Is it possible to put the tiles on the tile: expert advice

SHARE
in social networks

FacebookTwitterOkGoogle+PinterestVk

In the process of repair work with your hands have to deal with many complex issues, the correct answers to which will determine the quality and durability of the new finish. One such issue - whether it is possible to put the tiles on the tile? Consider whether you can use the old tile as the basis for a new coating or yet to dismantle its best to avoid possible problems.

Is it possible to put the tiles on the tiles: tips and expert advice

Laying new tiling on the tile can be provided high-quality testing and training base

Content

  • 1 Which may require saving the old tile,
  • 2 Is it possible to put the tiles on the tile: assessing the old coating
  • 3 Is it possible to put the tiles on the tiles on the wall features the works
  • 4 How to put the tiles on the tiles: characteristics of surface preparation
  • 5 How to stick the tiles on the tile: step by step instructions for operation
  • 6 How to understand that it is not necessary to glue the tiles on the tile: expert advice
  • 7 How to remove old grout from the tile joints
    • 7.1 How to remove old grout from the tile joints, if it is silicone
  • 8 Is it possible to put the tiles on the tiles on the floor: features of the work
  • 9 Can I make a self-leveling floor in the old tiles
  • 10 Is it possible to put the tiles on the tile in the street

Which may require saving the old tile,

There are several good reasons to create an occasion to reflect on how to give up the dismantling of the old coating before installing the new one. Mainly it is economic factors, among which:

  • significant savings of time and effort spent on repair works;
It's worth noting that a new layer of tiles must not be too heavy, if there is no confidence in the reliability of attaching the base

It's worth noting that a new layer of tiles must not be too heavy, if there is no confidence in the reliability of attaching the base

  • most likely in the process of dismantling will be faced with chipping separate pieces of cement-sand screed. This will entail additional work on its replacement or partial recovery. Also, in case the team has used the system alignment of drywall and plywood, it must be replaced;
  • in the process of dusting is minimized, which can not be said about when the old tiles have to shoot. In this case, you need to completely release not only the room itself, but also related to him, as part of the covering of the furniture and equipment polyethylene is not enough;
  • retaining the old coating can avoid having to deal with debris removal;
  • It is that the wait time required for complete solidification of the new ties is impossible. In this case also make better use of old tile as a base.

Thus, the reasons to retain the old coating can find many. The main thing - correctly assess whether you can put the tiles on the tiles in this case, so that as a result of the resulting coating was sufficiently robust and reliable.

The use of high-quality adhesive determines the duration of the service life of the new tile layer

The use of high-quality adhesive determines the duration of the service life of the new tile layer

Is it possible to put the tiles on the tile: assessing the old coating

In order to determine whether it is possible to produce a new tile laying on the same coating layer, it is necessary to make a preliminary inspection having a base. The first thing to ensure the strength of fixing all elements. It is necessary to note the presence of any, even the smallest chips, cracks and loosely fixed elements. To do this, you need to tap each tile with a rubber mallet. Loose items will rattle.

All the elements that are not well fastened or are cracked, be sure to cleave. Make a decision about laying new tiles over old need based on how large a percentage of the old tile is in good condition and securely held.

Useful advice! Pay attention to the existing floor level. As a result, installation of an additional layer of its height should not exceed a threshold height. If the thickness of the floor covering is too high, before the installation will be better dismantle the old coating and put new flooring directly on the substrate.

Before laying the foundation of a new layer of tiles must be cleaned of dirt and make a layout

Before laying the foundation of a new layer of tiles must be cleaned of dirt and make a layout

Is it possible to put the tiles on the tiles on the wall features the works

The main problem, which has to face in the process of installation of a new coating over the old - the impact force of attraction, because the tiles eventually will shrink and the old base should it survive. Therefore it is necessary to ensure maximum quality adhesion between the layers. Pre-need to take care of the clean-up joints, at least partial removal of the glazed tile layer and buy betonkontakt.

