A quality woodburner allows you to accurately and accurately store wood for the fireplace and stove. You can manufacture it at a low cost. To work you will need slats, plywood, film, soft roof, hinges, screws. Additionally, you need black and white paint on wood. The size of the considered woodburner is 164х164 cm, which can accommodate approximately 4.5 m3 of firewood.
Contents
- Assembling the side and rear walls
- Preparing the upper blocks, floor and roof
- Assembling the structure
- Building construction of the woodburner on the cottage with your own hands
Assembling the side and rear walls
It is not difficult to assemble the wood-burning tool with the proper manufacture of the sidewalls and the roof. The side parts have the same skeletons. The lower and right / left slats are perpendicular. The upper bar will be beveled. This design is optimal for creating an unusual roof, which will remove sediments.
A jumper is required between the left and right rails( in the center) to harden the final component. Reiki connected with self-tapping screws 5x100 mm.
In addition, the corners on the inside are reinforced with perforated metal plates.
The second sidewall is made similarly, but the bevel of the bar should be the opposite( not left-to-right, but vice versa).The rear wall is a mirror image of the side walls. We get 3 frames.
Preparation of upper blocks, floor and roof
The upper part of the side and rear walls is a wedge that repeats the shape of the prepared frame. You need to cut four identical pieces of plywood, as shown in the attached photos.
Then the obtained details with nails 2,2 x 45 mm nailed to three frames.
We still have another wedge of plywood. It is attached to the four-frame, which must be made from racks with self-tapping screws, and then fixed with metal plates. The shape and size of this frame will match the wedge. The frame itself will be located above the doors in the woodburner. So, fix the wedge with the help of nails to the last frame.
It turned out 3 identical frames and 1 frame, which will be located above the doors.
The prepared door frame, side, rear wall are painted with black paint, the slats( for styling the structure) are painted with white paint. But in order to understand how to build a wood-burning machine that is well protected from moisture, it is necessary to first study the features of the color composition. Usually, the tree is first treated with an antiseptic, and then the paint is applied in 2-3 layers.
White slats are stuffed on the walls.
Also from the rails, painted in white, the doors of the wood-burning tool are made.
Two triangles are prepared from plywood, which will become a roof. When composing, they must represent a square with a side equal to the length of the top of the wall. Both parts are painted black on one side.
A thin, but wide board assembles a latticed floor. The bottom of the floor, which will later be adjacent to the ground, is filled with a film to protect the tree from moisture. At this stage, all the elements of the construction are ready.
Now to learn how to make a wood-burning machine with your own hands, the assembly instructions below will help.
Assembling the
construction The completion of the construction of the woodburner takes place by assembling the previously harvested parts.
Install the walls in conical supports in the form of cones. Wedges are located near each corner of the knocked down floor( it is necessary to put them on the level).
Next to the side walls on both sides are attached beams
The walls are installed in metal supports.
The rear wall is located between them and is fixed to the bars in the supports.
Small temporary laths are attached to the side walls as supports to make it easier to mount the trapezoidal frame( it will be located above the doors);
Then the cutting parts of the beams are cut, which will interfere with the installation of the roof of the woodburner.
Two parts of the roof are fastened with hinges.
The roof is transferred to the frame( painted side and hinges inwards) and fixed along the perimeter.
The doors are installed on the hinges, the inner vertical lining is screwed( for tight fitting of the flaps).
Doors are installed on the doors.
Flexible shingles are installed on the roof, the remains of the coating are cut off, the skates are covered with protective crossings.
Using these instructions, it is not difficult to build a stylish and practical wood-burning machine in the country or near a private house.
Help in this and the attached photos, and useful videos. Before performing it, it is recommended to draw an exact drawing, according to which the work will be done.
