The ceiling in the bath: with their own hands, a step-by-step guide on how to make walls correctly and what, insulation, video

Ceiling device requires special attention. Qualitative material, choice of the board and correctly executed stages will allow to effectively and quickly cope with this task. As for the erection of blocks, treat with insulation and plating with due diligence.

what do the ceiling in the bath: boards for covering ceilings

bearing wood structures should be strong and durable. Species, or rather, wood species, which will be used for this purpose - larch, cedar, needles, aspen. For mounting the ceiling gangway, it is advised to use a grooved or planed board, its thickness - not less than 50 mm - this will allow the ceiling design to be made suitable for the attic.

When you have to choose the boards yourself, look carefully at the material for knots, various cracks and other deformations.

Well, of course, the work of processing woodwork with antiseptics precedes the work. So you better protect the wood from spontaneous combustion, rotting and spoilage by insects.

types of ceilings for bath

today mainly in the construction of the bath are selected three types of ceilings - plank, podshivnoy, panel.

ceilings What you can do:

• grazing. It is recommended to install such a ceiling in a small bath house, with a span of no more than two and a half meters. The boards must be mounted directly on the walls in the bath, the joint in the joint. It turns out a shield, which should be covered with a vapor barrier layer and a heat-insulating layer. Then you need to fill a simple soft insulation( peat, for example), and close it with a croaker. But this method has a disadvantage, its installation is incompatible with the attic. Or rather - moving around the attic.
• Panel. This ceiling mount need of pre-prepared sheets, of which have formed the following types of construction: two supporting beams inner finishing + + vapor barrier, insulation, waterproofing( cake) + outer gangway( there is only the part of the attic).The laying of this ceiling is economical, often it uses lumber cuttings.
• This is the ceiling in which the beams are lined with lining. Then you need to lay all the insulation layers. After the waterproofing, the ceiling is lined with planks from the attic.

In the latter case, everything can be built with their own hands, but the purchase of materials will cost a pretty penny.

insulation and waterproofing ceiling baths

Waterproofing - a device standard, it is necessary, because the condensation during the use of the bath. Waterproofing protects the insulation and the roof.

The best material, according to many experts, is impregnated insulation. She has a high coefficient of protection.

Waterproofing can have a transparent and translucent structure, it is not difficult to apply. A good layer creates a thick clay, however, it must first be mixed with sawdust.

A good alternative is parchment and a film, full waterproofing organizes foil waterproofing.

Isospan is often used as a vapor barrier.

Than to warm a ceiling and walls of a bath

The thermal insulation of a ceiling can be made by various materials.

It can be:

• Expanded clay;
• Mineral wool;
• Basalit;
• Clay and sawdust.

Warming with clay is a popular way, one can, so to speak, make high-quality insulation of the ceiling. From the side of the attic, the boards are treated with a liquid clay-sand mixture. Well, the ceiling is filled in the bath with shavings, sawdust and leaves.

Ceiling in the bath: step by step instruction manual

Bath is not just a floor, roof and walls. This is a great design for health and relaxation, made with a special frame technology. Much attention is paid to everything - convenience in the dressing room, quality of the frame, the area of ​​washing( washing), the presence of a shower room.

An example of the arrangement of a bath can be the installation of a false ceiling:

• The bearing walls are mounted on the walls of the structure, the cross section is 5 and 15 cm. A frame is also created around the chimney from the bars.
• From the inside the ceiling is lined with a lining, or shpuntovkoy. Mounting the skin to the beams, the fasteners are located not in the center of the boards, but in the grooves.
• On the casing you need to raise the vapor barrier, to the beams it is attached with a stapler. Isolation should go to the walls of centimeters by 15 precisely. Places of joints will fix aluminum film on an adhesive basis.
• Thermal insulation is inserted between the beams. This layer covers the waterproofing.
• The flooring is laid from the top, the boards are fastened with nails with a wide bonnet directly to the bearing beams.

If you use foam or mineral wool as a heater, the assembly of the false ceiling is done according to the reverse scenario: first you install beams, and already an external deck is attached to them, and a heater is placed between the beams. To the beams, a special stapler is fastened with a vapor barrier, the slats are mounted to the bars, and the lining is fixed on the bottom.

Design baths: advice on the arrangement

Beautiful ceilings in the room no one surprises, so why the aesthetics and beauty of the ceiling surface in the sauna and sauna is often considered something amazing. The rough ceiling can be sewn, treated with antiseptics beforehand. The highlight is lighting - authentic, in eco-style.

Also with a brickwork, you can find a decorative solution, respectively, to present logs and overlap. Even ventilation today is decorated decoratively. By the way, ventilation is very important - because of it, or rather, because of its insufficient quality, the ceiling in the dressing room often sweats.

In a wooden bath or foam bath, you can step-by-step make a high-quality ceiling, so that in any office it is comfortable. Why not explore all the options for erecting the ceiling to choose the best, and financially, too.

Successful construction!