Contents of the article:
- 1 Wooden arbor with barbecue with own hands
- 2 Brick arbor with barbecue and BBQ
- 3 Homemade brick brazier. Step-by-step instruction
- 4 Brick barbecue at the dacha
- 5 Barbeque from the barrel with our own hands
- 6 Designs of gazebos with a brazier
Wooden arbor with a barbecue with our own hands
And first we will consider an example where a gazebo is made of sawn timber and a brazier is made of bricks. Immediately important advice: look for 6-meter timber and board. So there will be much less waste.
The first point of construction of a wooden arbor with a barbecue with your own hands is a choice of a place for building and its configuration. We take into account several important points:
- The entrance of into the house and the entrance to the gazebo should look at each other( so it is more convenient to carry out the table setting).
- We consider the rules fire safety .In the gazebo there will be a brazier with open fire, it is not necessary to erect it quite near the house.
Having defined the place, with the help of construction sand, we plan the contour of the foundation of the building. Our drawings of the arbor with barbecue assume that the gazebo will be octagonal, and the base under it will be in the form of a circle. The circle can be drawn using a pipe fixed in the ground and a rope tied to it.
In our case, the fertile soil layer had a thickness of only about 20 cm. Behind it was an excellent clayey soil. The construction is relatively small, therefore concrete bases are chosen as the base. The earth below them is better to choose and replace it with a sandy-gravel mixture. So you can level the height.
The material for the of the lower strapping is a bar with a section of 100x100 mm. In order not to be mistaken with the corners of the sawing, use a cardboard template. For the device of cross beams it is better to use a board 50x100.To make the harness reliable, it can be fastened with metal corners from the inside and out. Perfectly fit galvanized 105x105x90x2 mm at 135 and 90 degrees. Do not forget about the waterproofing layer of ruberoid between the pillars-bases and strapping.
Pavilions with barbecue with their own hands step-by-step photos
Paul in the gazebo is made of edging board 50x100.Immediately in the size of the right amount of material. On the front side of the board is better to plan the plane, and from the inside - to treat with antiseptic( preferably in several layers).We fix the floor with a screw and be sure to check the bottom bandage with a level again. 
It is more convenient to construct the top harness below. So it will be more convenient to carry out fitting of locks and lengths of rafters. As a material for the rafters and the upper strapping we use the same edging board 50x100.
In our case, a gazebo made of wood with a brazier own hands has an octagonal roof .Therefore, the rafters' lock will also be octagonal. We execute it from a bar 100х100.Pay attention to the placement of supports under the bar. For their installation, the octahedron had to be enlarged by means of boards with a thickness of 1.5 cm. 
Pavilions with a barbecue with their own hands. Photo
We proceed to the production of rafters .We perform a triangular cut at the bottom anchor point. We will use it as a lower lock. 
Like the upper bunch, the rafter is also assembled below. It will be easier to correct minor defects. 
Our gazebo and barbecue drawings provide for the installation of ten pillars .We make them from a bar 100х100.To make it easier to carry out their installation, the ends are cut off exactly at an angle of 90 degrees. We fix the poles to the base of the arbor with the help of corners 105x105x90x2 mm made of galvanized steel. We check the construction using the level. In our case, the installation of slopes was not needed. 
Gazebo with barbecue with your hands. Photo instruction
Now we are installing the rafter system and the upper strapping. For fastening we will need:
- Corners 70x70x55x2 mm 135 degrees;
- Corners 50х50х40х2 mm 90 degrees;
- Connecting plates 80х40х2 mm.
The roof is made of an inch board with a width of 100 and 150 mm. We make it close;start from the bottom and go around the circle to the top point of the building. For the convenience of marking, we use a cardboard template. With it, it's easier to mark the cut line. Each board is attached with two screws on each side. So the roof does not deform with time.
Do not forget about brazier made of brick with your own hands, which will be in the gazebo. Digging a hole under the base of the brazier depth of 40 cm. 
Formwork can be made of boards from transport pallets.
We cover the formwork with roofing felt .It is most convenient to do this with a construction stapler.
