Gidrouroven: instructions on how to make the building a water level of the hands, videos and photos

How to quickly gather gidrouroven for construction

X

Table of contents

  • 1 All you need to know about the water level
    • 1.1 where to apply
    • 1.2 How to apply
    • 1.3 Making the tool to work without assistants
    • 1.4 A few words about the spirit level
  • 2 To summarize
Water level - it is a useful tool which can be bought, but you can do it yourself

Water level - it is a useful tool which can be bought, but you can do it yourself

It is necessary to make a flat floor or ceiling, but you do not know how to align the beacons on the horizon? I'll tell you how to do gidrouroven their hands and how to use it correctly. And at the same time look at the available types of levels, presented in the store.

All you need to know about the water level

Gidrouroven - a tool with which you can determine how the relative position of distant objects corresponds to the horizontal plane. The operation of such devices is based on the principle of communicating vessels.

Atmospheric pressure acts equally on the one liquid and the other side of the hose, so the liquid level will be the same even if one side of the hose will be below the other

Atmospheric pressure acts equally on the one liquid and the other side of the hose, so the liquid level will be the same even if one side of the hose will be below the other

By gidrourovnya category includes construction spirit level. Despite the fact that there are no communicating vessels, compliance with the horizontal plane is also determined by a liquid.

In the photo - building spirit level, which will not only determine the skew plane, but also serve as a good ruler

In the photo - building spirit level, which will not only determine the skew plane, but also serve as a good ruler

The disadvantage of this device is its short length and that it does not bend. That is, unlike the flexible hose, filled with liquid, this tool is not designed to work at a great distance.

Despite the simplicity of the device device, the level of hydraulic construction can not produce itself, and buy in factory performance in any hardware store

Despite the simplicity of the device device, the level of hydraulic construction can not produce itself, and buy in factory performance in any hardware store

Name Price spring 2017
TULIPS TOOLS II13-880 370-400 rub.
Bison "Master" (length 20 m) 400-440 rub.
Topex (length 15 m) 700-750 rub.

Gidrouroven prefabricated - a transparent hose to the graduated flask. The flask was attached plugs, to liquid does not spill into the flooded unit. The average length of the tube is 10 to 20 meters. For normal circulation of fluid used 6-8 mm diameter hose.

Choosing building gidrouroven, we give preference to models with removable bulbs, as in case of damage the tubing ends can be cut and then re-attach the flask.

where to apply

illustrations Methods of Use
table_pic_att14918448164 Spacing level floor screed. With a flask at the desired level from the floor, with another bulb can make a layout for the screed.

Given the size flasks, the minimum indentation screed from the original base should be 100mm.

table_pic_att14918448165 Marking the position of radiators. A hose filled with water, will show at what distance from the floor need to hang radiators for example have already installed heating equipment.
table_pic_att14918448176 perimeter markings for mounting ceiling. If there is no laser level, the perimeter of the ceiling can be marked with a hose filled with water.

The accuracy of such marking will be as high as if it was used laser level.

How to apply

illustrations Description of action
table_pic_att14918448197 fill the tube. Tint water in the bucket in the extreme case it is possible to use a soap solution, as long as there was no bubbles.

We lower end of the tube in the bucket, the other end of the tube falls below the level of the bucket. With the "suck" of the free end of the tube and wait for the water will flow.

table_pic_att14918448208 Prepare tool to work. Raise up both ends of the tube so that the water level inside the tube did not reach the edge of about 5 cm.
table_pic_att14918448219 How to use gidrourovnya:
  • Putting a one end of the tube to one side surface and make a mark;
  • The second end of the tube to transfer the desired position and is also applied to the surface.

At both ends of the pipe fluid will be at one point.

Described gidrouroven has a significant drawback - it is impossible to use it alone. But there is a more technical version of the communicating vessels, which can be used without assistants.

Making the tool to work without assistants

illustrations Description of action
table_pic_att149184482210 What you need to assemble the device. You will need:
  • 10-liter bucket;
  • Roulette unnecessary;
  • rake length of 1 m;
  • transparent hose length of 10 meters;
  • ties or tape.
table_pic_att149184482411 Make a timeline. By putting a meter rail roulette and squandered at both ends with tape to get more range.

Starting from the edge where the marker 1 m primatyvaem end of the hose. Squander hose across the line of adhesive tape.

table_pic_att149184483012 Fill tool water. The free end of the tube is omitted in a bucket of water. The tube does not pop up, tie it shut to the handle of a bucket, but it does not pinch.

"Suck" the water and wait until it will pour without bubbles.

table_pic_att149184483213 we use gidrouroven. To measure the height of the water level in the bucket. In this case, the reference point - 23.5 cm.

Now to measure the height of the brick. We set the scale of it and see to what point the water comes. In our case it is 17 cm.

Now, from the reference point 23.5 cm subtracting the resulting number 17 cm and 6.5 cm obtain. For clarity, the usual measure bricks measuring tape and see that the number is the same.

table_pic_att149184483314 instructionwith gidrourovnya. Suppose you need to fight off the perimeter of the tie. Put a bucket near the wall on the ground leveled. When the filled tube is poured into a bucket of water so that its upper mark us reached the desired level.

Now we have to take the free end of the tube to the desired length and mark the wall proper height.

For greater efficiency measurements can be used not one but two pipes spaced from each other in different directions. That is, you can simultaneously make a layout for the tie from the two walls by placing a bucket in the corner.

A few words about the spirit level

Spirit level with the Dutch translated as "water meter". But if the previous tool, the principle of communicating vessels was involved, then the device applies a capsule with a liquid, in which the air bubble moves freely.

To make the device more functional capsule fill is not water, and alcohol, which freezes at temperatures below zero

To make the device more functional capsule fill is not water, and alcohol, which freezes at temperatures below zero

The water level is designed as a line or regulations, and the capsule is located in the center:

  • When the line lies on a horizontal flat surface, the vial is located strictly in the middle of the capsule;
  • If the line deviates from the horizontal, the bubble is displaced from the center.

The device can be equipped with not one, but two capsules. In this case, one capsule disposed in a horizontal plane, and the other - to the vertical. Thus, one can determine the time of horizontal and vertical surfaces.

To summarize

Now that you know how to properly use gidrourovnya to determine the flatness of the plane relative to the horizon. Moreover, you will be able to collect gidrouroven themselves. Also I recommend to viewing the video in this article, and if you have questions or need clarification, write about it in the comments.