Vinyl wallpaper gluing begins with a personal acquaintance of
If you do not know how to properly glue walls with vinyl wallpaper, now we'll talk about it. First of all, it is necessary to read the instructions inside the roll. There is a brief description. When buying immediately get the right glue for these cases.
When you look at the wallpaper, you will see that the canvas consists of two layers. The bottom layer is made of paper( or non-woven fabric), and the top layer is made of foamed polyvinyl chloride. During operation, the surface is well cleaned and resists any mechanical action. The top layer is made more often with a pattern or embossing. Vinyl wallpapering also differs depending on the type of the lower layer, but more on this later.
Before you can glue vinyl wallpaper, you need to. ..
Before you paste the vinyl wallpaper, in advance purchase the necessary tools : glue roller, knife, tape measure, scissors, pencil, brush or rubber roller for smoothing, as the spatulacategorically not acceptable, it will knock all the embossing on the vinyl surface.
The walls should be carefully prepared by , they must be cleaned of the remnants of the old finishing material, remove the existing paint and whitewash. After that, treat the walls with a fungicidal compound against fungi. As soon as this compound dries, draw a vertical line on the wall, checking its location with a level. Then prepare the glue in accordance with the attached instructions. Remove the covers of the outlets and switches by turning off the electricity. Take care that there are no drafts in the room.
Vinyl wallpaper gluing technology will fit on one page
Now let's see how to properly paste vinyl wallpaper. Cut them with strips of the necessary length, not forgetting to leave an allowance of 10 cm. Watch for the correct alignment of the pattern. Strips should be applied as butt .Spread the wall with glue and place the first cloth exactly along the line. It is better to work together, so it will be faster and better. One person will stand on the ladder, and the second will help to correctly align the strip in accordance with the figure. Then you can start the smoothing of the sheet all over the surface. At the same time, making sure that there are no air bubbles under the material. For this, it is better to start from the center in different directions .Roller carefully roll the seams. If necessary, use a small brush to lubricate the joint line. The whole set of instructions is well fixed when watching the video "how to glue vinyl wallpaper".
The main circumstance that must be taken into account at this stage is not to destroy the elegant scheme, how to properly paste vinyl wallpaper - is the application of glue. Depending on the lower layer, it is applied only to the wall or also to the sheet in advance. If the lower layer is non-woven, then it is not necessary to pre-impregnate them, if they are paper - they need to be smeared with a thin layer.
Try to gently cut the excess length off the plinth. On the lower edge of the skirting the fabric should lie exactly with an allowance of 4 to 6 mm. The upper edge of the strip also needs to be cut at the ceiling level. It is better to remove the skirting before work, but if this is not possible, then lower the cut off edge bend perpendicular to the wall.
Also a delicate moment is ironing. Knowingly in the list of tools the rubber roller, instead of a spatula which is used in most cases of furnish is specified. It's all about the texture of the material, if you look closely at your purchase, one of the questions will be: how to paste vinyl relief wallpaper? Any hard object or strong pressing will ruin the delicate structure of the surface pattern, so do not miss this moment from sight when working.
Vinyl wallpapering - aftertaste
After everything is completed, glue a strip from the bottom, where the plinth lies against the wall. When sticking the wallpaper in the corners, do it carefully. If the corners are uneven, you may need to cut the wallpaper so that you can glue them well. For the heating battery, the wall can also be attempted to be covered with wallpaper or painted with paint in the appropriate color.
In the places where the sockets and switches are located, make oval incisions and put the caps removed earlier in place by screwing them with screws. On the top of the wallpaper, glue the fillets.
In conclusion, it should be noted that when buying you pay attention to the serial number selected by you batch of wallpaper .All of them should have the same color. When you stick the wallpaper, do not stretch it and smooth it with a roller. Well presented sticking vinyl wallpapers on the video, try, experiment, but do not break the main rules, which dictates the technology of pasting vinyl wallpapers.