Cages for rabbits own hands. Step-by-step instruction

Rabbit cage simple design

Due to the simplicity of construction, a similar cell can be made with minimal experience with the tablebright instruments. To produce it, you will need wooden slats and bars, plywood, metal mesh, bitumen tiles and plexiglass. Despite the fact that this type of cell is not particularly difficult, it looks beautiful and interesting, which all members of your family will appreciate.

Collecting the cell frame for rabbits

To facilitate the process of feeding animals, the cage is placed on a raised platform, constructing an additional stand.

The height is selected in such a way that adults and children can take care of animals. To have food and hay at hand, as well as not look for additional storage space for food, the frame is equipped with a roomy shelf.

Cells for rabbits drawings

For the support pillars of the cage a wooden beam of at least 60 × 60 mm with a height of 850 mm is required.

Cage for rabbits with their own hands step by step instruction. Photo

When cutting the wood, do not forget to process the edges of the rails. This will avoid splinters and enhance the aesthetics of the cell design for rabbits.

The main frame supports the base frame and the support for the shelf. For this, screws are screwed on four boards in the upper part of the frame and at a distance of 372 mm from the floor. It is important to properly mark up and follow the geometry of the structure, using a carpenter and level. It should be an even, stable design without distortions and angles.

To make a cage with an additional compartment, in the front board of the upper frame make a neat figured cutout. The cut out part is fastened to the old place with the help of a piano loop. A narrow reclining part will provide access to the inside of the cell in the future.

On the inside of the top and bottom frames additional rails are installed as spacers. They eliminate the shakiness of the structure and serve as a support for the flooring, and therefore require a particularly thorough fit.

Cage for rabbits with their own hands step by step instruction. Photo

In the corners of wooden boards or boards used as a shelf and the base of the cage, make a cutout for the support legs. Shields are installed in their places, after which they consider the work at this stage completed.

Assembling the main compartment

The rabbit cage should delight the owner not only with its strength and reliability, but also with an attractive appearance. Collect the cage for rabbits starting from the front, and in detail to understand all the nuances of the work with their hands will help step-by-step instruction.

Cages for rabbits drawings

In the first stage, the box is assembled under the door. For this purpose, a rectangular frame is assembled from the shelves using furniture dowels and screws. A groove is cut to vertically move the door. A sliding partition frame is constructed with a size slightly larger than the height of the box. From the outer surface of the dowels are installed, after which the door is put in place, setting the dowels in the prepared cuts on the side jambs.

From wooden racks mount the offices on either side of the opening. Gather the rear part of the structure, as well as the side walls.

How to make a cage for rabbits. Photo

Eight racks, of which the rafters of the roof will be made, are cut at an acute angle. The trunnion is assembled by fastening the pairwise pointed elements, after which they are finally fixed with screws. After this, the staples are removed, and the rafters are fastened to the base of the roof.

From the plywood sheet, cut out triangular elements that block access from the doorway to the roof. They are fixed with screws to the central rafters in accordance with the attached diagram.

Cage for rabbits with their own hands step by step instruction. Photo

The roof is covered with plywood sheets , making them according to the drawing. The rear ramp is made with a cutout mounted on the piano loop. The reclining part of the roof will facilitate access to the inner space of the cage. To join the central part of the front roof slope with the side elements, small sections are cut out in its corners.

After the assembly of the base of the cage for rabbits with their own hands is completed, the structure is treated with drying oil, dried, and then painted with one or two layers of oil paint. Despite a longer drying period, it will reliably protect the wood from moisture.

How to trim the walls and roof

Cages for rabbits drawings

The inner side of all the walls, as well as the door of the cage for rabbits, are lined with their own hands using a screwdriver, screws and metal mesh with a cell size of not more than 25 × 25 mm.

First, sew the ends of the cage, and then mount the front wall above the doorway.

In order for the structure to be convenient for the to transport the , the swinging handles are screwed on the sides of the frame support frame.

On the front board of the upper support frame, is installed to fix the narrow swinging part.

Espagnolette is also installed on the door of the cage.

Decorating the design can be a figure of a rabbit cut from a plywood. It is dyed, then glued or fixed with screws on the front wall of the roof.

Protect the piano loop , which provides mobility of the swinging roof part, using a universal adhesive tape. Pasted over the metal, it will prevent rust and ensure reliable operation of the part.

Using a stapler and metal staples measuring 8 mm, bituminous shingles are fastened to the roofing of the rabbit house.

Cage for rabbits with their own hands step by step instruction. Photo

Using a special glue for soft roofing, from a long, narrow piece of bitumen canvas equip the roof ridge .

