Connecting the washing machine to the water supply and sewerage: how to connect it to water, to the water supply and to drain to the sewerage

After selecting the desired model of the washing machine and delivering it home, each owner of this equipment has the task of installing the new unit in the right place, and then connecting the machine to thecommunications.

The location of the machine should be considered well in advance of its acquisition. The most common and often used option is to put the technique in the bathroom. It is chosen in most cases. However, owners of tiny bathrooms often decide to install a typewriter in the kitchen. These options are approximately the same in complexity, as access to water and sanitation will be free in the bathroom and in the kitchen.

A much less common technique is installed in the hallway, since in this case it is required not only to allocate space for the machine, but also to derive communications, which can present difficulties. A compact machine can also be installed in the toilet, organizing a sink in the toilet.

Before taking on the connection of the washing machine to the communications, it is necessary to remove the packaging from the machinery and to remove the parts that kept the machine elements during transportation. It's about bars, bolts and other fasteners. Without removing them, you can not turn on the machine, as this can damage the drum and damage equipment.

After unscrewing the transport bolts, plastic plugs are inserted into the remaining holes after them. Do not forget to also add all the removed parts together in one place in case you have to contact the service.

To carry out this stage of installation of the washing machine, you should prepare flexible hoses and rubber gaskets to seal the connection points. Also, make sure that there is sufficient pressure in the pipes and the water purity.

The connection of the equipment to the water supply can be carried out in two ways:

Using a mixer into which the tee cuts. So you can quickly connect the equipment, but this method is often chosen as a temporary option. For this connection you will need a hose with a sufficient length. If the washing machine is installed in the same room as the toilet, the connection is possible to the hose through which water is fed into the drain tank.

With a separate valve. In the selected section of the water pipe, cut the thread, and then install the valve. In this case, both the crimp clutch and the fitting can be used. The water should then overlap after each washing process. With such a connection, it is especially important to install a protective mesh filter, which eliminates the ingress of mechanical particles into the machine. This filter should be cleaned regularly.

Visually this connection process, see in the following video.

The organization of the drainage of water from the washing machine is carried out taking into account such nuances:

If the technology does not have a special check valve, due to which the water passes only in one direction, it is necessary to take into account the installation level recommended by the manufacturer for the installation of the outlet hose. The maximum and minimum values ​​of the nozzle position limits should be consulted in the instructions.

The easiest way to organize a drain is to remove water into the bath. However, fixing the drain hose on the side of the bathtub is not considered the best option, since accidental displacement of the nozzle will result in water pouring onto the floor. It is best to organize a stationary drain, in which you will not worry about the hose and the risk of pouring the floor of the room.

For a more reliable drain to connect the drainage system of the unit to the sewage pipe, it is required to buy a separate siphon with a tap located above the knee, intended specifically for the washing machine. This variation of the connection will eliminate the risk of leakage and ensure a reliable discharge of water.

With a thickness of sewer pipes of more than 4-5 cm, it is possible to remove water from the washing machine directly into the sewage drain. In this case, you should always use a sealant.

When the work on the organization of the tap and water supply to the washing machine is completed, you need:

• Align the position of the technique using the level. Due to such actions, vibration during operation will be minimal. If the floor in the installation site is uneven, adjust the adjustable feet. Option with the use of supports from wood, linoleum or other materials is undesirable. After twisting the legs, you should check how stable the technique is. To do this, just click on the corners of the device from the top. If the machine tilts, continue adjusting the legs.
• Connect the machine to an electrical outlet. To do this, it is important to ground the switchboard, connect the device to a 3-wire type socket, and carefully insulate its ground wire.
• Switch on the test wash and evaluate the operation of the machine. It's okay if the tank is full of water at the right time and you will not see any leaks. Then the drum starts to rotate, and after 5-7 minutes after dialing the water will begin to heat up. After the end of the program, the water will drain, but there will be no extraneous sounds inside the equipment.