To grow tomatoes properly, it takes a lot of effort, from planting to a competent garter. Every minute moment can affect the yield, quality and even how soon the ripening will begin. Tying tomatoes is necessary in order to promote abundant fruit bearing, because if the branches are broken, this will stop the flow of useful substances to the fruits, and at all can cause rot, oviposition and dying off of the branch. Every gardener should familiarize himself with how the garter is performed, at what time, and how to avoid mistakes. Only in this case it is possible to achieve an excellent result.
- Recommendations: how best to tie up tomatoes in the greenhouse
- quality garter tomatoes in the greenhouse polycarbonate
- Methods garter tall tomatoes in the greenhouse
- How to use the device for a garter of tomatoes in the greenhouse
- Garter tomato in(Video)
- Examples: how to tie a tomato in a greenhouse( photo)
Recommendations: how to tie tomatoes in a greenhouse
The dandelion of tomatoes is the process by which stems and branches are attached to a special support using ropes, fabric strip, plastic stems. Tie the tomatoes immediately, after the steps have been taken and the ovaries are formed. As the bush of tomatoes will gradually increase, it is required to tie up several times.
. Besides this, do not think that the plant requires additional fastening only if it is too high, becauseAbsolutely all bushes require this procedure.
Not only the stems themselves are tied up, but also the branches on which the fruits are laid. In special cases, it may be necessary to strengthen each branch, if the fruiting is very good. It is strictly forbidden to twist the branches of tomatoes too strong nodes or pulling the trunk to the support. It is desirable, with respect to the growth of the bush, simply to make the dressing to a higher level.
If you correctly wade a garter, you can get a number of advantages:
- Excellent tied tomato bushes, allows you to feed and water without getting a solution on the foliage, which the culture categorically does not tolerate.
- Tomatoes that hang, rather than lying on the ground or other branches, are practically shielded from the appearance of a problem such as late blight and sloughing.
- Collecting fruit from tied bush is much easier.
- Heavy branches will not be damaged even with too many fruits on them.
- The plant will have no deficiency in incoming oxygen and light.
In a polycarbonate greenhouse, tying is not difficult, and for this you can use a support or a special dressing material. As for the canvas, cotton fabric, kapron tights, cut knee socks will do. After the season is over, do not throw away the dressing material, since if it is washed, it will be suitable for the next year, which will eliminate the problem with its preparation and significantly shorten the time.
It is better not to use such material variants, for garter, like string, fishing line, thin string, wire. Thin and too hard material can cause damage and, accordingly, breaking the branches.
Quality garters of tomatoes in a greenhouse made of polycarbonate
There are a variety of methods for tywing tomatoes in a polycarbonate greenhouse, but the most popular are the garter of each bush for individual support, fastening to a wire frame, a linear garter, a garter rigging, and vertical trellis.
Often tied up on an individual support, as it is suitable for greenhouses and polycarbonate and conventional film.
A support in the form of:
- Wooden stakes;
- Plastic or metal pipes;
- Thick rods.
The support is installed near each bush, and in height it must be selected in accordance with the height of the adult bush. The stem is wrapped around a strip of tissue and fixed on the support. The method is perfect for small and medium sized tomato bushes. For high use it is not advisable, since the support can fall along with the bush.
Methods of fastening the tall tomatoes in the greenhouse
Basically, for tall tomato varieties, the garter method is used for the wire frame. It can be used for many types of tomatoes, but it is worth it to prepare a metal grid with large cells that wraps around plants and slightly digs into the ground.
This stem will be supported by the stems of tomatoes, as well as branches that already have fruits. If necessary, the structure can be dismantled and moved to another location. The method has a significant drawback, since it does not allow a quick and simple collection of ripened tomatoes. The option of linear tying excludes the use of stakes and is considered the most economical way to grow a large number of tomatoes.
The essence is:
- In the installation of 2 metal pipes on 2 sides of the greenhouse;
- They will then have a rope installed;
- Plants are tied at the same distance from each other;
- It is possible to fix the bushes with large and heavy bunches.
Trellis girdle is mainly used for planting high-yielding and low-growing varieties. The method consists in installing thick metal poles and pulling the rope every 30 cm in height. As a result, a kind of net is formed, on which branches of bushes are fastened with plastic clips. It is quite possible to pass tomatoes through the net. Very convenient to grow on trellises bushes spreading type, in which fruiting stepson. Fastening bushes is very convenient, and it is possible to use trellises made of wood or plastic.
Important!The design should be fixed as tightly as possible to prevent the entire structure from falling and, consequently, damage to the crop.
If you plan to grow tomatoes in a year-round greenhouse, then you should set up vertical trellises, this will support a tall tomato variety with side lashes cut off. On the surface of the roof of the greenhouse, a rope must be fixed and from each tomato it must have its own anchorage. This way the bunches will be carefully fixed even with a large number of fruits.
The supporting rope should not have a small thickness, but also softness and strength, so that it supports the branches of tomatoes, and does not cause them to break and fall. Some gardeners prefer to use a plastic mesh stretched between poles instead of rope trellis.
How to use a device for gartering tomatoes in a greenhouse
In order for tomatoes to fully justify all the works enclosed in them, you will need seed selection, competent planting, proper care, careful and accurate appearance of the garter. Typically, which option for tying up the culture will be used, depends on personal preferences, the availability of materials of a certain kind, a plant variety that affects fruiting, speed maturation and even the growth of the hive, the size and capacity of the greenhouse, how the cultivation will be carried out, for example, All the year round or seasonally. Choose the methods you need to be as safe and very effective.
Garter tomato in polycarbonate greenhouse( video)
It is quite possible to install a fastening of bushes that will allow using the structure every year without deconstructing it. The main thing is to follow the recommendations and to properly install the structure so that it does not fall and does not lead to breakage of bushes and damage to the harvest.