How to turn on the boiler: use the water heater sparingly, switch off, use the correct ariston, electricity

If all rights are guaranteed long life and correct operation of the boiler Proper use of the boiler causes the durability of the device and its smooth operation. You need to know how to turn it on correctly to start the system, and how to turn it off to save power.

How to turn the water heater "Thermex": features of the model

installation of the water heater "Thermex" carried out by professionals, and its inclusion would have to sNima his hands. But you need to know exactly how to properly perform this action, so that the device does not fail. The flow-through boiler is switched on in the usual way: the air is drained, hot water is blocked, the necessary settings are set, and the system is turned on. The main difference between a flowing boiler and a time-accumulating water heating system. The first option takes only 5-15 seconds, and the second - 2,5-3 hours.

Before turning on the water heater "Thermex" to the network, it must be filled with water

Stages plugging the heater:

1. overlain shut-off valve on the hot gutter.
2. The air is descending. First, a tap with hot water opens, and then with a cold one. The air is determined by a torn stream, when the water is intermittent, and the tap itself can "snort".
3. When the water starts to go quietly, all the valves are closed. The boiler is connected to the mains.
4. Before the connection itself, the required temperature must be adjusted.

The performance of the boiler is checked on the panel. Indicators, temperature are checked. If everything is in order, then after 15-20 minutes the temperature will begin to rise.

A separate socket with ground is used to connect the boiler.

But there are cases when the connection is problematic enough and the water heater does not turn on. In this case, first check the electricity networks, sockets and other elements. Also, the cause may be a broken cable, which is checked with a tester.

How to use water heater "Ariston»

Especial difference in connecting storage systems do not. The "Ariston" boiler is similar to the connection of other devices. Let's consider each step in more detail.

In all models, the boiler of the brand "Ariston" provided a drain valve for removing accumulated sediment within the reservoir

sequence connecting the water heater "Ariston»:

1. necessary to close the hot water shut-off valve.
2. It is necessary to open the valve in the place of installation of the unit and to drain water from it. After that, close the tap.
3. Air is drained from the water heater. To do this, the inlet valve is first opened( marked in blue), then the hot water tap( marked in red).After the air is released, when the jet becomes flat, it is necessary to close the hot water tap.
4. The cold water valve does not close, as its supply is controlled automatically.
5. The boiler is connected to the mains and the temperature parameters are adjusted.

After completion of work, it is necessary to check the operation of the unit. The temperature starts to increase on the turned on panel. If this does not happen, the water heater has been connected incorrectly or the boiler has failed.

Useful advices on how to use the

boiler When the boiler was first switched on, it must be given time to warm up the water to the maximum temperature. Open the tap on the mixer and check for leaks. If they are not available, you can safely use the water heater.

Instructions for use of the boiler regulate the proper operation of the appliance. It is important to comply with all of its regulations.

After switching on the device, you need to adjust the required temperature. Usually these parameters are determined by three modes: 35, 55 and 75 degrees. In some models, you can set the temperature at 10 degrees. This mode is called "anti-frost".

Every 2 years is necessary to clean the boiler tank from scale, and it is important to check the status of PETN

Tips to use the boiler:

1. not need to connect the water heater when there is no water in the tank. This will cause a failure of the heater. The safety valve is equipped with a check valve, which must be checked once a year.
2. Setting temperature depends on the wishes of the owner, but once in two weeks must include the maximum temperature for a couple of hours. This will prevent the proliferation of pathogenic microflora.
3. Cold water must be filtered using a strainer. Depending on the characteristics of the water, additional cleaning plants are installed.

Flowing water heaters are also easy to operate. Switching on the appliance starts with unscrewing the tap with hot water. The temperature is regulated by pressure.

Recommendations how to use sparingly boiler

Boiler fairly expensive device. Every owner will know about this when it comes time to pay for electricity. That is why there are a number of recommendations for saving electricity.

Save can be programmed using the boiler controllers, carrying hot water after a certain time

budgetary rules use the boiler:

1. not need to turn off the water heater, if you constantly need hot water. When the boiler keeps a constant temperature, then less energy is left than on its heating each time first.
2. If hot water is needed less frequently than once a day, it is best to turn off the boiler.
3. Some models offer economy mode.

But most importantly, you need to save water itself. It is not necessary that it flowed unnecessarily. Heating is fast enough, and closing the tap for several minutes during the procedures will save you money.

How to start the boiler immediately after installation( video)

The boiler in the apartment is installed - an irreplaceable thing. It does not matter if the water heater is running or cumulative, since the start-up is not fundamentally different. At the same time, it is important to use the device economically and observe all the operating instructions.