Install the door lock interior doors: simple instruction

Standard locks are installed on interior doors, often for various reasons, be replaced. In addition, the finished fabric may be sold without a locking mechanism. Install the door lock - quite a difficult operation which requires an understanding of the device structure and working knowledge of nuances. The main factor determining the mounting features, is a kind of locking mechanism.

Installation of the lock on the door, select the type of locking mechanism

Design features are a major factor by which all classified locking devices used in interior webs. Consider the most popular devices to be installed in interior doors.

Latch (normal). This type of locking devices has the greatest distribution. Conventional latch used in interior paintings everywhere. Installation of the lock on the interior doors in this case is complex, it often attracts buyers. The feature of this device is that its construction includes a cylinder and a locking tab, with a special mechanism. Most often, these locks are implemented complete with handle. Thus, during installation to avoid errors, you need to read the instructions, which will answer the question of how to insert the handle in the interior doors.

Latch lock. The mechanisms that belong to this group are improved modification of previous variations of locking devices. In their design there is another element - a clamp. Its function is to hold the lock in the closed position. For interior doors such products fit perfectly.

Helpful information! Today you can find two types of latches, equipped with a lock: push-button and lever. For use in the home it is recommended to pay attention to the second option.

Mortise mechanism. Is the second in popularity among the castles interior doors. Installation in painting requires precision and care. Tapping devices are reliable and have a long service life. They are most often used for doors for personal offices and bedrooms. Unlike the previous types of these devices are opened by the key.

There are two types of tie mechanisms. The first option provides for the possibility of unlocking the doors on both sides (key-switch). In the second case, a combination that consists of key and turntables. This situation requires a separate inset handles in interior doors. How to perform this operation? For this purpose there is a special step by step instructions.

Consignment Castle. From the viewpoint of mounting such an option is most appropriate. However, overhead devices do not comply with modern safety standards. They can easily be put out of action by means of mechanical action.

Magnetic lock. The cost of these devices is higher than the price of conventional varieties of locking mechanisms. Their main advantage - quiet operation. That is why they are most often mounted on interior doors that are meant for bedrooms and children's rooms. Independently it is difficult to embed the castle in the interior doors. Price setting mechanisms depends on the magnetic characteristics of their design and type of door.

Lever device. Such devices are capable of providing good protection facilities. They are opened by a key and is used not only for the interior, but also for the input of paintings.

Installation of the lock on the door: flat and round device

Most often, the interior doors are fitted with locks that are more suited for operation in such conditions. These include flat and round mechanisms that differ from other forms of housing.

Flat interior locking devices are expensive. Their self-installation is accompanied by certain difficulties caused by the construction. However, such devices have one major advantage: they provide a high degree of protection against intrusion.

It should be noted an important feature of planar mechanisms: their installation weakens the door and the box. Before embedding the lock on the wooden door, you must set its compatibility with the web. Experts recommend to mount the flat products to cash in the door. Fabrics made from MDF, are not suitable for full installation planar mechanisms. They tend to crash a shortened version of the devices.

Helpful information!When mounting the door in a plane mechanism, made of MDF, it is necessary to consider that the tongues thickness should not be greater than 15 mm. Also in this case, the restriction applies to the end trim lock. Its width should not exceed 24 mm.

Round locking mechanisms are the best option for installation in the home. Therefore, they are found most often in the interior doors. It is not necessary to have special skills and abilities to carry out the installation of the lock in a wooden door. The main advantage of such devices - is compatible with any type of blades. In most cases, such mechanisms are used for the two variants of handles: falevye and knobs. The second type of products considered to be the most appropriate. Handles, knobs are recommended for installation in the home, as they are reliable and convenient.

Install the door lock interior doors: the necessary tools

To independently carry out the installation of the locking mechanism, it is necessary to prepare the appropriate tools. Installation of such devices does not require a large number of appliances and fixtures. The minimum set includes the following elements:

• crayon (marking for execution);
• tape measure;
• drill;
• screwdriver;
• Construction knife;
• chisels (10 and 20 mm);
• set of drills;
• masking tape.

Before installation, it is recommended to study the step by step instructions that will help you understand how to set the lock on the interior doors. It is worth noting that at the present time the market can meet the special sets, by which made tie-locking mechanisms in the webs made of different materials.

Kits for tapping locking devices usually comprise down drill, an indicator section which is 22 mm. This item is not suitable for organizing holes for the latch. In this case, use a chisel.

Box in the castle interior doors: the preparatory stage

The end result of self-assembly locking mechanism depends upon many factors. First of all on the degree of complexity of the installation is influenced by the type of door and lock design. Experts advise make preliminary drawing device. It should contain information on the location of future holes required for latching elements, handles and so on. D.

Note! If replacement of the old with a new mechanism, then it is recommended to read the instructions that will help you understand, how to disassemble the lock interior door with handle.

