Outside shower Shower in the country with their own hands: how to connect the system

Water Outdoors procedures are very useful, so many supporters of relaxation and hardening take the decision to make an outside shower to shower the country with their own hands, or at least at the site ready to install booth. This article will help you understand the design features, to choose the right size and place of installation, make a preliminary scheme and without errors fulfill all stages of construction.

Outside shower Shower in the country with their own hands: the choice of designs and design

Construction of street soul - sometimes the only way to fully wash after a busy day spent in the garden, or cool off in the summer heat. This small building has a lot of variants, both technically, and in terms of aesthetics. However, all designs have a similar device.

Standard cottage shower consists of the following elements:

• the carcass part;
• a water tank;
• enclosure (wall);
• pallet (floor).

On the Internet you can find a lot of interesting photos, soul depicted on them, have diverse architecture. And there are not only traditional, but also quite unusual and original design version.

There are several options for the design of assembly:

• simple construction having no strong side walls;
• light type structure with improvised guardrail;
• shower cabins capital type, in which the walls are made of polycarbonate and other materials.

In addition, distinguished booths closed and open and half-closed structure. There are versions with two partitions: one zone is plumbing, and the other is for storing bath accessories, towels and clothing.

According to the Method of water supply cottages souls are of two types:

1. Water - is fed to the booth water supply system is centralized.
2. Capacitive - at the top you are installing tanks for summer shower water, which is heated under the influence of sunlight. For these purposes may be used cans or drums.

Note! Fitting shower depends on how the water supply. If the construction of the proposed location is in close proximity to the house, it is advisable bring not only a centralized water supply system, but also to organize the sewers to divert waste water.

How to make a drawing for the construction of the shower at the cottage

The design is simple garden shower includes only one stall for bathing, so do not need to develop complex drawings for construction. Most often depicted the souls of the photo in the country with their own hands have standard dimensions -. 1h1h2,2 m These figures correspond to the lower boundary of the construction at the booth is not allowed. About 0.1 m height is given under the arrangement of the pallet of about 0.15 m is required for hanging from the ceiling watering.

Significantly exceed the permissible height of the parameters is also not recommended. Otherwise, the complicated process of filling the tank with water, and a man with a slight increase will be difficult to reach the crane, which is set in front of a watering can.

The depth and width shower to give selected individually. But still it is not necessary to cut the design size less than the established standard sizes, or inside will be very closely. If you figure masters soul sufficiently large, the width and depth of the booth is chosen so that people can comfortably bathe.

Construction of the soul in the country with their own hands: photos and tips to enhance design

If the budgetary possibilities permit, and there is a desire to develop further the construction of the scheme, it is possible to add extra convenience. In the presence of light use the shower will be much more comfortable at night. For these purposes, you can use any type of lamp with a low power level. The main thing that it was attended by the required level of moisture protection. During the day will be enough natural light. For this purpose, a small window can be cut in the upper part of a door or on any of the sidewalls.

Useful advice!To eliminate the possibility of occurrence of drafts, a window in the shower, it is desirable to glaze.

It recommended as a container for the soul of summer buy tank square shape. Setting it at the top of the booth, you can save on the purchase of roofing material, which in this case is not required.

Do not create a fully sealed structure. In such conditions inside the booth will gather steam, because of which is difficult to breathe. To avoid such consequences, it is possible on the back or side wall to install a small ventilation hatch. Since hot air is much easier to cool, the hatch mounting is performed in the upper zone of the booth.

If the design will be used in the cooler times of the day, experts advise to buy for the garden outside shower heated. To build such a structure alone, is sufficient to establish a tank equipped with a built-in TAN. The heating element operable at the expense of electricity, will ensure that the hot water at any time.

A useful addition to the walk-in dressing room will be. It can be located inside or outside the cabin. In the first case it is necessary to increase the size of the house. Storage space for clothes quite separate from the membrane screens.

