Passing the chimney pipe through the ceiling: how to install and fix the gas, installation and cutting of the oven and air duct, fixing the corrugation and sewer

click fraud protection

The guarantee of safety and longevity of the house is provided with proper ceiling cutting for the chimney home security and longevity Collateral provided with proper cutting ceiling for the chimney There are many methods of installing air ducts and sewers. The assembly can be done in a horizontal or vertical plane. Before starting the installation work, you need to select the appropriate mount. The choice of method will depend on the shape and size of the main channel, through which air will flow. The main requirement for air ducts and pipes is the tightness of the structure.

Contents:
    • How to install the pipe through the ceiling: step by step instructions
    • What pipe mount to the ceiling reliable
    • gas pipe under the ceiling: how to properly install
    • Installation of the chimney through the ceiling with his hands
    • how to produce cutting furnacepipe on the ceiling
    • corrugations carry fastening to the ceiling
    • The tubes can be repaired in the ceiling
    • flue passage through the ceiling( video)

As set trUbu through the ceiling: step by step instruction

Before you start, you need to find the right place for fixing the pipe. Remember that the chimney should not be close to the bearing beams. It is desirable to make a schematic drawing. With its help you will be easier to navigate. After you have picked up a suitable place, you need to purchase a sandwich of pipes and fasteners.

The pipe through the ceiling must pass in a place safe from heat and do not come into contact with the bearing beams pipe must pass through the ceiling in a safe place by heating and not in contact with bearing beams

The installation pipes through the ceiling:

  1. First take plumb and raise it to the ceiling. Remember that its cargo should be located in the middle of the duct for the chimney.
  2. Note on the ceiling where the center of the pipe will pass.
  3. Use a ceiling box to mark holes in the ceiling. Then cut the slots with a chainsaw.
  4. Make holes on the roof. The greater the bias, the larger the gap will be.
  5. Secure the chimney pipe.
  6. If desired, cover the opening on the roof with a stainless steel sheet.

If the pipe will be located close to walls or partitions, it is advisable to install special protective screens on them. They are usually made of stainless steel or basalt cardboard.

Which pipe fastening to the ceiling is safer

There are two types of pipe fastening - horizontal and vertical. Horizontal fixation is applied somewhat less often. When using this method, fixing the blower is attached to the column by means of a special angle or brackets.

The horizontal fixing of the pipe is performed in the following order:

  • First, the duct passage is inspected.
  • Then on the wall you need to install special fasteners.
  • Next, gather all the details in the block. Do not forget to strengthen the clamps.
  • After that, it assembles the air duct. Use flange fasteners.
  • Attach the structural elements to the places where you made the preliminary marking.
  • Check the system for leaks.

If the column on which the systems are to be fixed is made in the form of a grid, an air duct must be installed between the braces. Before you start, do not forget to fix the nozzles.

There are two types of chimney ducts: vertical and horizontal there are two types for fixing the chimney pipe: vertical and horizontal

vertical ventilation Fitting Algorithm:

  1. first counting is carried out.
  2. After this, you need to fix the brackets. You also need to install the elevator and the console.
  3. Then you need to install the umbrella.
  4. Next, you need to assemble the details of the structure and install the fasteners.
  5. Assemble the entire structure and check for leaks.

Gas pipe in the ceiling: how to install

A hot gas pipe is more dangerous than a sewer. Therefore, when installing it, you must strictly follow a number of recommendations. If you build a gas pipe yourself, then make it from acid-proof stainless steel. Such chimneys do not deform under the influence of toxic substances.

It's no secret that harmful gas condensate can accumulate in gas pipes. To prevent water from entering the boiler, a specialized collection of harmful condensate must be installed in the system. In addition, it is desirable to insulate part of the gas pipe, which is on the street.

