Installation of interior doors

Features of the accessories

are so specific products that it is very difficult to say something specific about their species and diversity. However, it is possible to distinguish three general types of such laths: ordinary, telescopic and combined docks. The first option is a simple laminated board covered with veneer. Such products may differ from each other only in the form of a decorative coating. The possible width of such dobors is 100, 110, 150 and 200 mm.

The second option( telescopic dodges) is also called dialing. With their help, it is possible to conduct the lining of the opening in a wall of any thickness. The fact is that the set of strips are made according to the principle of reiki-lining, and this allows you to adjust the necessary thickness of the material. As with simple docks, this type of products differs in color and type of finish. Their width can be 90, 120 and 150 mm.

Combined products combine the functions of the clypeus and door trim. Similar donors are a decorative corner, which is placed on the door frame with special deep grooves in the ends. These gaps are intended for installation of clypees. Such donors will not be able to be installed on a wall too thick. However, for a small increase in the size of the door frame, they are perfect.

There are cases when the door frame is skewed and the upper bar deviates significantly from the horizontal, more than 6% of its length. At the same time, the door leaf was fitted under the skewed box. In such situations, it is not recommended to put the docks without reworking the door. It should be said that the box itself can not be skewed. The reason is often found in the presence of constructive defects, and if they are not corrected, the devices will not be able to correct the situation. Because of this they can deform.

If you need to equip the out-of-town buildings, you can buy doors with boxes that have already been prepared for installation of the gates, namely, they have chosen a slotted quarter, which allows you to combine the box with additional racks. There are also door constructions with a box, in which there are no the above devices. For the first option, both wooden and chip strips with a thickness of 1.5 cm are suitable.

Dimensions of the strips are usually determined only when the base box is installed. They depend on the distance from the edge of the opening to the groove for the dock in the box. Thus, the width of the gates will be equal to the existing gap. Most often it is 9-11 mm, but other options are possible. Additional strips with a groove are nailed to small carnations to an unspecified base. In this case, there should be a distance of about 270 mm between the nails. It is allowed to grease the joints with glue, and then insert the groove in the gap of the doorway. Below, we'll figure out how to put the dashboards on the interior door, but first let's look at the main advantages of these structural elements.

What good are the docks?

• First of all, it is worth noting that the installation of the door unit, expandable with the help of the dice, is very fast.
• In addition, their use excludes wet finishing processes, which have a bad effect on the wood that is nearby.
• It should also be noted that due to additions, the durability of the door structure increases.
• And, of course, it needs to be said that the doors make the appearance of the door more attractive and presentable.

Of what are manufactured the

As a material for additional rails often used edging or sheet piling. If the width of the adjacent wall is large, it is recommended to give preference to waterproof plywood BS.It is still suitable in the event that the equipment is installed in a room with a high level of humidity. All materials from which the dough are made are pasted with a decorative self-adhesive film.

It is worth mentioning that today it is more profitable to use ready-made additional boards made of MDF with a special decorative coating, and not to do the cuts themselves. Factory products have standard sizes, which vary from 80 to 500 mm. If the walls in the room are too thick, then you need a set of docks. Especially for such cases, additional MDF boards with a tongue-and-groove lock are manufactured.

As a rule, the dies are placed in a special recess located on the inside of the box. Sometimes additional strips are required to be placed on a previously installed door. Then usually use docking equipment. Such products are most likely to be installed in rooms with a normal level of humidity and moderate temperature. They are also mounted on very high quality door leaves. Sometimes they use docks, which are shoved under the box. They are also called underlays.

How to install the interior doors

Selection of materials and tools

To install interior cabinets, tools are indispensable. One way or another, you will need: a hand-held circular saw, a wood milling cutter, and a soft-clad clamp. The latter is mainly needed in order to be able to press the saw with the help of a saw to the stool upwards. As a result, you get a design that functions like a circular saw. You can improve the quality of the instrument. This is done simply: at a distance of 400-500 mm from the working gas burner, a pipe with heat-shrinkable properties is heated, after which it is placed on the clamp in 3-4 layers.

To install the interior doors, you will need 3 or 4 strong stools. They should have the same height and not stagger. Still need to be 5-6 wooden bars about 30 × 30 and 40 × 40 mm in size, as well as 10 wedges and several pieces of strip from the sheet of packing plywood( you can use gypsum board).

How to install the door closer to the interior door

All the above types of dobors have their own peculiarities in the installation. It is about these features of the installation that will be described below.

Step-by-step process of installing conventional tools:

1. Immediately it is necessary to say that the doses are put already after the installation of the door block is finished, and the foam has time to freeze. If there are special hollows in the box, you need to clean them thoroughly. If such a recess is not provided, then it is necessary to remove the space from the mounting foam, which is located behind the box.
2. After finishing the preparatory phase, you can proceed directly to the installation process. Initially, the upper fitting is fitted to fit. To do this, the bar should first be trimmed along the length, then along the width.
3. For proper adjustment to the width, the fitting must be installed in its place so that it looks outwards to the underside. After that, two labels are placed. Then the additional bar can be pulled out. Then the resulting labels are connected with each other by a line. The bar is cut with a jigsaw.
4. Next, you need to fit two side gates in the manner described above. By the same scheme, the length and width of the slats are determined.
5. There should be no slots between the top and side rails, this is important. Thus, the upper bar must be located on the side rails strictly horizontally. This can be controlled by using a level.
6. Only when you have checked the horizontality of the installed slats, you can begin to fasten them. To do this, first of all, you must prevent the appearance of possible slots. To do this, using a wooden wedge, the bar must be pushed between the existing door frame and the opening. If there are no wooden wedges, other materials may be used( carton or frozen foam may still be suitable).If cardboard is used, it will need to be folded into several layers.
7. After wedging, it is necessary to check the upper and lateral docking areas. First of all, evaluate how accurately the additional bar is installed. In addition, it should be checked whether the lower parts of the side gates are correctly assembled. If necessary, they will be straightened or wedged by means of inserts from racks or a bar.
8. Then the docks should be fixed from one edge to the other. Now you need to take the mounting foam and fill it with the space between the drill and the opening. When the mixture cools, you can fill the remaining space. Then you can install the casing in place.

The installation of telescopic planks has much in common with the installation of conventional tools. The difference is only in the way of connecting individual racks with each other. They will be "stacked" on top of each other. So, in no case can not completely collect a large shield and put it in assembled form. You need to do this gradually. Begin with the fact that the perimeter of the doorway sets the first bar and only after it is securely fixed, the second row is assembled.

If you install the whole board, then the connection of the dial plates will fail. Therefore, in this form it is usually not put. In particular, this applies to sets of three or more bars. In some cases it is possible to do with telescopic racks, which are put simultaneously. But this requires experience and a sufficient number of struts.

Now let's look at the combined method of installing the dashboards and clypees on the interior doors. It is very simple, if only because there is no need for additional fixing of the gates during its execution. Usually it is enough simply to insert the slats in the grooves in the box, and also to adjust the corners. Initially, as a rule, pruned and installed the top doppel, and after that, side strips are fitted to it. And lateral docks should be cut only from the bottom side. If you do this at the top, you can damage the special notch. It is thanks to this notch that all the additional racks can be connected correctly.

Doors for interior doors: photo

How to fix the interior doors: video