We lay the reinforcement( 10 mm class A3 bars) in the pit and the reinforcing mesh( d = 4, 100х100 mm).The foundation is filled with a mixture of cement and building sand in a ratio of 1 to 3. Ideally, the cement of the brand M 250 is ideal. In our case, 5 bags were needed.
After that, you can sew a pergola around the perimeter with a log simulator 45x146 mm. This will not only make the construction more attractive, but also add a stiffening framework.
Window sills are made from a board of 50x100 mm. To fix them, use the corners 50x50x40x2 mm. This part of the structure is not mandatory, but it will make the gazebo more comfortable for guests.
The bases of benches are made from a bar 50х50.We fix them at an angle to the walls with the help of corners 50x50x40x2 mm. This is the most durable and ergonomic design option.
The material for making the top of the benches is the grooved board 28x121 mm. To increase the strength, all the benches from the ends are connected by plates 80x40x2 mm.
For visual separation of the gazebo into two functional areas, the mangal side is decorated with wooden grill .For its production, a bar 15x20 mm is suitable.
Wooden gazebo with a barbecue with their own hands. Photo
At this work on the gazebo comes to an end and you can proceed to the construction barbecue bricks with your own hands.
The simpler the design, the easier it is to install it without errors. Therefore, it is better to use simple mangal drawings made of bricks without any frills. For the construction it will be required:
- Full-bodied red brick( 360 pcs.);
- Chamotte brick sand color( 90 pcs);
- Furnace mixture( 175 kg);
- Refractory mixture( 50 kg);
- Hot-rolled corner 40х40х4 mm( 7 meters);
- Galvanized oven umbrella.
For proper and accurate laying, it is necessary to fulfill a number of conditions. First, the solution should not be too thick. After installation, the brick must be easily adjusted by hand. Secondly, the ideal seam has a thickness of 3 mm. To this, it is necessary to strive to make the structure as durable as possible. Be sure to observe the same thickness of the seam throughout the structure. Third, you must not rush. Masonry is strictly level. On this step-by-step instruction of building a barbecue from a brick in a wooden gazebo can be completed. The whole sequence of masonry is well traced in photographs.
Brazier made of bricks in the gazebo. Photo
It remains only to cover the roof with bituminous tiles ( in the example used red shingles Shinglas) with the help of nails and building stapler, and also treat the gazebo with antiseptic and varnish. Antiseptic is applied in two layers. As a varnish glossy yachts are good.
Brick arbor with barbecue and barbecue
For those who have more masons in their hearts than carpenters, we offer a step-by-step instruction for the construction of a gazebo with barbecue made of bricks. We skip the stages of the search for a place and markup for the construction. All this was described above. Immediately go to work.
Construction of a brick pavilion with a barbecue. Step-by-step instruction
The brick structure will weigh a lot, so this time the foundation of the needs to be made solid and reinforced. After it is ready, we perform the masonry of the walls. 
The roofing system can be manufactured in exactly the same way as for a wooden pergola.
The first row is better laid out on a dry one.
We construct the drift .It will also be the basis for the barbecue and smokehouse. 
We continue to lay out the barbecue from the brick with our own hands. In turn, the firebox and countertop. If desired, you can arrange a niche for dishes.
Gazebo with barbecue yourself. Step-by-step photos of
For kazan we will need to install plate .Below is a variant with removable rings.
The base of the barbecue is ready. It's time to lay the countertop of fireclay bricks .
In the masonry, we must use the refractory mixture .
The next stage of construction of a gazebo with a brick barbecue with your own hands is the organization of the chimney and the formation of a channel for the smokehouse.
In our gazebo there will be Russian oven .We form for it under.
Each series must be reinforced with with wire.
We put the walls together. Accuracy of work is checked with the help of a level.
We finish the furnace .
In our case, the back wall of the furnace had to be pushed out.
The job will take quite some time, but progress will warm the soul.
We continue the construction of a barbecue made of brick by our own hands. We install the doors of the smokehouse. We finish the arches above the barbecue, hob and stove.
You can always assign the joints to the assistant.
A stainless steel mesh can be installed over the plate. In the future, it will be good to dry berries and mushrooms or dishes.
