Note! Production produced profiled with imitation stone or wood: the steel sheet is applied over the pattern, and then a protective layer made of polymers. However, this option is usually the material used for the construction of fences.

Such an extensive range of applications due to the large list of advantages and advantageous characteristics of the material:

• high resistance to corrosion;
• durability;
• simple mounting system installation;
• high strength;
• ability to maintain their appearance throughout the service life;
• resistance to weather changes;
• light weight roof, which is why there is no need to strengthen the support of the building;
• Resistance to physical properties (mechanical damage and deformation).

Due to the protective coating has a high moisture resistance decking

Metal profiles: prices for roofing material

As well as metal, corrugated sheet belongs to the category noisy roof. Therefore, you definitely need to perform high-quality sound insulation. The rest of the material does not have serious drawbacks.

Prices for the purchase of metal sheets:

Ondulin as a roof for the roof: types, material price

Onduline is one of the materials related to the type of roofing sheet. This coating is popular among consumers due to its naturalness and affordable cost. Material is created on the basis of thin cellulosic fibers which are impregnated with additions of polymers and bitumen.

Note!Onduline has other names that are used in the construction market: Aqualino or evroshifer.

The coating is colored polymeric paint exhibiting resistance to temperature. On sale occurs ondulin with single and double layer painting. Standard sheet weight of 6.5 kg. Billets made in the form of waves which reach heights of 36 mm. 2 m long sheets having a width of 0.96 m. These parameters are regarded as the standard, but there are other dimensions, e.g., 0,76h1,95 m.

Average prices for the purchase of Ondulina:

When buying Ondulina important color. From coloring sheets and other elements to the roof depends on the final cost of the material.

Related article:

Ondulin: price per sheet, the dimensions and properties of the soft roof.Properties evroshifer. Technical characteristics of the material. Price per sheet Ondulina SMART. How much is ondulin Shingles? editing features.

Features and Benefits Ondulina

Onduline is used for the organization of the roof on the garage, carport and bathhouses. Superior flexibility, this material is optimal for the formation of the roof of the complex type. Ondulina characteristics and useful in the repair of an old roof.

When working with ondulin very important to observe the installation requirements:

• minimum angle of inclination of the working surface is 6 °;
• inclination angle exceeds 10 ° - lathing performed continuous structure;
• angle 10-15 ° - lathing based timber, assembling elements with a pitch of 45 cm;
• inclination angle exceeds 15 ° - lathing increments of 60 cm.

Useful advice!When installing Ondulina sure to use special nails. They not only provide high-quality fit, but will be invisible against the background of the roof, if you pick the proper coloring sheets fasteners.

The minimum angle for the roof assembly is 6 degrees Ondulina

Advantages of a roofing material:

• highest water resistance;
• environmental friendliness, safety and hygiene;
• resistance to aggressive chemical substances;
• ability to withstand a high level of activity (about 960 kg / m under the condition that all installation rules are met);
• light weight;
• Easy mounting and conveying system;
• easily processed (cut out is easy even with a hacksaw intended for working with wood);
• complete quiet;
• affordable prices.

Weaknesses of Ondulina roof

As can effectively serve regard to water resistance ondulin for 40 years. During this period can deteriorate the appearance of the coating, as the paint fades before the material is fully comes into uselessness.

Ondulin recommended to lay on the roof of buildings, which are located on the sunny areas

cover Disadvantages:

• paint on the surface exposed to fading;
• Low flammability limit (of 110 ° C);
• if the coating is under low light, moss grows on top of it after 2-3 years;
• in hot weather it is impossible to carry out work on the roof, under the influence of temperature coating exudes a strong smell of bitumen and softens.

On the market there is another kind of material - onduvilla. It has similar features and characteristics ondulin, but it has a high decorativeness and an extended size range. onduvilly sheets have a smaller width.

Properties as a slate for roofing sheeting

Slate is one of the most accessible of coatings for the organization of the roof. Sheets of this material to consist of 85% Portland cement and 15% of asbestos.

Building roof covered with roofing slate sheets

Standard parameters of sheets:

• weight - 10-15 kg;
• length - 1.75 m;
• Width - 0,98-1,13 m;
• the number of waves - 6 pcs 7 pcs.. or 8 pieces.

Slate used as roof covering for street toilets, bathhouses, Outbuildings and sheds.

Note!This kind of material can be used in the construction of private homes. As a rule, it is applied, if the budget for the construction of the building is limited.

The average cost of Slate:

Colored slate types look more attractive and aesthetically pleasing, but their cost is much higher than that of conventional sheet material.

The specifics of the installation and the properties of slate: the advantages and disadvantages

Installation work of laying slate performed strictly on the inclined surface. The allowable tilt angle is in the range 12-60 °. Sheets are stacked overlapped approximately 1-2 wave.

For conventional slate suitable crate made of square cross section timber with a size of 50 mm. design elements stacked in increments of 0.5-0.55 m. If material has been purchased with reinforced profile, should be made more reliable crate. To do this, take the bars with a 75 mm cross-section size and increase the pace of their installation to 0.75-0.8 m.

