How to glue the film for the greenhouse: fix it on the arcs of the greenhouse, cover the fastening properly, tighten it as better

Before bonding to the film, it is necessary to study expert advice and watch instructional videos When attaching the film it is important to tighten it and hold to it are not carried away in a strong wind. There are several ways of its fastening, each of them can be carried out independently, without the help of a specialist. The fastening of the material can be done to wooden slats, metal or plastic pipes.

Experts advise how to pull the film on the greenhouse

at first glance, it appears that the coating film frame greenhouse - a simple affair. But this work requires certain efforts and compliance with certain rules. If the width of the film coincides with the width of the greenhouse - excellent, because for the laying will not need to glue the material. To correctly measure the required length for the coating, you need to roll the film roll across the entire frame - from one end to the other, close these parts of the structure and add a gap of 30 cm on each side. This is needed to fix the film to the ground.

If the width of the material is not enough, it can be glued together overlapping tape or hot gluing( soldering iron, iron).

If the greenhouse is large, the need for film tensioning 2-3 people

tensioned foil in calm advise warm weather, heat from the material can be stretched, resulting in sagging, and the film has shrink properties at low temperatures, Which leads to cracking.

bottom film which remained on the allowance, wooden slats fastened to a foundation or steel reinforcement is wrapped in a film and buried in the ground. After all the preparation work, you can start fixing the material to the arches of the greenhouse.

There are a lot of ways of fixing the film. The main task is to ensure that the material adheres well to the frame. If it is blown strongly by the wind, the film either breaks, or the hothouse completely remains uncoated.

polyethylene Soldering how greenhouse cover film

When a film stretching frame in the greenhouse, and sometimes the width of the material is not enough to cover the entire area of ​​the structure. In this case, the film can be glued together with adhesive tape, but it is better to solder it and get a fairly large piece of coating.

For bonding uses several simple techniques:

1. cutting material webs decomposed on the flat surface of "pile" - against each other. On the edges lay a sheet of parchment or newspaper. Go through the paper with an iron with a sufficiently high temperature. At the joints should form a seam. It is important to ensure that the polyethylene does not completely melt.
2. edges of the cut material necessary to squeeze between the special metal plates. At the edges that look at 1 cm from the clamp, walk through the hot soldering iron until a seam is obtained.
3. Special glue - he must have frost-resistant, moisture repellent properties and to be environmentally friendly as much as possible, because in the greenhouses will be grown vegetables.

If the film is much older and has damage to the solder it makes no sense to

choosing any method of soldering, it is best to first practice on small scraps, choose the optimum temperature and pressure to create a weld.

By choosing any of these methods, you can get a large piece of material that can easily be covered with a greenhouse.

Thus, you can sew another film case, which you can replace the old one in case of damage. After hiding the greenhouse with film, you need to determine how to attach it to the frame.

Fixing of a film on a greenhouse: ways of packing of a material

A dacha or a farmer who wants to grow vegetables in the cold season or sprout seedlings can build a film greenhouse on his own. Manufacturing and installation can take a certain time, while a number of nuances need to be taken into account.

It is important to know from what material the frame of the future greenhouse will be made. Wooden bars and metal-plastic arches do not need special preparation, iron - you need to wrap it with a cloth or cover with several layers of paint.

First of all, you need to decide which film will cover the frame of the greenhouse. Covering temporary hotbeds is no different from covering long-term greenhouses. The choice is great enough - polyethylene film, PVC, multi-layer and reinforced film. Each of them has its own distinctive characteristics and different lifespan.

After stretching the film in the greenhouse it should sprinkle ground

Iron tends to be heated and in contact with the film can melt it.

Depending on the shape of the greenhouse - arched or gable, you can choose the most appropriate option for attaching the film to the frame.

methods of laying the material in the film greenhouses:

1. Mounting rail - the easiest, but least harmless way. With this fastening, the rail is fixed on the nails to the wooden frame, thereby piercing the material. To prevent large ruptures, a strip of linoleum can be laid between the film and the wooden strip.
2. If the frame of the greenhouse is made of metal-plastic pipes, the film can be attached to them using special clips.
3. Wrapping mesh - first the frame is covered by a film, then top tensioned mesh, pressing the film covering. With this method of fixing the film can not be damaged, but it can move to the side in strong winds. Then the stretching procedure should be repeated anew.
4. Similarly, you can wrap the film with a rope or a tight rope. Lock it on one side, throw it on the other and back - forming a zigzag.
5. Fastening through the eyelets. Eyelets - a hole in a thick film, reinforced with metal rings. Through this holes, the elastic cord is stretched and the film coating is strengthened.

When laying the film on the frame is not a strong pull on it - at varying temperatures film may be deformed. If the stretch is poor, it may be sagging during precipitation in the form of rain or snow.

Pin greenhouse film on the arcs by means of clamps and clips

clips used for fixing film greenhouses, which frame is made of metal pipes or fittings. The diameter of the pipe can be 25, 32 or 60 mm. Tension the film on the frame is not very convenient, but they are fastened very easily with the help of special clamps. They put on a pipe, grab a plastic film and press it against the arcs.

Similar clips can be found in any hardware store. But if they are not available or there is no opportunity to purchase them, you can make such clamps with your own hands. To do this, take a plastic pipe and cut pieces into 4-5 cm long. Then on each tube it is necessary to cut off the side part - the cut must be of such a size that it can be attached to the arc of the greenhouse.

There are special clamps to quickly and easily secure the film to the frame greenhouses

is important to sharpen the edges of tubes to sharp corners without tearing the film when mounting.

Similarly, you can make clips from a rubber hose, but the rubber has the property of cracking, so this method is short-lived.

You can also use large sized office binders to attach the film to the frame. They can be attached to the frame, if the diameter of the pipes allows.

How to glue a film for a greenhouse( video)

When laying a film on the arc of a greenhouse it is important to remember that the quality of the tension depends on the density of the material. It is best to avoid using nails and other fasteners that can damage the coating. In case this happens, a crack or hole can be glued with special glue or a hot soldering iron.