The more detailed drawing was made, the less likely the assumption of certain installation errors. Before starting the installation, you must make preparations for the door assembly. Preparatory step includes counting of the web. This is the way to allow embedding in interior doors lock correctly.

The first thing to determine the height of the castle above the floor. The standard amount by which the locking mechanisms are located interior webs is 1 m. If desired, to reduce or increase the distance from the floor 10 cm. Price setting in the interior doors of the castle is in the range from 1000 to 2500 rubles. The final cost depends on the type of lock and the nature of the work. Repair of locking mechanisms can cost about 1500 rubles.

After determining the desired height the device must seal the space, in which will be assembling, masking tape. Most often, complete with shut-offs are sold ready-made template that allows you to perform precise layout for a particular model. It must be applied to the face and the flat surface of the door.

How to insert the lock into the interior doors: without marking stencil

Mark all necessary points at which holes will be made for the installation of fastening elements is possible without applying the pattern. To do this, there is an instruction, which is necessary to pay attention to. The marking is done with a pencil or chalk.

Primarily required from the floor to measure the distance of 1 m. The desired point is performed horizontal mark. Next, draw a vertical line. The point of intersection of the two lines is the center of the locking mechanism assembly. Preparatory phase in the sidebar of the castle interior doors with their hands require special care. After partitioning the space in which is disposed a locking device, a determination points corresponding latch holes (on the face), and the door handle.

Then you need to make the body of the locking mechanism to the lines and carry the mark of the lower edge of the device. Next, you need to dissolve strips. The distance in this case corresponds to the thickness of the lock. Once the wiring layout is performed two parallel lines, which must be perpendicular to the horizontal lines at a distance of 5 cm.

Note!Accuracy of measurement affects the correctness of installation of the lock and handle in the interior doors. Errors in the markup lead to various problems that hinder the normal operation of the locking device. The lock is mounted at the end face of the door leaf. It is necessary to outline the central point clearly.

Next you need to perform a layout position, which will be located in the latch and handle. After that, the markup response openings are located on the door frame.

How to embed the castle of the wooden door: the organization of the holes for the handle and lock mechanism

The next stage, which follows the layout of the door leaf, includes a number of holes for the handle and locking mechanism of the device. This process is also divided into several stages.

First, you need to prepare a tool that will be used for holes. The easiest way to perform this work with the help of the screwdriver and the special nozzle (crown of the tree). The hole for the locking mechanism of the device is produced on a flat surface of the door leaf. Moreover, you should first make a hole on the outside and then the inside. Such a course of action to avoid damage to the electronic screwdriver.

The crown is used to organize the core holes and a pen. Installation on the door locking mechanism is made using another nozzle - pen drill. It applies to the openings for the latch on the front side of the web. It is important to remember that the drill bit must be immersed in a timber at a right angle.

Then it is necessary to remove the instrument and by means of the knife construction to remove the outer layer of timber in accordance with the tagged lines. After that, through the need to organize a chisel groove crossbar. Its depth must not exceed the width of the frame crossbar. After installing the latch and its fixing by means of screws.

Box in the castle interior doors: Cutter for installation

The easiest way to carry out the installation of the locking mechanism provides for the use of the cutter. Fraser is a vertical machine, which has a small size and is fairly easy to use. To make installation of the lock in of interior fabric using a milling device, you must first remove the door from its hinges and set it perpendicular to the floor (on one side).

Next, you need to perform measurements and to set the mark corresponding to the location of the tab mechanism. The next stage of the installation with their hands in the interior doors of the castle is the transfer of device parameters to the web. To do this, fasten the lock to the door surface and cut around his body pencil.

Note!In order to exclude the possibility of making mistakes, it is recommended to study the video, which will help to answer the question of how to embed the castle interior doors. Videos and photos allow us to study all the nuances of the process in more detail.

Then, on the side of the web must derive straight lines. After that, with the help of the machine you need to perform a recess for the lock. The next step involves changing the nozzle on the milling machine and performing a lock slot for housing. Precise execution of these instructions helps to organize competently opening of the locking mechanism. To verify proper operation, it is required to check the device to the appropriate place for it.

Related article:

Lock for interior doors: how to choose a reliable and durable mechanism

Variety of devices for interior doors. Locks with a latch, magnetic, electronic. Mortise and coupling devices. Tips on selection and correct installation.

How to Install a lock in the interior doors without using a cutter? A seat for the locking mechanism and can be prepared without using a special apparatus. For this work can be useful and ordinary hand tools. It is important to remember that this method is not suitable in all cases. For example, the lock assembly of the latch is not possible without the use of milling equipment.

