Fence from the euro fence itself. Step-by-step instruction with photo

How much does a fence of euro fence: materials plus the work of

? On average, the running meter will cost from one thousand rubles along with the installation work. If you mount the fence with your own hands, then its installation will be cheaper. The price of the fence depends on several factors:

• type of euro trolley - the manufacturer's brand influences, the quality of manufacture, the thickness of the coating;
• the height of the bar - from 1,5 to 2 m;
• the width of the pins and the distance between them, which affects the number of laths by 1 stitch.m fencing.

Calculate the amount of material for the fence

Make a fence of euro fences easy on your own. Before the purchase of components you will need to calculate their number. You will need:

• euro barrel;
• bearing supporting poles, usually for these purposes is used proftruba cross-section 60 * 60 mm;
• wireframe transverse lugs - proftrub 40 * 20 mm;
• fasteners - self-tapping screws 4 pcs.on one bar( two on the upper lag and 2 on the bottom).

To determine the specific number of strips, it is necessary to know several rules for installing a fence from a fence.

The total length of the fence is measured along the perimeter of the section to be fenced.

It is necessary to subtract the length of the gate and gates from the total figures( their total length is summed up).

Fence from a metal fence with your own hands. Photo step-by-step

The number of pillars is calculated taking into account that the distance between them is equal to 2.5 m, according to the following formula:

Number of poles =( length of perimeter fencing - length of gate and gate) / distance between poles( 2.5 m).

To this indicator, the required number of poles for the installation of gates( wickets) is added.

Calculation of the number of strips is made using the formula:

Number of eurostacks = length of the fence /( width of the bar + width of the gap between the slats).

If a two-sided fence installation is planned, this number is multiplied by 2.

Profile pipe for

fence If is recommended as a supporting element for , rather than making brick poles, it can be of any kind - with a round or squaresection, 60 * 60 or 80 * 80 mm, with a wall thickness of 2 or 4 mm.

Euroshield, in contrast to solid corrugated board, does not create sail from the wind, power and wind loads are less, so the requirements for the pillars are not so stringent. Their concreting into the ground in most cases is not required.

We install support pillars

The installation of a fence with our own hands begins with the installation of poles. The step-by-step instruction of the process is as follows.

Drilling ( digging) wells with a depth of 1.1-1.5 m.

Pole installation .The bottom of the hole is better to strengthen by putting hard stones. The well should be filled with gravel, ground with earth.

Fence from the metal fence with your own hands. Photo by step-by-step

Concreting is required only if the soil is loose sandy( or at the owner's request for strengthening strength).

Install the rain protectors on top - plastic plugs .

Installation of transverse logs, fastening of euro trolley

If the columns are concreted, then the procedure for securing the transverse frame lag only starts for the next day. The transverse lower and upper lags are the frame for the installation of the euro fence. Their installation is possible in any order: first, upper, then lower, or vice versa. The crossbars are welded or fixed with screws. You will need the following set of tools: level, roulette, marking pencil, screwdriver. A step-by-step instruction for the job is as follows.

Mount of the upper transverse log at a distance of 50 cm from the top edge of the support post. The horizontal dimension of the cross member is controlled by means of a level.

How to make a fence from a metal fence with your own hands. Photo by step-by-step

Installation of lower crossbars in level at a distance of 30 cm from the ground.

After the frame is mounted, proceed to fasten the fender bar to it. Each bar is fixed to the lag by 4 self-tapping screws: 2 in the upper and 2 in the lower transverse lag.

Fence from the euro barrel. How to make

Euroshield for fence. Photo

Distance between the fence. Types of pins

The distance between the bars of the euro fence determines the degree of openness of the fence. It can be from 2 to 10 cm. The average figure is 5 cm. With a two-sided arrangement of the euro trolley, a step of 8 cm is made on each side - in this case, with a width of 11.8 mm, a virtually dull fence is obtained.

Fence from the metal fence with your own hands. Photo

According to the type of topcoat, the euro-barrel is available with a polymer layer or powder coating( this is a more robust version, it is not susceptible to scratches).Coloring is one- or two-sided. According to the method of processing the edges, we distinguish the slats with folded edges( rolled) and unloaded ones. The shape of the relief and the top edge can also vary. All the differences and decorative "excesses" affect the price of the material.

The height of the fence from the euro trolley

The standard length of the bars of the euro trolley is 1.5, 1.8 and 2 m. The height of the fence is determined by the owner of the site depending on his needs - if the task is to hide the territory from prying eyes,make a two-sided blind fence. For open garden areas, the height of the barrier is 1.5 and 1.8 m with a large gap between the individual slats.

Advantages of the fence from the Euro fence

Euroshield is a promising material with many advantages:

• wear resistance - fencing will last from 30 years and above without changing the appearance;
• unpretentiousness in care - the fence does not require painting, does not decay, so there is no need to repair or replace the elements;
• easy installation - the fence can be installed independently for 1-2 days;
• neat appearance;
• low cost is one of the most inexpensive and durable materials.

Photo of fences from the euro fence

A clear picture of the products and the sequence of installation gives the fence photo from the fence. Due to the variety of colors of the polymer coating, you can choose a sample for wood, brick, stone, make a fence from the euro fence of the original color, unlike the neighboring fences.

Fence from a metal picket fence. Photo of