How to sew up a roof we already told above.
Gazebo with BBQ and barbecue. Photo by
On this step-by-step instruction for building a barbecue made of bricks comes to an end. Complex gazebo-barbecue is ready for surrender.
We bring water to the sink from behind the gazebo. For the winter it can be blocked.
The pipe is made of three-channel. So traction will be more stable.
Do not forget to cover all the masonry with a special impregnation with water-repellent effect .
It will take about a week to dry the building. On this, the construction of a gazebo with barbecue made of bricks is finished.
Homemade brick brazier. Step-by-step instruction
Mangal with their own hands. Drawings
Construction of a brick structure begins with the device of a solid foundation .Size is selected according to the size of the future barbecue.
We excavate the excavation at the selected place. On its edges we arrange a formwork( it can be made, for example, from boards from pallets).We pour concrete and reinforce the base. For complete hardening, it takes 1-2 weeks.
The is ready and you can start building a barbecue.
Drawing up drawings and plans is a useful thing. They will help to make an accurate estimate. Here is an approximate list of the required materials:
- Refractory bricks;
- Wire for masonry reinforcement;
- Sand and cement;
- Corners made of galvanized metal;
- Mesh or reinforcement rods;
- Lime.
Brazier of brick with their own hands. Photo
For preliminary calculations, arrange the bricks as they should be in the structure. Now it is clear where the stitches of the masonry will be and how many half and quarters of bricks will be needed.
The material absorbs moisture very well. Therefore, under the brick it is better to put waterproofing material .A pair of layers of roofing material is quite suitable.
It's time to start building a barbecue.
We prepare solution .To do this, mix cement, sand and slaked lime in a ratio of 1: 3: 0.25.On the resultant mixture will be laid out ahead of time prepared brick.
Masonry requires accuracy, attention and patience. We follow the seams, leveling the bricks by level.
The work technology requires laying the rows in the in a staggered manner .We focus on the first row, begin to lay from the corner, gradually filling the lateral space.
The brazier will be exposed to high temperatures. Therefore, it is better to put the second row with a clay-chamotte mixture.
To make the base under the frypot, it is necessary to install the rods between the opposite walls. The base of the furnace is mounted on them. For example, it can be a metal pallet.
The combustion process requires a constant supply of oxygen. To do this, in the laying of the furnace should leave a few gaps without a solution.
It remains to install the grate on rods or ledges( depends on the laying of the brazier) and choose a countertop.
Brick BBQ in the country house
Brick barbecue is an ideal option for a holiday village. This is a simple, convenient and reliable design that looks quite presentable.
We offer a detailed guide that will help even an inexperienced person in the construction to build such a structure in the shortest possible time.
The first stage of the work is the drawing up of detailed plan for .We give only an approximate scheme of construction. You must take into account the features of your own oven, its appearance, decor elements and so on.
Order of a brazier from a brick. Photo
Do not forget about the niche for firewood and coal. We calculate the place for a grill at a height of 65-70 cm from the ground. The stove should be placed lower by 10 cm.
Masonry bricks laying. Photo
After working with a pencil and ruler, you can move on to the practical part. As in the previous instructions, we begin with the foundation .
Under the barbecue, the same foundation as the brazier is suitable. This is a monolithic reinforced base. We excavate for him a pit depth of about half a meter. The bottom is covered with a layer of a mixture of gravel and rubble, watered and tamped.
We are installing the reinforcement, we form the frame. All that's left to do is formwork. Now you can move to the base of the base with concrete.
The foundation will need up to two weeks to completely dry. A little patience and you can move on to building a barbecue made of bricks.
Once the mortar has been prepared, it is possible to proceed to the masonry. We work slowly, according to the plan, laying out a row for a series. Constantly controlling the clutch by using a level.
First lay out pedestal oven-barbecue. It should not be too high( up to 70 cm).
We spread the second row, shifting the beginning of the tier to half a brick.
When you get to the oven, keep in mind that its depth must be at least three bricks, and the length must be at least six. We use fireclay bricks. On the ceilings, we fix the bars of the reinforcement.