In order to organize a comfortable locker rooms, you can use the dressing room. Its design is constructed and installed so that one of the walls adjoining the shower. For this insert additional racks, after which skeleton is sheathed by any type of sheet material. For more comfort you can put in benches and compact table.

Before you make the shower at the cottage personally, you need to make sure that in the diagram, even the smallest elements were recorded, down to shelves, coat hooks and mirrors. If the booth construction is designed for several people, the drawings must include a drainage system, as well as the placement point of the drain hole.

Construction technology of summer soul with his own hands: photos and step by step instructions

Once all designs conceived nuances and composed drawing, it is necessary to choose the optimum location for the installation of a shower. It is desirable that the construction area is located at a distance from buildings and tall trees. Shower heated at giving the nuance is not particularly important, but if the water in the tank will be heated in a natural way, the place where the cabinet is located, must necessarily be solar.

Important! You can not put the shower on a site located in a low place. This placement of the negative impact on the further operation of the stall as the water flow will be impeded.

There are several options for wastewater system arrangement. If you plan to walk or infrequent use volumes of water consumed will be small, it is possible to limit the formation of a drainage layer, which is located at the bottom of the pan. If the booth is designed to service a large number of people who will require the construction of a septic tank. In this case, the waste pit is not recommended to equip the right under the shower, otherwise not be able to avoid unpleasant odors. It is enough to install a septic tank at a distance of 2-3 meters from the building.

Creating slab and pile foundation for a summer shower to give their own hands

In most showers are lightweight, but heavier construction due to the presence of a tank filled with water, which is installed on the roof. To house remains stable, solid foundation formed under it. One of the most common variants of the foundation is a monolithic slab. the concrete used for its construction.

The procedure for the construction of the foundation slab for a garden shower with his own hands:

1. In accordance with the size of the shower stall at the site excavated pit depth of not more than 0.5 m.
2. Along the perimeter of recess mounted formwork construction.
3. At the bottom is formed of sand and crushed stone airbag thickness of 0.2 m.
4. Performed installation of the reinforcing mesh.
5. Formwork design is filled with cement mortar. This is done so that the base plate of the future rose above ground level by 0.1 m.

Red bricks can be used for the construction of the formwork construction. Before execute grouting, is required to lay a sewer pipe, drain providing wastewater. Make this procedure must be precisely at this stage, because later it will be impossible to implement.

During the construction of wooden soul to testify recommended to use foundation on stilts. To do this via the drill need to make holes on the perimeter of the structure, the depth of which is 1 m. They are placed inside the tube. These may be metal or asbestos products. They should be pre-cut so that after installation they rise above the ground level by about 0.2 m.

Important! Be sure to make sure that all pipes are installed strictly in a vertical position. Only after that can do grouting.

Filling is carried out both on the outside pipe, and inside them. Pre-need to do the installation of the anchor pin. After solidification of the concrete frame is formed lower binding to lockers. wooden beams can be used for these purposes. There are drilled holes for mounting studs. Then the frame with the nuts tightly joins the piles base.

Construction of columnar and strip foundation for the soul of summer in the country with their own hands

As a basis for the construction of the shower can be used columnar type of foundation. Its design is very similar to the pile plan. The only difference is in the technology supports. It is necessary to dig at the corners of the booth pit size 0,2h0,2h0,5 m. If desired to produce or buy summer Shower for dacha with dressing room and with the pallet will have to increase the number of wells to 6 pieces. Additional recesses are located in the central part of the long walls.

Wall formed recesses need to lay a roofing material. After that, the center mounted anchor studs. For grouting required to produce formwork construction. At the final stage of the frame remains attached to the sill lockers studs.

The article on the subject:

Construction of toilets in the country with their own hands, drawings, dimensions

Types of autonomous toilets. The choice of location for the construction of a toilet at their summer cottage

If you plan to build major soul to give his own hands made of brick, it is desirable to use a belt type foundation. Along the perimeter of the future construction of the trench is formed. The optimum depth is 0.5 m. Further, the formwork assembly is performed. At the bottom of the trench is necessary to form a cushion sand and crushed stone of 0.1 m thick. Thereafter stacked valves and filling is carried out with concrete. It must be done so that the ready-made foundation towered above the ground approximately 0.1 m.

