How to install a toilet bowl with your own hands?

Quite often such work as installing a toilet bowl with your own hands raises many questions, but with the right approach to the matter, strict adherence to the sequence of installation and the availability of an appropriate tool at hand, it is possible to fulfill it by everyone.

In any case, the installation of the toilet is divided into several separate stages of work.

As a rule, the scheme for connection to water and sewage is the same for all types of devices, and among themselves they can differ in the presence of all sorts of additional functions and type of installation.

In most cases, use floor-mounted devices, but recently the pendant type of these devices is gaining popularity, which are attached to the so-called installation.

As in the first case, installation of the hanging toilet bowl can be performed independently without any special problems.

toilet bowl Preparing for the installation and dismantling of the old

toilet bowl Although the floor type of devices is more familiar, more recently in homescan be found pendant.

Installation of a hanging toilet allows you to free up extra space in the toilet, and besides, it will be easier for housewives to clean up.

Before installing the toilet bowl on tiles or installing a hanging toilet bowl, you must acquire the appropriate tool, and also dismantle the old device.

For this purpose it is recommended to disinfect the old device and all its components with a special means, for example, bleach or whiteness.

Further it is necessary to completely cut off the supply of water from the water pipe to the apartment and drain the remaining water from the tank.

All work is best done in protective gloves and glasses to prevent the risk of injury.

Further it will be necessary to disconnect all hoses and connections of water supply, including from the drain tank. All these manipulations must be done with the release of water into the sewage system.

If the device is attached to the floor with screws, they must be unscrewed.

In the event that the device is planted on cement under the tile, then it will be necessary to break the floor with a perforator or sledgehammer.

After this, it is necessary to dismantle the connection of the toilet bowl to the sewer pipe. All work should be done carefully, so as not to damage the connection points.

When the old device is left aside, the joints should be thoroughly cleaned and treated with a sealant-type compound.

After dismantling the old device and before installing the toilet on the tile, you should prepare the base itself.

Of course, the old mount can be suitable for a new device, but do not count on it.

In order to prevent the toilet bowl from rolling off during its operation, it is necessary to make holes in the floor for fixing.

Video:

To do this, you should choose the best place in the toilet where the new device will fit, and its drain will reach the sewage pipe.

Also before starting the installation of the toilet, it is necessary to check it for cracks and defects, as well as completeness.

Installing a new

floor toilet To ensure that the installation of the toilet is done correctly, it is best to make a step-by-step work plan.

Detailed and correct scheme will make it possible not to get confused and alternately perform the installation of each element. As a rule, the instruction for installing the toilet bowl comes with the product.

Independent installation of the toilet starts with a thorough cleaning of all the necks of the supply pipes, after which they are covered with improvised material.

Hidden and concealed pipes are to be cleaned and must be mounted with a small outlet.

Further installation of the corrugation on the toilet, after which it is placed on the place where it will stand.

After that, under the bottom of the product, you need to place a gasket, which should be included in the corresponding kit.

Video:

The next step is to place the device on the place where it will stand, while carefully checking it for evenness, stability, as well as the possibility of hidden connection of the toilet bowl and the drain tank to all communications.

Use the marker to place the exact location on the floor, in addition, you need to mark the fixing points of the screws.

The device should be moved to the side, then using a perforator to drill the corresponding holes for fastening to the floor.

Then in these technical holes for each dowel is placed a wooden chop, a gasket is installed and a sealant is applied.

The sealant must be applied to the lower part of the device, which ensures its attachment to the floor.

Next, you should carefully and as precisely as possible install the device so that it is not at an oblique angle.

After this, the joint between the pipe and the toilet outlet should be treated with a sealant.

Now the toilet bowl has to be installed, and it is connected to all relevant communications.

For these purposes, you will need a sealant, flexible pipes and, accordingly, a corrugated hose.

Video:

Typically, the sewer pipe is connected to the device itself at an oblique angle through the corrugated hose, and sealant should be used to seal the joints.

The device itself needs to be connected to the outlet of the tank, which, in turn, is connected to a water pipe via a flexible hose.

After this, it remains only to check its operation and tightness of all connections.

Installation of a new

suspended hose Recently, the installation of a wall toilet that is attached to a special installation and allows to save space, which is especially important for small rooms, is gaining popularity.

These models imply the installation of a flush cask of concealed execution. They are strong enough, reliable, and in addition installation of a hanging toilet bowl with their own hands can be performed very easily.

The scheme of its installation is slightly more complicated than for a floor-standing device, however it will not be difficult to understand it.

Installation of the drain tank, which is subsequently hidden behind the wall, is done after the installation.

To install a device of this type, you must select the correct location, which will be in the immediate vicinity of the necessary communications.

In addition, it should be responsible for choosing the installation, which will be attached using an attachment to the walls and the floor.

Video:

Installation of the suspended toilet bowl begins with the installation of the installation, for which it must be attached to the floor and to the walls with the help of an attachable mount.

In general, an installation is a special metal frame. Virtually all installations are universal and suitable for most toilets.

When installing the installation, carefully check its evenness to prevent installation at an oblique angle.

Directly behind the installation, the drain tank is mounted in such a way that a branch pipe from it goes out at an oblique angle, which will later be connected to the toilet outlet.

After installing the installation, determine the water supply to the tank. You can choose the top or side version, then you need to connect it with the water pipe and toilet outlet.

Do it better with a plastic pipe.

The further installation of the hinged toilet bowl involves connecting it to the sewerage system, which, as a rule, is located at an oblique angle.

Next, you should think about the place where the panel will be mounted, with which you can control the release of water directly into the toilet itself.

Most of these panels are produced of one type - a binder - and fit almost all models of toilets.

After this, it is necessary to check the working capacity of the toilet bowl and the tightness of all connections, as further the installation of the wall is carried out, which will hide behind all its main parts.

After the wall and the lining layer completely dry out, the toilet is assembled by hand in a specially designated place.

It only remains to properly fix the panel with the drain button.

In most cases, the installation of a built-in toilet bowl, as well as an attachment device, can be performed independently without any special difficulties.

In both cases, the principle of work is similar and requires only strict compliance with the relevant instructions.

Video:

In any case, all connections must be carefully sealed, both the supply of water to the drain tank and the device itself to the sewage system, which is usually performed at an oblique angle.

This device must also be rigidly attached to the base of the wall or floor in order to prevent it from rolling and possibly falling.