Useful advice!Betonkontakt usually applied with a spatula or trowel, carefully leveling it to the applied layer was maximally uniform. Flow rate should be approximately 300 grams per 1 m².

If laying new flooring is not planned in the process of laying tile on the wall, floor necessarily require protection. Baseboards and flooring need to lay a polyethylene film to avoid specific, and almost no stains.

To improve the attachment of a new layer of tiles on the old foundation is applied betonkontakt

To improve the attachment of a new layer of tiles on the old foundation is applied betonkontakt

In the case of a wall surface, betonkontakta drying period should be at least 5-7 hours. In this case, better to give preference to the more dense synthetic modifications as possible.

The rest of the tiling is done in a standard way gradually in small areas of the wall. This is due to the high drying rate of the adhesive composition. The elements are laid out on the area of ​​1-1.5 m² and are pressed with some force. Until such time as the adhesive hardens completely, some irregularities and imperfections can be corrected by using a rubber mallet.

Thus, answering the question or you can put the tiles on the tiles on the wall, focus on technology, and the finer points of the process. If you follow the recommendations of experts, the result of this work will be more than satisfactory.

Tile elements are attached to the wall using a special glue

Tile elements are attached to the wall using a special glue

How to put the tiles on the tiles: characteristics of surface preparation

After confirming that the old coating will withstand the expected load and is in good condition, you can go directly to the surface of the preparation for laying new tiles. The first is to make sure that the surface is able to provide the required level of adhesion, roughness giving the old tiles. To achieve the desired effect in several ways:

  • removing a tile from the upper gloss layer;
  • using the primer specific for surface treatment;
  • making an incision on the tile.

Each of these methods has its advantages and disadvantages. So, the easiest - the use of a primer, but it requires financial investments. The other two do not require the cost, but are associated with significant physical effort and plenty of dusty work.

Spoiled cover of the old items you want to remove or make incisions to improve adhesion

Spoiled cover of the old items you want to remove or make incisions to improve adhesion

Remove the top layer of tiles, as well as making the necessary incisions, can only use the grinder. These procedures allow to create the desired contact between the bottom layer of the new and old tiles coated. It is not necessary to remove completely the whole topsheet. It is enough will be 60% of the surface of the tiles. As for cuts, they are located at a distance of 1-2 cm from each other.

More simple and clean way - use a primer under the tile. The composition, which is also called concrete-contact, is able to give the necessary properties of any smooth and waterproof surface. With the glazed surface of the tile composition it adheres well, creating a rough top layer, which serves as a basis for the tile adhesive.

Before laying a new layer of tiles must be replaced grout joints of the old base

Before laying a new layer of tiles must be replaced grout joints of the old base

How to stick the tiles on the tile: step by step instructions for operation

tiling technology to old tiles involves the following steps:

  1. Using cement-sand mortar, obscure all places chipping, cracks and roughness so as to smooth the surface as possible. After this it is necessary to wait for the complete drying of the solution and hold the old coating purification, giving him of all contamination, moisture and lime deposits.
  2. Using one of the possible ways to ensure adhesion treated with the old coating. As already mentioned, it is easiest to use for this purpose a special primer.
  3. Smooth with a spatula, tile adhesive is applied to the reverse side of the tile, after which the composition is spread over the entire surface and create thereon special grooves using a toothed spatula. Simply put, at this stage of laying tile is made according to standard techniques.

Useful advice! When it comes to the partial withdrawal of the glaze or scored, then in the process must be used means of individual protection against breaking away of small particles and dust.

The process of laying a new layer of tiles on the old coating

The process of laying a new layer of tiles on the old coating

It is important to know that the complete drying of the adhesive in this case will require more time. This is due to low capacity to absorb the basics. That is why, all work related to the grouting, is best done not earlier than 3-4 days after laying. While fully preserving the standard technology, which utilizes a special composition and a rubber spatula.