When installing a gas pipe, it is necessary to observe safety precautions When installing the gas pipe, it is necessary to observe the safety precautions

When installing the gas pipe, consider the following nuances:

  • Isolate the pipe only with non-combustible materials.
  • It is strictly forbidden to make the paneling of the structure by cardboard, as this will make it more difficult to detect a leak.
  • Before installation, make sure that the pipe is sealed.

Installing the chimney through the ceiling with your own hands

Before you start, you need to make a special passage of the chimney pipe. To do this, you need to mark out the chimney outlet. In this case, you need to take into account the angle of the roof. During marking, note that the distance between the outer walls of the pipe surface and the edges of the floor structure must be at least 140 mm.

Before starting work, be sure to degrease all parts and remove the protective film. In addition, select the suitable material for insulation of pipes. Excellent fit fiberglass, mineral wool or asbestos.

To install the chimney, you need to make a marking for the outlet of the pipe For the installation of a chimney it is necessary to make a marking for the outlet of the pipe

The installation is carried out in the following order:

  1. In the marking areas, make holes for the passage of the pipe.
  2. Next, assemble the structure and secure it.
  3. After completing the installation, fill the slots with insulating material.
  4. If desired, you can install a heat shield made of stainless steel. Do not forget to install a fireproof insulation before beginning installation.

How to cut the chimney on the ceiling

Special attention is paid to cutting the chimney. What dimensions should a ceiling trim have?Remember that the thickness of the sandwich for thermal insulation should be at least 5-6 centimeters. The other parameters you must choose, taking into account the dimensions of the room in which the installation is made.

It is not desirable to use galvanized sheets for furnishing a bath or a warm room. This is due to the fact that this material emits toxic substances under the influence of high temperatures.

The chimney section is a galvanized box through which the pipe passes to the roof

The cutting procedure is as follows:

  1. First you need to install the box from the attic space.
  2. Then a stainless steel sheet must be attached to the box.
  3. Tighten the pipe with clamps.
  4. Then place the insulation layer in the hollow part of the case.

We fix the corrugation to the ceiling

It is best to fix the corrugations to the canvas with the help of special clips. They are staples made of plastic. Clips are fastened to the ceiling with simple dowels.

Sometimes in the apartment in parallel to each other are several cables. In this case, you can use special latches, which allow you to put together several clips.

Gofra is attached to the ceiling with special clips The corrugation is fastened to the ceiling with special clips

There are often cases where it is necessary to fasten clips of different sizes. In this case, you need to pay attention to the latches of the products.

There are 3 forms of latches for fixing the corrugations to the ceiling:

  • Latches protrusion-groove of the circular configuration.
  • Latches groove-protrusion with a round configuration.
  • Trapezoidal latch protrusion-groove.

Than it is possible to seal pipes in the ceiling

After the wiring and installation of the pipes, it is necessary to seal the cracks around the pipes. In order to properly correct the defect, you need to consider the type of ceiling.

For example, it is possible to seal a hole around a pipe in the ceiling, which is covered with plaster, with a mixture of joinery glue, chalk and tooth powder. This solution needs to be filled with holes, and the remains are cleaned with a hacksaw.

Filling the cracks around the pipes in the ceiling, account is taken of the material with which the ceiling is trimmed Completing the cracks around the pipes in the ceiling takes into account the material with which the ceiling is trimmed

When closing the pipe in a gypsum board ceiling, adhere to the following algorithm:

  1. First, insulate the hole. To do this, use the mounting foam.
  2. Cut out a strip of the necessary dimensions from a piece of plywood. Be sure to consider the diameter of the pipe.
  3. Secure the patch with screws.
  4. Top with putty.

Passing the chimney through the ceiling( video)

As you can see, it is not very difficult to produce a separate flue through the ceiling. The main thing is to make the right markup and find the right materials. Do not neglect the fire safety rules during operation. For pipe insulation, use only flame retardant materials. After installation, do not forget to install protective shields on the walls and eliminate defects that have formed around the pipe.



instagram viewer