Installing the locking mechanism with the larva: step by step guide

Mechanisms, which include the core (larva) are used in those cases where the web is already equipped with the door handle. Such locking devices are rectangular in shape. Features of the construction of these devices have an impact on the degree of difficulty of installation. A person who does not have special skills in this area, it is recommended to consider very carefully the mounting instructions.

Installing the door handle on interior doors in this case it is not required. This simplifies the workflow. In the first place for mounting the locking mechanism with the larvae need to select the location of the device. Its can be positioned above or below the handle.

After you select a location for installation, it is required to strictly follow the installation instructions. First, you need to partition, this should draw a center line on the end face of the web. Further, the standard procedure is carried out, which is to move shapes lock the door. Then you need to make the axial line of the hole having a small distance from each other. With the drill removes excess material web (between holes). As a result, it should be able to slot the locking mechanism.

The most suitable area for installation of the device is under the door handle. Installation on interior doors can be achieved with the use of hand-held devices. The next step is to insert the installation mechanism larva into the opening that was made earlier. Fixation device manufactured using self-tapping screws.

Then required to mark the perimeter of the key-plate. For this work fit the knife construction. Using a chisel is made removing excess material. Well the insert should exactly match its size.

Note!If you plan to not only the installation of the lock, but the door handle and installation, you must read the instructions for its replacement.

After marking and sampling keyhole plate should be attached to the locking device and transfer the web surface contours of the larvae to the door. It is important to remember that this operation is carried out both on the outside and on the inside of the door. With the drill hole must perform for sekretki (larvae). For a free location is recommended mechanism to make it more widely within the recess than sekretki sizes.

At the last stage, the installation of a mechanism in a prepared nest under it. The locking device is fixed by means of screws. After installation, you want to check the correct operation of the device. At the end, you can decorate the surface of the door lock in the place of installation of special plates, which are fixed with screws.

How to embed the castle interior doors: the installation of a mate

To the door was locked, must be installed on the door frame mounting plate with an opening for the lock tongue. Installation of this item is fairly simple.

Price Mortise lock in interior doors depends on the type of mechanism. In any case, self-installation saves finances. The first thing to note the zone in which the mounting plate will be located. This site has the appropriate voltage latch lock. To do this, close the door leaf and apply ludku two lines indicating the boundaries of the latch. It is also recommended to perform measurement of distance between the upper boundary and the angle of the latch of the door leaf. The parameters obtained should be moved to the doorway.

Before starting the work it is necessary to check the accuracy of installation of the door handle with a latch or other type of locking mechanism. The device must be located exactly. Otherwise there may be problems with opening and closing of the door leaf.

Helpful information!As an alternative to the mechanisms that have a standard lock, you can purchase a magnetic lock. It is characterized by operational reliability and quiet operation. Installing the magnetic lock in the interior doors has its own features, but subject to its instructions may perform a novice.

After partitioning the area corresponding to the latch mounting plate should be attached to the door frame. There is one important rule that will help to implement the installation of a competent response element. If the item is recessed in ludki material, then the need to delineate its contour both on the inner and on the outer side. In turn, if the mounting plate is located directly on the surface, then the marking should be limited to the internal circuit.

After partitioning plate spacing is necessary to perform the opening latch and the lock products (screws). Then you can install the mating straps. Upon completion of the work required to close the door and check the size of the gap. once clearance is eliminated very simple, if necessary. All you need to do - to bend the lock tongue on the mounting plate.

How to disassemble the door handle interior door round type

A method of dismantling round doorknobs for interior webs may vary depending on the structural features of the hardware. The most convenient are the products that have two tightening screws. In this case, perform a self-dismantling easier. To do this, unscrew the locking elements and to remove the mechanism.

However, there are situations that require a lot of effort. Mechanisms are more complicated from the constructive point of view, be dismantled in stages. On modern interior doors are quite common around the details, equipped with a button and a variety of decorative elements. The function of these pads is hiding the mounting screws. How to remove the handle from the interior door in this case?

In order to dismantle the handle button and decorative plates, primarily the outer part of the mechanism must be removed, which is attached with a special button. Further needed to eliminate laths which hide latching elements.

Note! It is important to know that the buttons that promote attachment of the outer parts of the mechanism may also have a different design.

If the pen is out of order, it can be repaired. How to repair the handle interior door? First of all you need to know the nature of the damage. Based on this information, it selects the correct instruction and performed rehabilitation mechanism. Before you start dismantling the old handle to determine the type and study design features. To eliminate the knob mechanism, experts advise to get acquainted with more detailed instructions.

How to disassemble the handle interior door push type

Lever handles for interior webs are more common option fittings. They are found everywhere and are easy installation and operation. Structure push products includes two basic elements (external and internal) which are fastened to the central rod.

The operating principle of lever handle is based on a simple mechanism. Such hardware has a latch that is located in a recess mating strips in the closed door position. In order to open the door leaf, it is necessary to press the lever on either side of the door. Removing such mechanisms also includes several steps as in the case with analogues circular. How to disassemble the door handle interior door push-type?

