Qualitatively executed furnish - pledge of successful execution of any design idea.
Speaking about the interior decoration of living spaces - the design can seriously say on the atmosphere created in the room and play a key role in the formation of the decoration.
One of the popular trends in interior design has recently become a rustic style with an abundance of wooden elements.
In such an interior, an important role is played by assembling the imitation of a beam, the execution of which is capable of giving the room a finished look.
Simulation of the bar is used for various purposes. Most often this is a decorative element, but sometimes it can carry an important functional load.
Video:
If you properly perform the simulation of the beam simulation, you can achieve the effect of unobtrusive zoning space, which will give the room an unusual appearance.
In the durability of this design can not be doubted.
An artificial beam is a strong, high-quality material that does not lose its appearance and performance for many years.
If you have already selected this building material as one of the decorative or functional elements of the future interior, you are probably wondering - how to strengthen the imitation of the timber?
Photo:
In this article, you can find answers to all your questions and learn about the nuances that can make themselves felt in the process.
Technology of work
An artificial beam is rather unpretentious material, the installation of which does not require special construction skills from you.
This factor was one of the main reasons for the high popularity of this material.
By itself, mounting the imitation of the beam with your own hands - is somewhat similar to the installation of a lining, but requires less attention.
However, their differences are also available. Immediately after the purchase it is necessary to give the bursa a little acclimatization.
This process usually takes up to a week. It is necessary that in the process of work - the material does not give a strong shrinkage.
Thanks to this, installation work is greatly simplified and the quality of the final coating is improved. After all the preparations are done, you can start the installation itself.
The installation instruction for imitating a bar is itself a few steps, which will be given below.
Their precise execution and maximum accuracy and accuracy in the process of work guarantee the high quality of the final result.
First of all, the insulating material is attached to the brick wall, which is to be hung with imitation of a bar.
Material sheets are lapped in any convenient way for you. In the future they will be completely pressed by the crate.
Video:
For the installation of the battens( the next stage), a standard square bar is usually used. It is customary to use a beam with a cross section of 30 mm.
This thickness is considered the most comfortable, but it is possible to use a bar of a different thickness. The bars of the crate are fixed at a distance of 40-80 cm from each other.
This depends on the length of the wall, as well as on the size of the insulation sheets. Fasten the crate on the wall in any convenient way.( Depends on the material of the wall).
The space between the battens of the battens can be filled with any available insulator( for example - mineral wool or polystyrene).
Wall warming is an important stage in the construction of any room, so it is better to take care of its quality in advance, because in the future it will be extremely difficult to install.
It is recommended to lay a layer of windproof film over the thermal insulation. The film is laid in a lap and fixed in any convenient way.
After completing the previous steps, it makes sense to seek an answer to the question - how to fix the imitation of a bar. In fact, this process has no special subtleties.
The boards of an artificial beam usually begin to stack, from below leveling the first board in level.
In the future, the horizontal will only need to be monitored. The boards are secured with a spike upward, so that the groove of the next board is entered without any problems.
There are a lot of ways of fixing, however the most common and convenient are:
- The fixing with a screw is screwed into a spike( screwed at an angle of approximately 45 degrees and remains completely invisible in the final design);
- Self-tapping screwed into the face of the beam simulation.(it is screwed to the maximum possible depth to preserve the appearance);
- With the help of nails driven into the groove( not very nice, for it is quite reliable);
- With the help of special fasteners - kleimers.
The latter method is the most effective. It is sufficiently reliable and completely preserves the appearance of the final coating.
There is no need to think much about the question of how to fix the imitation of the beam with the Kleimers.
Video:
The fastening is carried out by means of fastening the Kleimers on the inner side of the spike of each subsequent level.
As a result - the effect is achieved that the bars are fixed only by means of grooves without additional elements.
Service prices
If there is no great desire to perform installation work independently, it makes sense to resort to the services of companies engaged in providing similar services.
On average, the price of mounting the imitation bar depends on the availability of material from the customer, as well as on the area to be covered.
The cost of works carried out may be influenced by the company's fame, weather conditions and the completion of work is necessary.
The total price for the work on the installation of the beam simulation, including all the stages( insulation laying, erection of the crate and final processing and painting) is on average 1,250 rubles per sq.m.
The price may seem overestimated, but the work will be done in a short time, while the quality is guaranteed by the company's name.
Solid companies usually provide a fairly long warranty without any problems, which is the key to your peace of mind.
