3D self-leveling floors, how to make their own hands - a simple step by step guide

Bright and voluminous 3D-drawings - a beautiful design element, which is now used as decoration for the walls and for the installation of self-leveling floors. Such coatings compare favorably to other, not only in the decorative aspect, but also in terms of strength and reliability. Of course, there is such expensive than many other finishing options, and installation technology is a complicated process. But pour yourself such coverage is still possible.

What is needed for 3D-Paul

The composition of the coating consists of three layers: the base, the one that is applied to the image and the finish trim. The last layer is often treated with special lacquer coating which protects against mechanical influences. The first and last layers are made of bicomponent polymeric composition which includes a curing agent and a transparent material.

Attention! In preparing the polymer mixture should be kept the right proportions, the composition has not turned too thick or liquid. In both cases, the quality will suffer coatings that affect the durability and sex life.

For decorative layer can be used banner fabric, acrylic, vinyl and various small details, whether it be pebbles, pieces of wood, shells and other items. Also for grouting applied polymer clay or gypsum, by which fill voids formed between the decorative fragments. You can, of course, order a ready material for the decorative layer, but the cost is such a pleasure to be expensive.

Making pictures

For decorating with photo printing 3D-floor can make the image yourself. First you need to pick up the picture. There are suitable, for example, the image flower fields, beach sand, stones, leaves, and other natural ingredients. You can also use any patterns, or abstraction. The main thing is to fit the image to the interior and had a good coloring.

After selecting the image should take a picture of the floor of the room in which the work will be carried out. It is advisable to take a snapshot of the entire area. You will need a good camera, as the image needs to get high quality. Further processing is performed on images in Photoshop. The picture of the room is loaded into the program, and it is applied the selected image.

To transfer the image onto the fabric, it is necessary to use the services of the company, which is engaged in the outer seal. For the experiment, the best first book of black-and-white image on the paper. It must be placed on the floor to figure out whether a sufficiently realistic picture turned out. If everything is in order, you can print it on a banner fabric.

Mounting3D-Paul - step by step guide

Step 1. At first dismantled old coating. If the screed below it smooth, you will simply seal the existing defects with cement mortar. If the base in a bad condition, you will have to fill in a new tie. After the solution has dried, it is desirable to perform the grinding surface.

Important! Also check the evenness of the base using a spirit level. After all, even in the presence of a small slope complicated casting process, plus the increase of the polymer flow.

Step 2. Upon completion of surface preparation procedures needed vacuum. Then, the base treated two layers grutnovki. After drying of the primer coating composition is kneaded for a base layer. Components poured into the prepared container and mix with a mixer construction. The finished material is supposed to be uniform.

Step 3. Further the solution was poured on the basein the opposite corner from the door and rolled with a needle roller. When you work in a large room fills performed stripes, borders are smoothed wide spatula. Polymer mixture hardens quickly, so the adjacent portions of the need to have time to fill in for 10 minutes. When this layer has to be uniform with no air bubbles inside.

Step 4. After drying the basecoat, glued decorative painting using the same polymeric material. Only for this purpose it twice diluted with an organic solvent. Glue is applied to the floor, the fabric is rolled and pressed with its dry roller, squeezing out any air convexity. It is necessary that the material edge protrudes slightly beyond sex. After fixing the covering them pruned.

When using in place of the printed image small decorative elements placed on their surface. Prior to this, the foundation is primed polymeric composition. After filling in the entire area of ​​the gaps between decorative elements overwritten polymeric clay.

Step 5. When the decorative layer is prepared, pour topcoatFor which use the same composition as that for the base layer. The material is also unrolled roll. The layer thickness should be 3-4 mm. Upon completion of all work surfaces can be coated with a protective varnish.