To properly pokleit wallpaper butt, it is necessary to use special tools and high-quality adhesive And the most simple cotton, more expensive types of wallpaper can be glued in two ways - overlapping and butt. Lapping is usually glued at the corners and in hard-to-reach places, where it is difficult to do otherwise. Of course, the consumption of material will increase, but it is more likely that the wallpaper will not be peeled off. In other cases, the wallpaper is usually glued with the formation of joints.
-
- As wallpaper glue butt:
- technology How to adjust drawing on the wallpaper properly
- If bubbles appear on the wallpaper after gluing, what to do
- Which glue is needed for joints
- wallpaper How to hang wallpaper correctlybutt( video)
- process wallpapering butt( photo)
As wallpaper glue butt:
technology is most important that were not visible gaps between the joints. Such a fit is necessary, otherwise the gluing will not be aesthetic. If you paste wallpaper, not observing the accuracy in the joints, there will be a feeling of careless sticking. And this, of course, is not correct.
Step-by-step technology of pasting wallpaper:
- Roll cut into canvases, adding to the stripes of 5 cm more, then cut off;
- Cloth spread with glue from the center to the edges, bend the strip in half and let it soak for a couple of minutes with glue;
- Use a plumbline to draw a vertical line so that the first strip goes smoothly, then you will navigate it - why often there is a bevel, just the same, because of an imperfectly even glued first strip;
- Wallpaper is usually glued from the window;
- Extra pieces of a knife are cut only after the strip has dried, do not rush to remove excess immediately;
- Smooth the wallpaper with a special spatula, if the glue comes out from under the canvas, remove it with a rag;
- Next attach the canvas previous level without spades, if you have to customize the wallpaper on the image, increasing the complexity of the operation( in this case, always take on the tube longer, as some pieces will fall because of the adjustment of the figure);
- The joint should be inconspicuous, after the strip is glued, go through a special suture roller that fixes the joints.
It is recommended to use ASD59 ASD as a clerical cutter to cut the protruding remains. Try to observe the optimal sticking mode. The temperature in the room should not be lower than 20 degrees, do not allow drafts, because of which the wallpaper more than once will have to be glued.
How to fit the picture on the wallpaper correctly
This option, as a non-matching pattern, of course, is not considered. No matter how complicated the process seems, be sure to customize the drawing. Remember that there will be more waste. It depends on how large the picture on the wallpaper. On German wallpaper, almost always the step of the drawing is indicated on the roll.
Always look at how to paste wallpaper more profitably and economically, often you have to take pieces from different rolls. On both sides of the piece leave allowances of a few centimeters to make the drawing perfectly.
to wallpaper looked harmonious and aesthetically pleasing, it is necessary to very accurately adjust the image
Joints have to be adjusted as precisely as possible, then the surface will look, as people say, one carpet.
If bubbles appear on the wallpaper after gluing what to do
You can paste past wallpaper, sometimes you have to glue the joints twice, but how to fix the situation if there are bubbles on the wallpaper?
How to remove bubbles from the wallpaper:
- If vinyl wallpaper, take a plastic spatula, if non-woven - a rubber roller if paper - soft cloth. From the surface of the material, drive away excess glue, wipe the strip with a dry rag.
- If the strips have dried up, and the bubbles still remain, and there are many of them, there's nothing to be done, the wallpaper will have to be repainted. If there are not enough blisters, arm yourself with a syringe. Pierce the bubble with a needle in the center, squeeze the air out of it, draw a glue into the syringe, fill the hole. Then iron the wallpaper with the right tool.
When forming bubbles on wallpaper, use a certain spatula( depending on the type of wallpaper) and repair defects
With bulky blisters, the incision can be made with a smooth blade at the bottom of the swollen area. Then with glue from the syringe fill the voids, smooth the surface from top to bottom, removing excess glue.
How to avoid the appearance of bubbles
The main thing is to take a suitable glue. It should match the wallpaper, for thin paper wallpaper does not fit a strong adhesive compound, weighting the canvas.
The room temperature is ideal - 20-23 degrees. If the weather is hot, install water containers in the room, and the windows can be covered with cloth so that the wallpaper does not dry out too quickly.
In order to prevent the formation of bubbles, adhere to the temperature regime and use an adhesive suitable for the type of wallpaper selected.
Do not open windows and doors during the pasting during the day. Glue stir also strictly according to the instructions, you do not need to do it too intensively, if that is not indicated on the package. Intensive mixing saturates the glue with oxygen, which leads to the formation of the same bubbles.
What glue is needed for the joints of the
wallpaper Today, in any large construction market, you can buy special glue for wallpaper joints. From traditional adhesive compositions it will be different. Its consistency will be more dense, since the composition contains a polyvinyl acetate emulsion. But there are compounds without this component.
Some owners prefer to glue the joints to the familiar all PVA glue. But for the given purposes he all the same is not focused.
Read the instructions on the adhesive package so as not to inflict an excessive amount of
Do not apply a lot of glue, do not let it get on the front side of the wallpaper. In turn, carefully consider the bands themselves. It happens that, for example, dark wallpaper in one place can have a light joint( just burned out, stored incorrectly, the wallpaper is taken straight from the storefront).And this can not be eliminated, except that do not glue this strip.
How to properly glue wallpaper to butt( video)
Wallpaper gluing, of course, busy. Do not save on materials, tools, observe the temperature regime, pay special attention to the joints, and this process will give you even pleasure, you will be proud of the results of your work.
wallpapering process butt( photo)