When the base is completely hardens and dries, it will be possible to start the construction of the sewerage system.

How to organize the drainage system in the soul of the country with their own hands

There are several ways to organize the sewage system in the bathroom stall. The choice of construction technology depends on several factors:

• the type of soil on the site;
• the form of a foundation base;
• the number of people living in the house.

If as a foundation for a summer shower in the country used a monolithic slab, before performing the fill system is necessary to lay plastic pipes with a knee. Plate formed in such a way that on all sides has been a bias towards the drain hole. Sewer pipe is displayed outside shower and is connected to the general system of drains. Can be brought to the drainage gulleys.

Useful advice! For a similar construction for sanitation lockers installed on the foundation of another type, not necessary to perform the fill concrete floors. Enough to buy a summer shower to give a pallet made of acrylic. This element will perform the floor function.

shower with a connection to the sewerage system - the best option for large families, since the pit will not be able to accommodate the volume of waste that will be formed during the operation. If the structure is designed for 1-2 people, it is enough to drain directly under the cabin. But this kind of system is suitable for areas with a loose type of soil, when the shower is installed on the columnar or pile foundation. This embodiment can be used on the tape base.

To start to remove the layer of soil depth of 0.5 m. Recess formed on half of its height filled with gravel or stone. The remaining part is filled with a fine gravel fraction. Once assembled booth design, on a layer of gravel set pallet made of a wooden lattice. The system is arranged so that the waste water passed through the drainage layers and is gradually soaked into the soil.

Sometimes the owners of summer cottages output sewer in the garden that can not be called a good solution. If still resort to such a method, it is desirable that the place where the water is drained, well-heated by the sun. Otherwise, liquid will accumulate, and is formed around the shower Marsh mosquito infested.

Production of cabins for summer shower Photo and technology of building constructions

For the construction of the stall any available materials can be used for an improvised shower.

For these purposes fit:

• wood;
• polycarbonate;
• corrugated board;
• brick.

Each type of material has its own advantages, features and characteristics.

How to build a shower in the country with their own hands: Economy version of the booth

There is a little trick that will help achieve savings in the construction of the shower house. To reduce costs, it is sufficient to use one of the blank walls of the building as a side to the booth.

Before you build a summer shower budget type must be secured to the wall of container for small-scale water, equipped with a watering can. Here it is possible to establish comfort related elements, for example, clothes hooks, shelves etc. a partition located in the upper part of the future structure. It is fixed to the wall of the building. As the door tarpaulin or film (necessarily opaque) can be used. The shutter is suspended by means of rings.

Gender settling so that the waste water is discharged as far as possible from the foundation of the house. For this concreted site or you can do the installation of the pallet, made of acrylic.

Useful advice! If you use the inner corner of the structure, which has L-shaped, you can generally avoid the construction bokovushek booth. Their function will be to carry out the walls of the building.

Building wooden cabins suburban soul with his own hands

The most common variant of country soul - cabinet, made in the form of a wooden house. This type of structure is considered one of the most affordable in price. Wood is easy to process. However, it retains heat very well, which is an advantage if the shower will be used in cold weather.

For the construction of a summer shower in a private house with his own hands, it is desirable to use a wooden beam. For the manufacture of corner posts booths require a material having a sectional size of 10x10 cm. At the top of the shower tub installed, up to 200 l of water, so the timber should be sufficiently thick to withstand such a weight load.

For hanging doors need to install two additional stand still in front of the booth. These elements are placed between the corner posts. you can take a timber with a size of 5x5 cm cross section for their production.

To form a small deviation angle lockers pent roof, it is recommended to set the front corner posts 0.2 m higher than the rear. This is not required, if the container is used square-shaped tank. In this case, the racks are mounted on the same level.