To remove a hardware element, it is necessary to adhere to the instructions. Similar work is under force to any person who does not have special knowledge. First of all you need to remove the screws, the function of which is to fix the trim. This will allow access to the axial element. In such fittings it has four sides. On the Internet you can find a lot of materials to answer the question of how to remove the handle from the interior door. Video and photographs allow for fast and competent dismantling of the hardware element.

In the next step should be to remove the remainder of the handle. You can then proceed to the dismantling of laths on the other side of the door leaf. The second fragment must be removed in the same manner as the first. Thus produced dismantling lever handle used in interior doors.

Removing the door handle interior door (round button): detailed instructions

To disassemble a round door handle in the first place to look for the button. It is located on the inner side. In some cases, the button is located below the opening level. It should be noted that access to this element is sometimes required to twist accessories. How to take a round door handle interior door? The main thing that needs to be done at the initial stage - is to gain access to the button. Then press it by any suitable object such as a screwdriver. You can then proceed directly to the lifting mechanism of the door handle.

Note!In some cases it is necessary to make great efforts in order to press the button.

Followed dismantle decorative element. For this problem, any suitable metal element having a small thickness, e.g., a knife or construction line. With this object you need to hook the cover and remove it. It is worth noting that some of the decorative elements have a special groove, which is used for quick removal.

In order to answer the question of how to disassemble the knob interior door, it is recommended to study the video on this topic. After removing the lining allows access to the locking elements. They need to be unscrewed. So for dismantling round handle with a button.

How to install a handle on interior doors: the push model

In the first place before mounting the push handles on interior doors need to determine the size of the internal opening. This will require leaned against the locking mechanism to the end face of the web. It is very important that the decorative strip and the side surface of the door are on the same plane. Further it is necessary to transfer the product to the surface contour with a pencil. That remains is to connect the line to the end through the construction area.

When installing handles on interior doors with their hands should not forget that the performance of the holes by a special drill bit, which is called the chisel. The sample recess is made by means of conventional bits and hammer. In turn, the area in which the front plate will be located, is organized by applying a chisel.

In order to answer the question of how to set the handle in the interior doors, you need to carefully view the video on this topic. It is important to understand that the features of the installation depends on the material the door, as well as the type of handle and tool set.

In the next stage of installation of the pressure products produced zone markings, which will set the square under the door handles and the hole of the locking mechanism. Next, you need to use a drill and make holes for the latching elements. The recesses are organized on both sides of the web.

After making holes need to clear them from the chips and dust. Next, the assembly of the locking device in the fabric. The mechanism is fixed by means of screws and pads. Next to the square set handle for fixing screws which are used.

Thereafter, for an interior door latch is required to mount the decorative ring. For this there are special flange holes.

The final stage of the installation, as in previous cases, involves the installation of mating strips on the door frame. It is worth remembering that it is only set after the opening for the tongue and screws.

Install the handles on interior doors: Features installation of circular devices

Mount Technology round doorknobs (Knob) differs from the process of setting the pressing of products. This is due to the design of such fittings. Mounting the handle can be made both on removed, and on the hinged on the canvas. The second embodiment is more appropriate as a response simplifies the layout strip on the door frame.

Note!Most often, the installation of handles needed in case of failure of the old mechanism. It is worth noting that some of the problem is quite simple to fix on their own. A method for repairing a door handle interior door depends on the nature of damage. If the device is not subject to restoration, carried out its replacement.

The height of the knob is selected depending on the individual preferences of the hosts. Standard distance from the floor to the device is 90-110 cm. And it is also important to remember that the installation of the new mechanism should be performed with maximum caution when painting refers to the carcass type. This is due to the fact that it is quite easy to damage.

How to put a handle on the interior doors? To install this type of door handle, you must first perform the markup correctly. Then you have to organize two holes. The first is drilled at the end (to latch) and the second - on the web (for the rotary knob). Organization of the holes on the canvas under the handle is performed in several stages. The first thing you want to make a through hole. For this purpose, a special attachment - the crown. In turn, for the subsequent mounting latches used drill pen type.

After organizing all the necessary holes, you can install the handle in the interior doors. However, beginning by screws necessary to fix the latch. For mounting of a round you need to disassemble the top and remove the trim ring.

Both parts of the handles have special holes for the screws. These elements are applied to the outer and inner side of the door and fixed to each other. Next you need to install the trim ring, after which the handle must be pressed until it clicks, indicating that the installation is complete.

Thus, the installation of handles on interior fabric is not very difficult undertaking. It requires remember that the installation process is influenced by such factors as the material of the door lock type, a variety of handles. If necessary, you can always use the services of a qualified professional who will install correctly and promptly.