Gypsum boards are very popular. All because the material allows you to hide flaws and uneven walls. GCR are large and even in themselves, so you can cover a large area in a short period of time. You can work on any surface. In addition, you can install a frame and attach sheets to it. And between the wall and gypsum plasterboard put insulation material. The frame is not always necessary. In a small apartment every meter is on the account, so drywall should be used on glue.
- Composition of the mixture and how to glue the plasterboard to the brick wall
- How to fasten the plasterboard to the brick wall: preparatory work
- How to dry the brick wall without installing the frame
- Installing the drywall on the brick wall using the frame method
- Examples of brick or plasterboard walls( video)
Composition of the mixture and how to glue the plasterboard to the brick wall
There are certain methods fixedGypsum plasterboard to the wall. But each of them requires special preparation of materials and tools, as well as the surface itself. To choose the right one, you should think carefully and weigh it.
Depending on the condition of the wall, the adhesive composition is also determined.
The most economical and recommended by the experts composition is glue on a gypsum or cement basis. Before starting to work, you need to think about which glue will be suitable for work, if it is a frameless method of skinning. As a rule, there are several options.
- Adhesive for an even wall;
- Means for pasting drywall on a brick wall;
- Adhesive for surface with large irregularities.
It's hard, especially if it's a brick wall. When the surface is flat, then the work goes smoothly. But in any case there will always be small differences between the bricks in the seams area. Therefore, the glue will lie unevenly on the wall. Thus, there is a possibility that the plasterboard sheet will also fall unreliable. Before you can sheat the brick wall with sheets, the surface should be prepared.
How to attach a drywall to a brick wall: preparatory work
Before fixing gipsokartonnye sheets, the surface should be prepared. Since the glue will lie unevenly on it, the sheets themselves will remain weak. Experts recommend using useful tips to prepare a brick wall for the installation of drywall.
- Using a plumb line, measure how much the vertical wall is. If there are differences more than 20 mm, it is required to lay drywall. Strips up to a width of 120 mm. Depending on where the shortcomings were found, the bands are also installed. They will perform the role of beacons when it comes to fastening large sheets.
- Straight lines can be replaced by rectangles. They are cut from the same sheet of drywall. The size can range from 100 to 150 mm. Elements are glued to the wall, observing between them a distance of up to 250 mm. Everything depends on the detected irregularities.
Some people try to attach a gypsum cardboard sheet with mounting foam or polymer mastic. But this is an unfortunate decision, as the material itself will need a lot. And it is not a fact that such fastening will be reliable.
If the gypsum board is fixed to the wall with glue, it must be additionally fixed with special dowels.
The fastening of gypsum boards to the brick wall also depends on the masonry material. The same goes for the foam block and concrete. For example, to a red brick or to foam concrete blocks sheets can be fastened with any glue, the connection will be reliable
How to dry a brick wall with a gypsum board without installing the frame
Before you get started, you need to prepare the appropriate materials and tools. Decorating a brick wall with plasterboard can be done by own hands or ask for help from a specialist. The process is not difficult, but care must be taken.
Tools and materials:
- Plain and notched trowel;Tanks to dilute water and glue;
- Drill and additional mixing head;
- Wooden block;
- Reinforcing tape.
The whole process involves several stages of work. It all starts with the fact that it is necessary to treat the brick wall with a primer. Adhesive composition is prepared before laying the plates, since it can harden for an hour.
Preparing the glue follows exactly following the instructions, observing the specified proportions.
Adhesive solution is applied in small breasts. First along the entire perimeter, then process the center of the sheet. Between the piles should not be a long distance, enough 25 cm. The finished sheet should be placed on the lining and pressed against the wall. Special level to check that the surface was flat. If necessary, fit, using a wooden bar, light strokes on the sheet. The solution will dry, you can put reinforcing tape on the joints and apply a layer of glue. The final stage will be a skin and a primer.
Installation of drywall on a brick wall using the
This option is more suitable when the walls are very uneven. Therefore, experts recommend the use of gypsum boards, a thickness of 12 mm or more. As for the frame, it can be metal or wooden. But it is better, of course wooden, it is environmentally friendly, cheaper, and also more convenient to use.
Tools and materials:
- Screws and screws;
- Corners metallic;
Fastening technology begins with the installation of two racks in a horizontal position on the wall, then on the ceiling and on the floor. It is necessary to align them vertically. Between them should be installed vertical elements, which are equal in width to the drywall sheet.
To improve the heat and sound insulation properties of the structure will help heat insulator.
For fixing gipsokartonnyh sheets to the frame should be used screws or screws. Optimum length of them within 30 mm, it is recommended to observe a distance between them of 25 cm. As a rule, a small gap of 5 mm is left between the sheets. This is necessary for finishing the seams. It is necessary to understand that the skeleton method of wall covering reduces the useful space of the room.
Examples of brick or plasterboard walls( video)
Today many people prefer this material to cover the walls of the room from the inside. And it's not surprising, GKL is universal, they do not just hide the unevennesses and shortcomings of the brick wall, but also make it possible to realize various design solutions in reality. Drywall is also called dry plaster, it's easy to use in work. Moreover, the top gipsokartonnye plates do not necessarily finish, they can immediately paint or glue wallpaper. It is for such merits that most people choose the GKL for wall cladding.