All supports are fixed to the wooden frame sill. To fix is ​​necessary to use hardware and metal corners. The superstructure is tying in a similar manner. To secure more racks, you can use a spacer. On the upper piping core portion lockers formed the basis for the container mounting. It should be used to read not only the size but also the shape of the tank.

For plating the core portion can be structure to use a board thickness of 2 cm. Such a material is suitable for the manufacture of doors. It should be put in one row board and knock them together by two crosspieces. To prevent warping the door structure can be strengthened obliquely, using a long rail. Door frame made of boards, whose thickness for summer cottage shower is 4 cm. As recommended fastener screws.

When the cabin is fully ready, it can reveal the color lacquered composition. From inside the entrance curtain film, otherwise the door will swell from moisture.

Useful advice! Often used for the construction of a large barrel for the cottage soul. Setting on the design of a watering can, you can get a budget version of the wooden booths.

Manufacturing technology garden shower made of polycarbonate

Because wood is susceptible to deformation changes under the influence of moisture, many site owners think about how to make the shower the country with their own hands in a practical and resistant materials, for example, polycarbonate. The carcass part lockers made in the same way as in the case with wooden shower, but as the material is necessary to use a metal profile. Optimal cross-section size - 4x6 cm.

The carcass part lockers formed by struts and bridges between them. In this case metallic elements are used, therefore, the welding machine is required for their fastening. Moreover, the order of assembly may be configured in several ways. In the first case welded part carcass separately, after which it is established on the base and fastened by means of anchor bolts. The second method involves the concreting of the pillars during the pouring of the foundation. Then, a harness, attach the spacer.

As plating shower polycarbonate desirable to use a sheet material having a thickness of 1 cm. On a metal frame it is fixed by means of hardware that must have gaskets.

Installation of the tank and the construction features of the soul of the country with their own hands heated

At the last stage of the construction of the shower is installed tank. Capacity can be made independently using any container made of stainless steel or plastic. For this purpose, the bottom is necessary to form a hole with a diameter of 1.5 cm. To it is fixed by means of nuts tube section having a thread on two sides. The length of this element should be 30 cm.

The roof of the cabin in the middle need to make a hole where the pipe is inserted. After installation of the tank on the free end of the tap and are screwed head, made of plastic. Then the container is firmly fixed on the frame of the frame portion lockers, filled with water and covered with a lid.

To create a summer shower heated to testify is sufficient to establish the tank heating element. Of course, for heating the water can be used natural energy of the sun. In this case, electricity costs will be absent. However, the sun's rays are not able to heat a large amount of liquid. In addition, not every region has the right climatic conditions.

The network can find a lot of circuits needed to connect a summer shower for garden heated to electricity. The advantage of these devices is that the water in the tank warms up quickly, regardless of the time of day and the weather outside. In this case, the person himself can adjust the temperature. If a fix to the hose piece of foam, in a watering can will do the warmest water. For the same reason, fluid intake is carried out from the upper tank zones.

Useful advice! To speed up the process of heating a liquid, it is possible to make the coil circuit.

Can I buy a summer shower to give cheap: the price of ready-made designs

To simplify the construction of the technology, you can buy a summer shower the shelf and set it on the prepared base. The cost of the booths varied and it depends on various factors.

The price of the products affected by the following points:

• manufacturing material;
• modification (presence cloakrooms);
• form of the water tank (in the form of a drum, square tank);
• Components (presence of the heating element, the tank, the temperature sensor and the like);
• tank capacity;

• material of construction of the water container.

Average prices for ready designs

Name	price, rub.
Metal frame and PVC fabric
garden shower	7700
Garden shower with water heater	8900
Garden shower with a water heater and a cloakroom	12900
The design of polycarbonate
stall	11600
Cabinet to the tub 130 l	14800
Cabinet to the tub 200 l	15300
Cabinet with 130 l tank heated	16800

A wide variety of materials suitable for construction as well as manufacturing technology allows any cottagers to get comfortable and convenient shower in the country. And you can make your own booth improvised, or buy it ready-made in a specialty store.