The next stage is the construction of the chimney .If the scheme is made correctly, there will be no problems. When laying rows do not forget to make a "mantelpiece" on the back of the stove. It will greatly improve the draft in the pipe.
It only remains to add decor elements and clean the masonry from spray solutions and other construction debris. You can decorate a barbecue with paint applied to a brick. This will visually highlight the seams of the structure. In general, the design is already finished and can be used for its intended purpose.
Barbeque from the barrel with your own hands
If there is not much room on the site to arrange a gazebo with barbecue, it is always possible to make barbecue from a barrel with your own hands. For this we need:
- Metal barrel( preferably food);
- Paintwork materials( primer, paint);
- Brackets and hinges for fasteners;
- Chimney pipe.
We will install a barbecue for a special design. To make it we need pipes of small diameter( up to 50 mm) and boards. In the process of work, the following tools will be needed:
- Drill with a set of drills;
- Angle Grinding Machine;
- Measuring tape measure;
- Set of wrenches;
- Elements of fastening( yokes, bolts).
The preparation process is complete and you can start production. Cut into the side of our drums a rectangular hole, as shown in the photo. 
Now we need 6 pipes of small diameter. If they are concreted, then cut with the help of a Bulgarian. Of the 4 pipes we will make the legs of the structure, on which will stand the arbeku. BBQ from the barrel. Photo
The remaining two pipes are used to connect each pair of legs. To fix the structure we use bolts.
They will fix the position of our barrel. The length of the pipes is adjustable depending on the size of the barrel. As a result, a two-part construction should be obtained, each of which will consist of a pair of legs and a connecting pipe.
To connect two parts, you need to take 5 boards with a width of 150-200 mm. Four of them are used to fix the legs( on each side of two boards).One board is fixed at a height of 5-10 cm from the ground. The second should be just above the middle of the legs.
With the help of a drill, drill holes in the boards with a diameter equal to the diameter of the tube legs. We install the construction upside down and install the boards on the legs. In our case, to fix the boards at the desired level, bolt clamps were used. We turn the structure and boards into their place, not letting the legs of the structure part.
The last board is used to connect the upper tier of boards. This is the final touch in creating the foundation for barbecue. Now the barbecue from the barrel can be installed in its place.
The next stage of the work is the arrangement of the barrel. For cooking we need grating .To fix it inside the structure, we install a pair of brackets on each side with the help of bolts.
We remember about that piece of barrel, which we cut out at the very beginning. From it we will make a cover for a barbecue. Install the hinges and attach it back to the barrel. The grill arms will not allow the lid to tumble in when closing.
As a handle for the cover of the structure, you can use anything, for example, shovel shovel.
After installing the cover, carefully wash the barrel.
At the end of the barrel we drill the ventilation holes and master the bolt for them.
After that you can fix the chimney and paint the barbecue.
This step-by-step instruction for building a barbecue made of metal is coming to an end.
Projects of gazebos with brazier
Variations of wooden arbours with barbecue can be many. This version has an octagonal base and open walls on one side. There is enough light in the arbor, and benches and a table can be installed as needed.
You do not have to do the whole arbor from the brick. A feature of this gazebo are forged elements, from which the walls are made. The design looks easy and is naturally illuminated from all sides.
Even if there are not so many places on the site, it is always possible to build a canopy and decorate the walls with conventional boards. This version of the arbor with a brick brazier will fit in a very small area.
If time and resources allow, then on your site you can build a real work of construction art. A wooden gazebo with a brick brazier, a stove and a countertop, decorated with tiles, looks rich. Although its device will not take much time.
It takes a lot of space for a big family. It is better to do without the construction of bulky walls, and build a canopy and a brick brazier with a counter top under it on a reinforced durable foundation. A table furniture set is easily cleaned for the winter in a house or utility room.
Project of a gazebo with a barbecue. Photos of
Fireclay bricks - ideal for masonry furnaces .He does not hit hard on his pocket, but is strong enough and hardy to high temperatures. In advance, we harvest cement, building sand, and red clay. They are needed to create a solution. In time, fill the clay with water and hold it for a few days.
