Finishes the attic with his own hands, photo and design

Preliminary work before facing the attic

In the attic if you wish, you can turn even an ordinary attic with steep slopes, pulls up to the ceilings. For this will be enough to build a low wall on both sides. In this case, the original and practical solution would be inset ceiling windows and the decoration-carrier beams truss system.

Related article:

House with a loft: photos, projects, especially planning. Advantages and disadvantages of various features planning residential attic floor. Creating a project on their own.

If produce high quality insulation

and formed the attic floor finish, then it will get quite a few high-grade rooms. It is necessary to formulate a number of principles that should be followed when carrying out work on warming:

• rays must be perfectly protected from a variety of precipitation and wind. They must withstand a wide temperature differences;
• insulation of the roof is made not only within, but also outside. It provides a good guarantee that the freezing and drafts can be avoided even in the most severe winter;

Next analyze each stage of finishing details.

ceiling decoration, which is the floor of the attic

In order to properly make the floor in the attic, require the establishment of a sound-insulating layer inside overlap. any acoustic material may be used for this purpose. Not bad copes with this task mineral wool. Mattresses from it are laid between the joists, not forgetting previously spread out on their film. The thickness of mineral wool may be between 5 and 10 cm. Well suited expanded clay, granular Penoizol or polystyrene chips. These measures along with insulated floor in the attic.

On top of the joists should be laid subfloor. If the beams are located less than 40 cm from each other, then we can put them directly on the plywood, DSP or other similar sheet material. If the beam away, then you need to first put them on board (can be untrimmed) thickness not less than 3.5 cm. The main condition - the rough floor should not bend when walking. Already they screwed on the screws the same plywood.

Finish on the floor of the attic

Finishes the attic with his own hands (photo proof) involve the use of a wide variety of floor finish. You can use all of the same materials as in common rooms: laminate, linoleum, Carpet and even ceramic tile (if the bathroom or kitchen will be located in the attic).

For laying parquet or laminate previously on the floor need to put a special substrate, which will provide not only the softness of the floating floor, but will also provide additional sound insulation. Tiling device requires screed use with an reinforcing mesh.

Finishes the attic with his own hands, photo walls and ceilings

Partially or completely walled room is a mansard roof. If the house was originally built with an attic, then warming It should be carried out immediately after the construction of roof system. To this end, the bottom hem to rafters boards or plywood, and on top of them laid vapor barrier membrane.

It must be done properly by reading the packaging, which side it should be laid. On top of the membrane is placed insulation, attach it to the rafters and nailed slats crates under the roofing material. All this close windproof film and mounted the roof.

As a result, the roof slopes will have good thermal insulation. Alternatively, finish the attic with his own hands (photo will not slukavit) is made after the construction of the house. In this case, a heater inside sutured, and already on the wall it is made of plasterboard, plywood or other sheet material. Warming of the attic gable walls is similar.

Making attic gypsum boards

In conducting walls in the attic of plasterboard we win repeatedly, since it allows you to immediately align and insulate the walls, it is easy to handle and install, it can be issued by any finishing material, even wallpaper. In addition, the drywall can create various architectural "excesses" such as niches, arches and columns. attic finishing sheets GCR technology is no different from any other method of finishing facilities.

Finishing of wall and ceiling space

One meynstrimnyh directions in the design of the attic floor, is finishing his Lining. Although it is one of the oldest ways, he has not lost relevance in modern design. If you initially plan to sheathe the attic floor wood, you do not need to create the walls of plasterboard.

Suffice it to hem to rafters board ends close to each other. Even better, they have a tongue and groove, like sexual rail. Lining in this case can be attached directly to the wall, not erecting additional frame.

Technology cladding Lining

For some attachment of siding on the frame it is preferable to other options for finishing attic with his own hands. Photos of this process can be sequentially illustrate the procedure for carrying out all the works:

• We buy the lightest breed Lining, which include: maple, ash, fir, spruce. This visually enlarge the space slightly;
• we will need the rack 5-15 cm wide;
• We connect them between a ready tongue and groove;

Useful advice!To little to dilute the completely drab interior walls of the Lining, you can use the trim MDF panels. They create harmony in the interior, warmth and durability. Special effects bottom wall, which is decorated with the MDF coated cork and wood plinth and all kinds of rail is better to make slightly darker.

As we can see, there are many options for finishing attic with his own hands. Photos of many of them tell us what to do like we too are able to. The main thing here - to show imagination and accuracy. At the same time we must not forget about those recommendations that we gave you. It finishes in the attic will expand the territory to the bright and spacious private office, an excellent billiard room, exercise room or living room.

The interior design of the attic (video)

Finishing the attic (video)