How to remove the mounting foam frozen and fresh

How to get rid of frozen foam

If the foam has frozen before it is removed, then it takes a lot of time and effort to eliminate it. The simplest method is the mechanical .When looking for, than removing the mounting foam, often pay attention to the various sharp objects with which the composition is scraped off.

However, it is not always possible to remove the mounting foam mechanically. If the surface is easily damaged, then the process should be as gentle as possible. In this case, the stain from the mounting foam is moistened with with the dimexide and covered with a soft cloth impregnated with it. This antiseptic liquid should be purchased at the pharmacy.

After a few minutes, the foam becomes soft. It is easily removed with a stiff brush or blunt knife.

How to remove fresh foam from the surface?

If the mounting foam has not yet frozen, i.e. The polymerization process was not completed, then removing it from the surface is quite easy. First, the composition is removed with the with or with the knife. Of course, a small amount of material remains on the surface. It is cleaned with special fluid to flush mounting guns.

With this liquid, we wet the cloth and wipe a small area with the edge of the stained surface. Such a test is necessary to check how the paint, varnish or other coating reacts to sufficiently aggressive compositions. If the varnish is not washed off, and the paint has not changed color, then it is possible to remove the remaining foam.

Than to wash the mounting foam

Will help to remove the unattached mounting foam and other dissolving liquids .It can be acetone, white spirit, nail polish remover and a number of other solvents. You should act the same way as in the previous version. First, in a small area, the effect of the substance is checked. If everything is in order, then it can be applied on a large plot.

pre-heated oil will help to remove the mounting foam and .It is wetted with a rag or a sponge and the remains of an unattached composition are wiped off. The most important thing is that the oil is not absorbed in the surface, otherwise there will be ugly spots.

After the application of solvents, the treated areas are washed with with soapy water .It removes the residue of corrosive substances so that they do not damage the surface.

If the foam hit the tile, then vinegar is best for removing it. It removes fresh composition from the tiles easily and quickly.

We wipe the mounting foam from the floor

To remove the mounting foam from the surface of the flooring, various means can be used.

1. The with spatula, which has not yet been congealed, is cleaned with a dry sponge or with the solvent .For frozen foam, use a special cleaner.
2. Dimexide is a pharmacy disinfectant, it is a strong solvent. Easily softens the mounting foam.
3. Special agents that dissolve foam.
4. Water also helps remove the remnants of the mounting foam. It softens the composition and it is relatively easy to clean.

How to remove the foam from the clothes?

If the mounting foam has got on the clothes, then the probability that it can be removed is not high. The substance adheres perfectly to all surfaces. In the case of the fabric, it penetrates between the fibers, which further complicates the process. Try to clean the clothes yet you can, but do not use solvents that contain acetone. They damage the tissue. If you choose how to remove the mounting foam from your clothes, you can pay attention to the following options.

1. Treat with solvents for mounting foam .One species copes with the fresh composition, and for the hardened foam, another is required. First, large parts of the foam are removed from the tissue. They are collected or cut. Then apply a cleaner. If the foam is fresh, then it is removed immediately, if it is hardened, then you must wait a quarter of an hour before softening. After cleaning, the clothes are washed or wiped with a damp cloth.
2. The desired effect can be obtained with gasoline or ayt-spirit in combination with stain remover for clothing. First place with a mounting foam is treated with dissolving substances. Some time should wait until the foam becomes soft. Then a stain remover is applied. After all these stages clothes should be washed.
3. with low temperature can be applied to the foam. To do this, the contaminated clothing is put in a plastic bag and placed in the freezer. There, the foam freezes and is easily detached from the fabric with a knife. There remains its small amount that has penetrated between the fibers. Removing these residues will help a nail polish remover or some kind of solvent. You must choose a means that will not damage the fabric and will not lead to its fading. After such treatment, clothes are washed.

Foam mounting on the skin: what to do?

Cleaning hands is much easier than removing the mounting foam from the door or from the clothes. First, the foam to the skin sticks worse. Secondly, the skin has an upper layer of keratinizing cells, which are painlessly peeled together with particles of adherent composition.

Methods for removing the foam from the hands are as follows:

• If the mounting foam does not have time to solidify , then it is scrubbed with scrubs, brushes, ie.mechanically. To simplify the process, you can use dissolving substances that are relatively safe for the skin. It can be gasoline, a cleaner for removing varnish or acetone. The most safe option is a solution of salt. Conventional table salt is diluted in water and hands are dropped into this solution. When the foam becomes wet, it is wiped off with a hard sponge.
• If the foam on the hands of freezes , then you can get rid of it only mechanically. The hardened compound is simply wiped off the surface of the skin. Sometimes it takes several days.

Than to clear a mounting foam. Video instruction