For the installation of slate constructed crate with 50-60 cm increments

To install the roof slate special pre-fit lining of glassine paper or roofing material. Soft substrate must be applied and for each fastener (tack).

cover Advantages:

• low cost;
• ease of processing (cutting the material can be performed using grinders);
• Absolute non-flammability.

Terms effective service slate apply for a period of 30-40 years.

Negative aspects of the use of slate:

• fragile structure;
• one of the components of the material - asbestos, which is a source of danger to human health;
• highest hygroscopicity provokes accumulation of moisture in the sheet, because of which on the surface thereof starts to grow moss.

Asbestos roof is not recommended for residential buildings

Seam roof: roof types, roofing materials and pricing

With the popularity of standing seam roofing is increasing every year. This is due to cover the reliability and high level of protection against the negative impact of weather conditions, as well as excellent quality.

Note!Standing seam roof is often used for the organization of the roof on the buildings, the architecture of which is made in the style of Russian classicism. To date, this type of coating is actively involved in the restoration of historic buildings reconstruction.

for seam coating on the workpiece are roof with special techniques. Special joints are used which are formed by the connection of the roof parts. Varieties standing seam welds:

• single;
• standing;
• double;
• recumbent.

Types of seams seam metal coating

During installation the coating is obtained on the basis of metal sheets bonded seaming. This roofing system among developers is considered the most reliable and durable.

Seam roof based steel elements

Steel roof formed of sheets coated with zinc. Often elements are additionally protected by the polymer layer. Depending on the species of the rebate, which is on the sheets, it made a certain type of attachment. Stacking material necessarily performed on the inclined surface. The minimum allowable angle of inclination is 14 °. In addition to the crate, which is used as a base for mounting a coating is laid onto the surface of special film. It eliminates the formation of condensation under the standing seam roof.

For the manufacture of crates required square bars with a size of 200-400 mm in cross-section. If the roof has a slope surface within 7-14 °, the base is performed in a continuous structure.

The roof of the two-story home nestled standing seam roof

Advantages of steel standing seam roof:

• Absolute non-flammability;
• highest flexibility, so it is possible to perform the finishing of roofs with a complex structure;
• aesthetic appearance;
• light weight (weight range 4-5 kg ​​did not require reinforcement truss system);
• resistance to low temperatures.

Useful advice!Despite the fact that the main application area of ​​the roof extend to manors and churches, rebated coating can also be used in modern construction. Use it to organize roofs on industrial buildings.

cover Disadvantages:

• vulnerability to attacks;
• It requires mandatory thermal insulation (seam roofing is very cold);
• DIY installation is possible;
• limited market for installation services;
• material accumulates static electricity;
• high noise levels.

Profile types and sizes cover the seam (sheet length 8-12,5 m)

Operational cover a period of about 25-30 years.

Other types of roofing roof of the rebate

Blank for forming the standing seam of the roof can be made not only in steel. For these purposes the copper and aluminum. Such nestrashnye corrosion coating, which already suffer from other types of metal roof.

Standard parameters of copper blanks:

• thickness - 0.3 mm and more;
• length - 110 cm;
• Width - 70 cm;
• Weight - 5.10 kg (aluminum roofing is light weight 2-5 kg).

During operation, the surface of the copper and aluminum roofing is formed by a film coating. It prevents the destruction of the material due to corrosion. This ensures increased operational terms of service. Copper is able to last for about 100 years, aluminum is a little less - 80 years.

The service life of standing seam roof is at least 25 years

Advantages coating of aluminum and copper:

• no need special care (producing sufficient cleaning procedure 2 times per year);
• complete non-flammability;
• environmental friendliness;
• cleanliness and safety;
• invulnerability to corrosive and chemical action (acid rain).

Among the disadvantages of only the high cost can be identified, which is within 2000-2700 rubles. per m².

steel standing seam roofing cost roofs of private homes: types of protective coatings

Steel billets for standing seam roofs may have a different type of protective coating. Each of them has its own advantages, features and decorative characteristics.

Process mounting seam roof

Note!Type of protective coating directly influences the cost of the rebate.

The table shows the average rates for the purchase of rebate blanks 0.45 mm thick for a roof for the difference in the protective coating.

Rates on the steel standing seam roofing:

Roof Roof: types of coatings and their characteristics

The first weight is given greater importance when installing roof. Even if at first glance it seems that the sheeting weighing 3-4 kg are not able to reload truss system should take into account the total weight of the coating, which in fact would not be so small. On the other hand, if you want to take self-installation of the roof, the purchased material should have a simple mounting system, easy to handle, open and repair.

All these requirements are met by different types of soft roof, which photo you just might meet online or even see these materials on the street.

Sloping ceilings covered with soft tile design

Roof has the following advantages:

• resistance to adverse environmental effects (the material retains its properties even under the influence of high and low temperatures);
• excellent strength properties, particularly tear;
• Easy installation system;
• the minimum number of tools needed for the organization of the roof;
• coating installation in roofs having a complicated construction, without complicated preparations;
• no noise during further operation;
• fire safety;
• long service life - up to 15 years.

Note!Roofing felt, which relates to a roll type roof is not fire-resistant coating. This version of the material removal from the list soon.

