Kliemery for lining - secret fastening agents

Kleimery for fixing the lining - what is it?

Wood, as a finishing material, is widely used in construction, decoration, etc. Materials from natural wood or imitating it very often need to be connected with each other or with a carrier base, depending on the place and method of application. The most common among wooden and other facing materials was the connection in the groove.

The presence on the edges of the elements of the groove and its corresponding to the size of the spike provides a quality surface. An example is a board lining, other long-length facing synthetic and composite materials made on the same principle( plastic eurodosks, panels).

The use of nails and screws in the fastening is associated with a high probability of damage to the external surface of the board or panel, often already having applied imitating and protective layers. Dents, cracks, chips of the outer edge of the groove lead to difficult to remove defects and spoil the lining, in addition, with the reuse of facing materials, their quality is further deteriorated after dismantling and extraction of fastening nails or screws.

Freedom from all listed inconveniences gives fastening of a board or panels on clip-braces. Manufactured by stamping the Kleimers for fastening the lining have a special hook, into which the lower fragment of the groove is firmly seated. Depending on the thickness of the board and the specified groove element, various numbers of staples with hooks calculated for this thickness are produced. The larger the number, the greater the thickness of the kleimer hooks.

Cladders for lining - the specific application of

Clips themselves can be fastened to the cladding base, frame base, etc. Being, as a matter of fact, ordinary brackets of fastening, кляймеры provide reliable retention of vagonki and invisibility of places of these fastenings. However, their use is advisable when facing with lightweight lining or similar materials, in view of the large overall load.

The advantage of mounting on these brackets is the complete absence of material damage. Fasteners consist in the accurate installation of the clip hook on the element of the groove and fixing it on the frame, the wall surface, etc., using the fasteners included in the delivery. Staples are stamped from galvanized steel 0.55 mm thick. This design provides the possibility of convenient installation of both internal and external facings.

Mounting brackets on a wooden surface or elements of a wooden frame crate is simple: they are nailed with a pair of nails. But you can use other methods. For example, if the frame structure is made of standard profile metal elements, the fasteners are simply made with standard self-tapping screws.

Clayer for lining - instruction for mounting

As already mentioned, for each type of lining you need your own clip. Indeed, a properly selected clay lumber for the lining, instructions for installation and the next master, will be a guarantee of quality and long-term maintenance of the lining. The general rules remain qualitatively made markings for the framework: with a plumb, level and step of the bar( with a vertical surface facing) not more than sixty centimeters horizontally or vertically, depending on the arrangement of the lining.

On the marking lines on the dowels the elements of the frame base are strengthened. Depending on the material of these elements, foam gaskets can be used, etc. It should be taken into account that possible looseness and inaccuracy of the installation of each of the boards of the lining are accumulated and can lead to distortion of the correct geometry.

To eliminate this, every five to ten cladding elements are measured and corrected for vertical or horizontal installation of the board.

The installation of the first board( with its vertical arrangement) is from the angle according to the level. Klyaymery are fixed on the marks in the middle of each bar. The board is installed with a groove in the clips of the staples, at the indicated step of ten square meters of area it will take about two hundred such staples.

In the groove of the installed board, the comb of the next board is inserted, and the kleimers are mounted and secured in its groove on each bar of the structure. Thus, the skin of the entire surface is fixed. With the horizontal arrangement of the boards of the lining, its fastening is made with a stud upwards. This condition is mandatory for execution, especially when facing the outside surfaces: so that moisture, dust and dirt accumulate in the slots of the boards, their rotting is prevented, and natural ventilation improves.

Attaching clips to the back of the groove of the first horizontal plank is complemented by fastening with a self-tapping stud. This is done on the board of the first and last horizontal belt. In general, the simplicity of using the Kleimer allows you to work for people who do not even have prior experience.

instagram viewer