How to understand that it is not necessary to glue the tiles on the tile: expert advice

Before you glue the tiles, every owner wants to be sure that his work will not be in vain, and the new coating will properly serve for many years. It is therefore worth pre-acquainted with the recommendations given by experts. They point to those aspects that may prevent secure fixation elements and serves as a warning signal, which is worth paying attention to:

  • in the process of tapping tiles preserves the integrity, but the sound that is heard, heterogeneous. This may indicate the presence of air voids under the tile, which can then lead to its destruction. The thing is that the old solution can not withstand the pressure and eventually disappear, both the coating layer;
Before laying the new tile layer should check the attachment of all the individual elements of the base, tapping them with a rubber mallet

Before laying the new tile layer should check the attachment of all the individual elements of the base, tapping them with a rubber mallet

  • often the question arises whether it is possible to put the tiles on the tiles in the bathroom or toilet. In this case, you need to pay attention also to the dimensions of the room, because the rooms are quite rare spacious, which means an extra layer of lining material solution and reduce the already small area premises. So if you see beforehand that this method will affect the size of the room, it is better to remove the old flooring and put the new one according to the rules;
  • poor base is old, cracked tiles, the upper layer of which has the natural prone to damage and chipping occurrence. If you put on such a basis is another layer of tiles, it is likely that it will last long, and all the work necessary to alter in the near future. This will entail not only a significant investment of time and effort, but also the financial costs;
  • before placing the tile on top of the old layer of cladding material, you need to make sure that it does not interfere with the free access to all communications and Audit hatches. Otherwise, the slightest damage will lead to the fact that for the repair work required to dismantle immediately the two tile layer. In this case it is reasonable to think everything in advance, so that in the future not faced with serious problems;
When laying the old tile, floor tile flooring are special operational requirements

When laying the old tile, floor tile flooring are special operational requirements

  • it is not necessary to put the tiles on the uneven floor. No matter how you tried, the situation only worse with a bias due to the additional layer, so it is better to dismantle not only the pre-tile, but also an old tie. After spending repair properly, you can remove as much as possible the existing imbalance. It is also worth paying attention to, before laying tiles on an uneven wall.

Having considered all of these recommendations, it can be concluded that before proceeding with the laying of the tiles over the old tile, you need to carefully weigh the arguments. The risk that the old coating will not sustain the load and simply fall off, destroying at the same time a new layer is always there is better to consider all possible options that, if necessary, to abandon the idea.

Related article:

How to lay tile to the floor laying techniques and technology features

Features of preparation of different types of surfaces. How to overwrite the seams. Criteria for selection of tile and laying patterns for the floor.

How to remove old grout from the tile joints

Quite often faced with a situation where the state of the old tile is quite satisfactory, but to use it as the basis for the new coating is required to hold a replacement for grouting seams. Carry out this procedure it is possible, but it requires time and attention. Consider how to remove grout from the tile joints correctly.

To remove the old grout used "rasshivatel seams"

To remove the old grout used "rasshivatel seams"

There is a special tool to remove the old grout, which is called "rasshivatel seams." With it can be removed by mechanical means grout. In itself it is a blade with a handle, but as an alternative, you can use an ordinary knife.

Knife blade or rasshivatelya need to walk on both sides at an angle and straight. Thus it is necessary to be careful not to chop off the edge of the tile. It is worth noting that to do it "by hand" is not quickly succeed, so you can use the drill with a thin drill or electric chisel.

Important!If in the process of removing old grout tile, too, began to crumble, it is better to abandon the idea to stack on top of another layer, even with the availability of the new grout.

How to remove old grout from the tile joints, if it is silicone

Silicone grout also requires removal and replacement, especially if the room is not high-quality ventilation has been provided. Very often faced with the fact that the joints are affected by mold, which is almost impossible to remove. Therefore, before placed on top of old tile new, you need to take care of the health of joints.

Remove old silicone grout by using a special tool or a conventional cutter

Remove old silicone grout by using a special tool or a conventional cutter

Removal of the silicone sealant is performed with a sharp knife or a special scraper. After that the additional cleaning with a vacuum cleaner.

