Getting started with
What are the most advantageous rules for you to follow?
The controller can not enter the apartment without your permission. But if you refuse him, he can draw up an act of non-admission, which "will contribute" then to the fact that you will turn off gas, light and water because of this. This act you will have to sign and get rid of in any way, it's better to let it go. A light and gas shut off, in fact, they have no legal right, if:
- How to fix the Energy Supervision - there is a dangerous condition for life support of people and animals.
- Subscriber, that is you, have a documented debt.
- Your meter is not registered, and this threatens unaccountable consumption.
If you became the culprit of the breakdown and the inspector asked him to do this, he must remove the counter from the counter, seal the packaging, but leave it at the subscriber, so that he took them to the examination. And the subscriber in turn assures this process in the corresponding document.
Those meters that are located on the common area of the staircase are under the responsibility of the housing and communal services.
Before you crack the seal, you need to accumulate the debt and pomereno pay. After hacking, unwind, slow down due to those accumulated debt figures.
Here we have already come to talk about how to carefully remove the seal, but it is worthwhile to find out what the seal looks like on the electricity meter and, according to the form, determine the possibility of removing it unnoticeably.
- Plastic seal in the form of a small disc with a diameter of up to 10 mm. This type of seal is fixed on the wire and pressed with pliers, so that it is impossible to move it along the line and get to the counter.
Use these seals for water and electricity meters. Today the rarely used type of fillings. Remove this seal is not difficult, in addition, it's just elementary! It is very easy to do. Look for the seal nodes on the line, they were pressed with a seal before. So that they do not miss the counter, but pay attention to them can be easily untied. If you are doing the opening for the first time, then it is necessary to apply engine oil to the line to slip and try to untie or pull this seal off the line.
Suddenly, there are any problems, then the seal needs to be temperature-controlled, 80 degrees will be enough that the plastic succumbed. In the seal, after the removal, some holes are found, which afterwards will become a checkpoint of the line or wire to restore the old form. That the hole on the seal widened, and then easily took the line back, you must first indulge with a string or wire. In order to restore the seal on the electricity meter, you need a new fishing line or wire, which will be stretched through the fixed holes. The seal is pressed with pliers, but not very much, that you suddenly that you were able to remove it.
- Lead. Another top question is how to carefully remove the seal. The principle of construction of this seal is the same as that of the previous one, but the material from which the lead is made is important. The material when squeezing( sealing) very strongly grasps and of course just move this seal will not work. But very rarely, and units do it. Used in electrical counters. If it did not work out the seal, try cutting the wire or line under the knife with a knife, which was not noticeable at all. The line is trimmed when the seal is on the table. It is clamped in a vice and drilled holes with a drill. Lead is easily bored. The diameter of the hole must be the same as that of the wire. You can also expand it with it. If the cartridge can not pinch such a small drill, you can clamp it with sheets of paper. The drill must be in good working order. A wire, a fishing line, etc. are passed into the hole.for seal sealing. For expansion we use the same principle as in the previous version. It is necessary to tighten the seal with very great force, but also so that in case of reopening it is not necessary to use the drill again.
- The seals with the number on the hologram sticker also refer to the number of those with which they can be absent. The most used kind. They have different quality of material. They are also made of different components, gluing components, etc. Coping with these seals will help conventional three-liter cans, which can organize partial thermal insulation. In the lid, two holes are made, through which after the two rubber hoses extend to 2 meters long. The pot is filled with boiling water, but gradually, so as not to burst. The seal is covered with cellophane, so that part of the polyethylene hangs in the corners of the seal.
One hose is applied to the seal, and in the other, air( hot steam) is blown. The glue layer on the seal begins to soften, which makes it easy to remove it, and then put it back into place.
The foregoing seals are clearly not all that exist, but it is with them you will have to face our time all the time. Good luck to all!