Cut plexiglass to the size of one of the side walls, after which the upper part of it is assembled with a bolt. If necessary, this element will be able to protect animals from draft and rain. Plexiglass is installed on the frame, fixing it in the lower part with furniture dowels, and at the top - fixing the bolt of the bolt in the pre-drilled hole.

Small stairs and an inner house are collected for animals. After impregnating the linseed oil, the parts are stained and placed inside the cage.

After the paint has completely dried, the cage is transferred to a permanent place, prepares the provisions and populates the rabbits in their new home.

Tips for the construction of cells for rabbits

Despite the fact that rabbits do not belong to animals that are particularly demanding of the content, it is better to rely on the opinion of experienced people in the manufacture and placement of cells.

The main criterion for choosing the location for installation of the rabbit is the lack of drafts .In addition, in the summer, it is better for animals to be in the shade, so you have to equip the canopy or place the cells in the shed.

Do not forget that when breeding rabbits have to resettle the young, separate contain pregnant females and males, etc., so you can not manage one cell. It is better to always have a free room at hand, and the cells themselves should have paddock platforms.

Listen to the advice of experienced breeders, and you do not have to correct your own mistakes and miscalculations.

The floor of the rabbitry is best made from a grid or slats stacked at a distance of 1.5 cm from each other. When operating cells outside the premises, they also equip the lower, tilting floor of the floor from the boards.

The roof of the cage installed in the room is made of the same material as the walls. On the street the rabbit is covered with waterproof roofing material. Tin for this is better not to use.

In the street small houses for animals are located on supports in height from 0.5 to 1 m. Best of all, if inside the cage there will also be a small house with a cutout in the form of a "burrow".

The cells divide several compartments into the , providing an animal lap from one part to the other, as well as hinged covers for cleaning individual rooms.

The dimensions of the rabbitry, in which it is planned to keep the males, are sufficient for their free-range. It must be remembered that males who lead a sedentary lifestyle can become barren.

For every 3-4 females do separate a spacious cell.

Rabbits are kept in the same room as the nursing rabbit. At the same time, they keep one cell free, placing the mother with the smallest animals there for their additional feeding.

The best material for rabbitry is wood - boards, slats, plywood, glued panels. They make a power skeleton and a roof. Depending on the climate and site of installation, cell walls are made of mesh, plywood, rails or boards. In the process of work, special attention is paid to the finishing of materials so that animals can not be injured by splinters, sharp parts of the net or protruding edges of nails and screws.

Cell sizes for rabbits

The dimensions of the cells for breeding rabbits vary widely, depending on the size of the animals, the breed, the purpose of the cell( for males, females with children, rabbits, etc.).

For nursing rabbits , cell sizes should be at least 1.70 - 1.85 m in length, 1 m in width and 0.6 - 0.7 from the floor to the lid. Cells are placed at a distance of 0.7 - 0.8 m from the ground on goats or supports. Animals weighing from 5 kg require rabbits with a length of 1.3-1.5 m and a width of up to 0.7 m. At the same time, the height of the rear wall should be 0.4-0.45 m, and the anterior wall - 10-15 cm higher.

Young rabbits are planted in group rabbitries, where they contain from 8 to 20 individuals. Individual cells are evacuated from 3 to 5 pups who have not reached the age of 3 months. Older animals put no more than 2 - 3 animals per cage. At the same time, one individual must have at least 0.5 square meters.m, and the height of the rabbitry should be more than 35 cm. In group cages, one rabbit should account for at least 0.2 square meters.m, which must be taken into account when making rabbit and placing animals.

Cell sizes for rabbits. Photo by

An adult requires a minimum size of 1 × 0.6 m high 0.6 m high, but these dimensions should be increased by 20 - 30%.

The cells are placed in one or two tiers( the so-called shed).Depending on the size of the animals, the width of the shed is no more than 2 m, and the depth - up to 1 m, setting the cells at a height of about half a meter.

For osrol use a double rabbit with a queen pot - a removable stern compartment for animals up to 1 month. On the compartments the cage is divided by a wooden partition with a crouch of 17x20 cm.

The main thing is that animals in captivity feel comfortable, therefore it is recommended to follow all advice on their placement and content.

Cell construction for rabbits

With a two-tier rabbit-type rabbits, care and feeding of rabbits is facilitated. It is enough to rearrange the structure from time to time with a thick grass - and the animals are provided with food and a clean place for walking.

Photo cell for ornamental rabbits

A wooden structure on the roof of which is equipped with a low box with a waterproof bottom, it will be possible to grow seedlings or greens on the rabbit's roof. This solution has not only high practicality, but also looks effectively on the site.

Cage for rabbits. Photo of

"Two-room" pet house with a common feeding area makes it easier to care for animals and allows to increase the space intended for their walking.

