You can make a bath for a bath in several ways: mount a concrete font, make a wooden font, or purchase a plastic analog. Step by step the process of installing the font looks like this.
Step 1 - Choose the place where you need to mount the font
The area under the font is chosen depending on your preferences, and also it is necessary to take into account the proximity of the location of your bath. Fans of water procedures on the street will be most pleased if the font is in the open air. And when there is a lot of space inside the bathhouse, you can install the font inside.
According to the installation method, the fonts are classified into:
- recessed;
- glossy;
- open.
Step 2 - Define the font model
When creating a font for a bath room, you need to carefully approach and justify the choice of materials for a specific capacity model.
For the material used, the fonts can be:
- made of wood;
- concrete;
- made of plastic materials.
The font type and its design features are chosen based on the planned number of people who will simultaneously be immersed in the tank. Sometimes perform directly in the bosom of the capacity of specially provided seats, or simply make a "bathroom", in which it will be enough to dip several times. In the font it is possible to provide such additional functions as heating, hydromassage and others.
Step 3 - Preparing the platform for the installation of the font
- For the installation of a buried font, the following steps are envisaged:
- In accordance with the expected volumes of the font to be installed, it is necessary to dig a foundation pit.
- Formed and pre-cleaned trench is installed formwork.
- Then the rods of the reinforcement are laid and the concrete mixture is poured.
- A ready-made concrete base is laid with waterproofing.
The font from concrete
The font from concrete
By the way, what brand to choose concrete read here - what brand to choose concrete read here.
When it is planned to create a street font with simultaneous visits by two visitors, these events can be omitted.
Making a font from concrete takes a lot of time. First, dig a pit of the right size and clean it. A font is a container or a swimming pool, and its device can not do without an additional gravel-sand cushion. She will support the font as a support. Then the carpet is executed. Reinforcing concrete using a single-layer reinforcement, 8 mm in diameter, laying rods every 300 mm.
There are requirements for concrete used in the manufacture of bowls: its main qualities are water resistance and strength. So, for 1 m3 of concrete, crushed stone, cement, sand mixture, water, are taken, respectively: 1270 kg of crushed stone, 327 kg of cement, 625 kg of sand, 177 kg of water. Concrete in ready-made form can be bought at the factory. About the brands and properties of concrete read here.
Inside, the cup is sealed with an elastic membrane, followed by a special glue, lay a mosaic layer or ceramic tile. After that it is necessary to make grouting between the tiles. When installing a concrete font, timely connection of the supply and discharge of water must be made.
Wooden font
The tree is most often used for building fonts. From the chosen type of wood will depend on the effect of bathing.
- Cedar font contains essential oils, under the influence of which the skin becomes tender. Cedar increases the body's defenses due to the phytoncides contained in it.
- A font from oak wood has a calming effect, beneficially affecting the nervous system, as well as normalizing metabolism and accelerating regenerative processes on the skin.
- The deciduous font is able to normalize the pressure, the larch extract cleanses the pores. It is strong and durable.
Installation of a buried font
A dripped font from a tree
With the device of a deepened font, it is necessary to dig a foundation pit, clean it, erect fences, perform waterproofing and cladding. It is necessary to provide equipment for water supply and drainage. This option is quite expensive and time consuming.
Installation of an open font
A bath for a bath with your own hands
It is much easier to make an open font. To do this, you need to purchase a tank of the right amount of wood or polypropylene, install it on a solid foundation, connect it to the water supply and sewerage system and make an external finish. Recently, plastic fonts have become especially popular. Their installation is economical, and among the advantages one can single out practicality, durability, resistance to cracking, scratches, easy maintenance. High-tech polypropylene is 100% safe.
Plastic fonts are produced in various sizes and shapes. Fonts are completed with handrails, a seat, steps. To give the font an attractive appearance, the plastic containers are covered with a wooden apron. This is easiest to do by constructing a frame around the perimeter of the font, then securing the lining on it.
Mounting font fluff
Pouring font
This is the most economical type of font. A system is built into the wall, allowing you to tilt the pelvis or the tub of water by pulling on the rope. With the return of the tub to its original position, it again becomes filled with water. The flow of water is regulated by a special mechanism based on the float. Be sure to read about making a bath from a log.
