We take readings from the counters Mercury, Micron, Energomera

Models of the old

model If you have an induction electricity meter installed in your apartment or on the house pillar, the disk is turned on the front panel, the data removal is not difficult. You must write the testimony on the leaf on the same day of each month. Further everything is very simple - from the existing value you need to subtract the number you wrote out last month. As a result, you should get a monthly electricity consumption. However, this procedure does not end with the data being removed.

A very important point that will slightly simplify the removal process - you have to take readings on the meter just before the comma. The last digit, which is highlighted by another color( most often red, as shown in the photo), is not taken into account. If you consider in a clear example how to remove the monthly consumption, then according to the photo you must write 000004 kW / h( without taking into account the last four).

Further All depends on how to pay electricity in relation to your service organization. Either you just pass the testimony to the organization, or you independently calculate the amount of payment and pay it on the receipt. In the latter case, you need to multiply your withdrawn value by the tariff that you use.

Models of the new sample

Modern electronic meters no longer use rotating discs and mechanical dials. In such models of electricity meters, an electronic display is already installed, which, in addition to the total kW / hr reading, can display the operating time, account for the flow at a certain time of day, etc. All these innovations actually allow you to quickly remove the power consumption for a month and at the same time view the rest, no less important indications.

At first glance, it may seem that with such a mini-computer it will be difficult to take the electricity readings for a month, but this is not so. Everything is much easier than you think. So, to take down the data, you have to perform a few simple steps:

1. Press the "Enter" button( you may have to press several times to find the appropriate parameter).
2. If you have a one-rate electricity meter, write out the value of T1, two-tariff - T1 and T2, three-tariff - T1, T2 and T3.
3. Take the values ​​from the same values ​​in the previous month.
4. Withdrawn indications to transfer to the service organization or independently calculate the amount to be paid. Here you need to consider that if you have an electricity meter for two or three tariffs, each value( T1, T2, T3) must be multiplied by its coefficient, which is indicated in the receipt.

By analogy with this video example, you can take data from the device Mercury 200, Micron, Cascade, Energomera, Neva and Lane Electro. We discussed the advantages and disadvantages of two-rate counters in the corresponding article. With the proper use of household appliances, such electric meters are much more profitable than conventional models!

You should know!

1. If the electric meter was counted according to the second circle, that is, if it was reset, the readings of electricity should be taken as follows: add a unit to the existing figure and subtract the value for the previous month. For example, if you have a five-figure scoreboard( not counting the decimal point) on which after zeroing 00033 is displayed( as in the photo below), you need to add "1" to the left. As a result, from the number 100033 it is necessary to take away the old reading for the month, for example, 99916 kW / h. Completing the same example, you should get 117 kW / h( 100033-99916).By analogy, you can take the reading of a four-digit or six-digit electricity meter.
2. If there is no comma on the mechanical display, as in the photo below( model Energomera ts6803v), and you are at a loss with the data removal for a month, there are two ways out of the situation. Better, of course, immediately clarify the organization that installed an electricity meter, how to correctly take monthly electricity readings. But, if you yourself forgot to specify this moment, then visually look at the front panel. The tenth share of electricity consumption should be highlighted in a different color - red, if there is no comma. In the event that there is no visual branch, then you need to remove all 4 or 5 digits and write it in the receipt.
3. The reading of the readings from the three-phase electricity meter does not differ from the single-phase model. It is only necessary to write out all numbers after the comma and subtract from the values ​​of the previous month.
4. If you have a modern electronic meter in the house or apartment, you can send the indications to the service organization automatically - in the remote mode. In this case, you do not need to take the meter data every month. The receipt itself will come to the address. Automated monitoring and reading system, called ASKUE is very convenient, especially if you have a multi-tariff electricity meter.

As you can see, it's not at all difficult to consider the monthly electricity consumption yourself and it does not even matter, a one-rate electricity meter, or a multi-tariff, single-phase or three-phase, electronic or induction. We hope that the material was understandable for you and now you know how to take the meter reading. We recommend that you review the provided video examples, which show instructions on how to take the data yourself!

Also read:

• How to stop the electricity meter with a magnet
• How much does the electric power heat the floor
• How to pay less for light legally