A large cage for rabbits. Photo

Cell designs for rabbits, in which animals are allowed access for walking on the ground, are beneficial not only from the position of keeping animals, but also from the economic side. With a sufficiently large cell volume, its production does not require large material costs.

Triangular cage-hut with a paddock for walking is easy to make. On the day a similar design is placed in place with thick grass, and at night the cage is removed to a stationary elevation.

Spacious rabbit, designed for two seats, has a presentable appearance due to the capacious design, flexible roofing and painting in bright colors. Complete the picture of black metal elements of door hinges and gate valves.

A large summer house for breeding rabbits can contain up to ten individuals. The high door of the building allows you to enter inside for feeding, cleaning and inspection of animals.

The cell of increased depth, divided into two rooms, allows to contain several individuals on each half. An enlarged patio gives comfort during the walking and feeding of animals. Contrasting staining and copper fittings of the cell adds to her grace and presentability.

Cage for decorative rabbits. Photo of

Rabbit cages set at height, often performed in the same housing with an enclosure. A common roof allows you to save material during the construction of a cage for rabbits and provides a convenient and spacious maintenance of animals.

Rectangular rabbit with a single-pit roof is very simple to manufacture and provides all the amenities for animals and care for them. A simple cage for rabbits can be made from wooden bars and laths, boards and wooden lining, and the roof is covered with slate or soft roofing.

Zolotukhin cells with their own hands

The cells of the Russian rabbit breeding Zolotukhin have gained immense popularity due to its simplicity, low cost and simplicity of care for the animals.

The advantages of cells of this type are:

• inclined slate or plywood floor with a grid near the rear wall;
• is a three-tier construction of six cells. The shift of cells to the width of the net in the floor makes it easier to clean;
• possibility of equipping the queen cell in a conventional cell;
• a special feeder that does not require opening the door when feeding;
• low cost.

Improvements taken by an experienced breeder-rationalizer, bring rabbits closer to the conditions in which they are in their natural habitat.

Design features

For the production of a cage for zolotukhin rabbits, wooden boards and slats, slate sheets, tin, polycarbonate panels, metal mesh can be used.

The frame of the structure and partitions are made of wood, and the floor and roof are made of flat slate. The mesh is covered with doors and a small part of the floor at the back wall. The wooden elements of the structure are covered in tin, so that the rabbits do not chew them.

Cell size for rabbits:

• cell width - 2000 mm;
• the height of the three-tier structure is 1500 mm;
• depth - from 700 to 800 mm;
• doors - 400 × 400 mm;
• width of the floor grid - 150-200 mm;
• difference in the level of the front and rear parts of the floor - from 50 to 70 mm.

Drawings of Zolotukhin's cells. Photo of

Each of the three levels represents two cells, separated by two board partitions, between which the hay is stored. The floor, the same roof for the lower tier, is made of slate. The back part of the floor for a width of up to 200 mm is made of mesh. The same upper limit extends each upper cell relative to the lower one so that the feces are removed to the floor or ground. The rear wall is made of polycarbonate and installed in an inclined manner.

Precise dimensions for the manufacture of cells are not needed, enough scheme given by the rabbit breeder. This structure is a construction with a queen cell, so for the usual maintenance of rabbits, the wall with the opening needs to be replaced with a solid wooden shield.

Do not make the door of the queen cell out of the net, because the nest requires a blackout and a shelter from the draft. To young animals do not fall out during harvesting or feeding, in the front of the shelter nailed board measuring 10 centimeters wide.

The design with a partitioned compartment allows easy expansion of space for young rabbits. To do this, remove the board partition.

In winter time, Zolotukhin installs mattock-hole in the cage. It is a wooden box with an increased height of the rear wall. This allows you to create the necessary expansion in the depth of the rabbit "hole".The hole of the mother cell is cut in such a way that there is no jam between the box and the cell floor.

Dimensions of the winter queen cell Zolotukhin for rabbits:

• upper and lower part - from 300 × 300 to 400 × 400 mm;
• front wall - 160 mm;
• rear wall - 260 mm;
• the height of the opening is 150 mm.

The feeder is a long tray that takes 2/3 of the length of the cage. Its front wall is enlarged twofold in comparison with the rear wall, and the bottom has a slope inside the cell by an angle of up to 35 °.Fastening of the trough is made on the rod hinge, which allows to install the tray in the door. This eliminates the need to open the cage when feeding and facilitates the removal of feed from the feeder.

Cages for rabbits with their own hands. Video

As you can see, making a cage for rabbits with their own hands is quite easy. It is important to ensure the convenience and safety of pets, as well as provide for ease of feeding and cleaning.