Other buildings on the site are decorated in the same style with the use of a soft roof

Roll and membrane materials, soft tile: photo roofs

The soft coatings category contains other items in addition to the soft tiles. Types roof allocated based on the raw material used for their manufacture:

• mastic different types;
• the membrane of polymer materials of origin;
• soft or shingles;
• coating roll type.

Most of these materials are able to offer very favorable characteristics, not only technical but also operational:

• high strength;
• flexibility;
• corrosion resistance;
• water resistance;
• quality sound insulation;
• anti-fungal properties;
• good thermal insulation.

Mounting soft shingles

Thanks to all these advantages, the soft cover for the roof were so widespread. Field of application:

• private houses;
• cottages;
• warehouses;
• objects of industrial area;
• large commercial buildings.

If you are looking soft roofing material in the first place should pay attention to the level of heat resistance, and has then consider other characteristics: the level of elasticity, flexibility and strength in relation to mechanical exposure.

With regard to the mastic, there is a priority indicator is the percentage of solids content, the level of adhesion as well as the time required for full cure. Durability plays the role of an important role in the choice of any variant cover.

Flexible roof is perfect for mounting on roofs of complex constructions

Features soft tile: photos, specifications and pricing

Soft tile called bitumen, obtained by cutting the web material. Each leaf holds four rectangular, rhomboidal or hexagonal element. Through the use of various dyes on the market there are several material options:

• natural covering of tiles;
• antique surface overgrown moss;
• antique surface overgrown with lichen.

Note!Despite the fact that the shingles with characteristics similar to piece goods, it still belongs to the coil coating type, because of the structure and scope.

Prices for the purchase of shingles:

The service life of asphalt shingles are about 15-20 years old. Installation is performed on the inclined surface. The minimum inclination angle is 10 °. Soft tile can be used not only for the organization of the roof, but also as a coating on the walls of adjacent vertical zones.

Membrane coating: characteristics and price soft roof for 1 square. meter

The membrane coating on a roof has a thickness in the range 0.8-2 mm. This type of material has several varieties, depending on the raw materials used in production. Types membrane coating:

• PVC - made from polymeric materials (which provides protection against heat and UV radiation);

Membrane roofing, roll, made of PVC

• EPDM - served as the material for the rubber coating is reinforced with a mesh made of polyester (strength, environmental safety);
• TPO - thermoplastic feedstock olefins reinforced mesh (ecology) are used for the production of coatings.

Note!Since PVC membrane coating is made from a polymeric material origin, the variant of the roof can not be called environmentally friendly.

Rates on PVC membrane coating:

The service life of a membrane coating to the roof is about 50 years. Due to the large width of the material it is convenient to cover the roof, where it can be done at any time of the year. No need for installation of additional hydro-protection.

Among the drawbacks may be mentioned only the complicated preparatory stage as roofing membrane does not suffer pebbles and debris on the surface. Solvents and organic oils can damage the material.

The specificity of the soft roll of roofing: types and prices

Soft roll roofing offers several different materials for the roof. The most popular and affordable price is the roofing material. Production following scheme is used for manufacturing:

• forming the preform of roofing felt;
• impregnation of bitumen;
• mixture sided machining on the basis of bitumen with a high hardness and a mineral filler;
• applying an outer coating in the form of a special granular material.

Roofing material is often used as a coating for flat roofs

The lifetime of the material is 5 years. In addition to the roll, there is also a tiled roofing material, but it has a completely different circuit fabrication and properties.

Useful advice!If you want to get a longer life, it is necessary to purchase roofing material made of modern technology. Through the use of polyester fabric or fiber glass sheet operating periods are doubled.

For roll coating category refers rubemast. This type of roof is a bituminous surfaced material with a higher percentage of binder than roofing.

There are a number of similar coatings based on glass:

• Steklomast;
• Fiber-glass;
• Stekloizol;
• evroruberoid.

The cost of roofing materials for the roof:

Materials based on glass fibers are characterized by a long service life. The minimum period of operation is 20 years. This category of roofing has only one drawback - vulnerability to the impact of low temperatures. But the problem is easily solved by a multi-layer assembly (3-4 layer material).

Modern roofing materials: Rizolin

Rizolin refers to content of the current generation with a flexible and soft texture. And a self-adhesive coating is performed on the basis of the reinforcing fabric, which is filled with a mixture of bitumen and the polymeric materials and special additives.

Note!Thanks to the foil surface material can be colored using any synthetic dyes in order to improve appearance.

Rizolin - contemporary bitumen-polymer coating with the foil surface

Rizolin varieties:

• A - two-sided self-adhesive surface;
• P - self-adhesive surface on one side and the other resin base;
• F - aluminum foil base and a standard adhesive surface.

Material with Rizolin foil surface provides reliable protection from premature degradation, and also slows down the process. In the present embodiments range of products with a copper base which are coated with a very thin layer of foil.

Prices for the purchase of Rizolin:

Each of the examined coatings bears certain advantages and disadvantages. When choosing a roofing material should take into account the characteristics, scope, and rely on their own taste preferences and financial capabilities.