Useful advice!There are special tools to remove the silicone faster and with less effort. Such compositions are applied using the cartridge gun, then wait at least 24 hours. Then the joints are wiped with a cloth or paper.

Is it possible to put the tiles on the tiles on the floor: features of the work

Floor covering, as opposed to the wall, is not affected by gravity. Therefore, in a sense, make styling easier. But in this case there is another difficulty - the new coating will be regularly subjected to heavy loads.

Before gluing the tiles to the floor, it is necessary to perform at least a thorough check of each element of the lower layer. You can use the same hammer for tapping, but you can try a different approach: the object with a flat base (good fit box), you need to gently pulled along the surface, carefully watching that no tiles do not fall even a few millimeters. Do it in a small bathroom or bathroom can be difficult, but for larger premises this is a very effective way.

When laying a new tile layer, you should pay particular attention to the level of the floor

When laying a new tile layer, you should pay particular attention to the level of the floor

In general, all of the recommendations that are provided in the previous section, relevant and in the case of the floor. It is advisable only to give preference to the mineral composition. Thus, the surface of a large flexibility will be provided that will enable it to withstand heavy loads and temperature changes.

Useful advice!Before you put the floor tiles on top of old ceramic coating may be omitted so intense preparatory work, as is the case with the wall. But moisten the base before proceeding with the application of the adhesive, still stands, as it has a positive effect on cohesion.

Can I make a self-leveling floor in the old tiles

As a basis for a new coating can be used and the inlet floor, which installation is carried out directly on the surface of the old tiles. As in all previous cases, the mandatory procedure - a thorough quality check of fastening of the bottom layer. All loose fitting elements compulsorily dismantled.

Filler floor can be used as a base for laying a new tile layer

Filler floor can be used as a base for laying a new tile layer

It is worth paying attention to the fact that in cases when it comes to working with a glossy surface, top coat layer is removed to provide the desired level of adhesion between the solution and tiles. Flooding, and further work is carried out according to the standard algorithm.

Useful advice!For laying a new layer of tiles does not require a thick layer of self-leveling floor. Its thickness should not exceed 5 mm. The main thing - to evenly distribute the composition over the entire surface.

Taking into account the opinion of experts, one can say that to do self-leveling floor on top of the tiles can be only in extreme cases. In this case, the floor area should be small, and the requirements for the performance characteristics of a surface minimum.

Is it possible to put the tiles on the tile in the street

Very interesting question that may arise - whether you can put a new layer on top of the old paving slabs. Of course, this procedure is often unjustified, but still in some cases resorted to this technology in the process of arrangement of garden paths, terraces and summer grounds.

When laying a new layer of paving slabs on the old, you must abide by laying all the layers of the substrate

When laying a new layer of paving slabs on the old, you must abide by laying all the layers of the substrate

As in the case of tiles laid on the old coating inside the house, the main criterion - the quality of the fastening of the bottom layer. Can be checked by using a tire iron or strong knife. With the help of these tools you need to try to remove one of the elements.

Important!If the tile was able to shift with a knife, but it was required to make significant physical effort, such a coating may be used as a basis. If the tile starred easily, hereinafter it may cause deformation of the upper layer.

Over the old tile layer is poured a new pillow, which should consist of three layers - loose soil, gravel, sand. At the same time carry out the seal of each layer is necessary separately. From above, according to the conventional technology, a new layer is laid paving tiles.

When laying a new layer of paving tiles on the tiles is worth considering that the floor level will rise due to the significant layer of the substrate

When laying a new layer of paving tiles on the tiles is worth considering that the floor level will rise due to the significant layer of the substrate

Thus, the answer to the question whether it is possible to put the tiles on the tile on the bathroom floor or even on the wall, rather affirmative. Of course, in the process will have to abide by a set of rules and recommendations, and the end result is almost always can be unpredictable, but in principle, it is possible to do this.

instagram viewer