Booth for the dog with their own hands. Drawings and dimensions. Best Masterclasses

Booth sizes for a dog

Booth sizes for a dog can be adjusted depending on the real size of the dog. So, his chest should be free to pass into the building's laz. Therefore, to its width it is necessary to add from 5 to 8 cm. At the same time, the best height of the eye is equal to the value that is less by 5 cm of the growth of the dog at the withers. At the same time, the maximum vertical size of the booth and its depth should be 5-8 cm more than the height of the animal at the withers.

dimensions of the booth for the dog. Photo

The dimensions of the booth can vary, but only in a larger direction. Especially such a rule is important to observe when the design is created for the puppy. When constructing a dog booth with your own hands, you should always remember the following points:

• Dog in his home should not interfere so that he can freely lie down or become.
• The inlet must be comfortable. For this, it can even be slightly increased in size.
• The structure for a dog needs to insulate the so that the dog is warm in winter.
• Roof and wall construction must reliably protect the animal from various precipitation and wind.
• Budku must be built of environmentally friendly material. It is best if it is made of wood, since wood is harmless to the health of the dog.
• The structure should be placed on the territory of the infield with a windless side. In this case, the dog must have the maximum overview.
• A good design of the booth is a structure with a small loft in the roof where you can store different things, including toys and dog dishes.
• The laz is recommended to perform on a short wall. Thanks to this arrangement, it will be more convenient for a dog to climb into his home.
• Before creating a facility for a dog, it is necessary to carefully compile the calculation of the booth size. It is best to double-check the dimensions. This will build an ideal design for the animal.

booth for the dog with their own hands - drawing

booth for the dog own hands. Video instruction

Booth with gable roof. Master class

It is recommended to create roofs with two slopes on small sized booths, because such structures increase the weight of structures that are inconvenient to raise during harvesting.

Drawing booth for the dog

Step 1. Creating the frame

The bottom frame is made of four bars, each side of which is 50 mm. In its corners, the posts are fixed in an upright position. Their size should correspond to the height of the booth. In the upper part they are tied with the same bars. Strength of the frame of the booth for the dog is enhanced by securing additional jumpers on the bottom and on both sides of the hole.

how to make a booth for a dog. Step-by-step photos of

Step 2. Fastening the roof

Two designs are made, for each of which two blocks of 50x50 mm size are used. They connect with each other so that an angle of 40 degrees is obtained between them. Blanks are installed vertically on the frame level with smaller walls and fixed temporarily with the help of nails. Two installed workpieces at the top points are joined together horizontally by a bar with the same cross section. At the same time, it is necessary to provide that it protrudes 200 mm in front of the kennel. Further, two bars of the same length are fixed in the lower points of the rafters.

Step 3. Sheathing of the kennel

A wooden box for the dog is sheathed on the outside by a lining. During operation, care must be taken that there are no gaps between the boards. At the bottom cover the roofing material and, if necessary, fix the supports, made of uneven bars.

Step 4. Thermal insulation

First the frame of the booth for the dog on the inside is lined with pergam. It is fixed in the corners with a stapler. Then foam or mineral wool is fixed. Then the insulation is covered with pergamon, on top of which plywood is fixed. It is also laid on the floor.

Step 5. Roof cover

Temporarily fixed roof frame is removed, and its interior is covered with plywood. Then the structure turns to its natural position. Next, the plywood is fixed on the plywood, on which the heater is laid. Then the heat-insulating material is covered again with a peppermint. At the end fixed corrugated board. Self-tapping is used to fix it.

Sheepdog Booth with her own hands. Step-by-step photos of

If you make a booth with your own hands with an opening roof, in which the slope is only one way, then this design will facilitate the cleaning and disinfection of the house for the dog. It will also allow the dog to settle on top of its home, as many dogs like to lie in such places.

It is important to perform warming when creating a kennel. This will protect the dog from the cold. This is also facilitated by the location of the climbing wall in a larger wall, but at the same time it must be moved to one side. If such a rule is met during the construction of the house for the dog, then the animal will have a remarkable warm place. In doing so, it will be protected from the wind.

Step 1. Creating a frame for the bottom

In accordance with the drawing booths for the dog are taken bars, each side of which is 40 mm. They are cut to the size of the bottom. Then they form a rectangle on a flat surface. Its angles are fixed with the help of self-tapping screws. If the dog is large, the frame needs to be strengthened. For this purpose additional jumpers are fixed in it. Then it, on the one hand, is lined with planks.

booth for the shepherd yourself. Step-by-Step Steps

Step 2. Warming of the bottom

The frame, trimmed, on the one hand, with boards, turns over the bars. Its interior is covered with pergamon, which is fixed with the help of staples. Then the foam is laid between the beams. This material is cut in accordance with the dimensions of the frame, and its thickness should be equal to the height of the beams. Then the insulation is covered with a layer of pergamina and a finishing floor is created.

Step 3. Making the frame

According to the drawing of the booth for the dog, the beam with the size of each side of 100 mm is cut into 4 parts. Two of them should have a length equal to the height of the structure, and the other 2 parts of the frame must be 70-100 mm longer. All the cut bars are mounted at the corners of the bottom vertically. Racks with a longer length are fixed to the front with nails or screws, and others - in the back of the kennel. Thanks to this arrangement, the roof will be inclined. Also, when creating the frame, additional bars are used, which are fixed to the center of the walls in an upright position. On the sides of the hole, too, two bars are installed, but they are small in size. To ensure that the frame has increased strength, it is necessary to use metal plates, with which the internal joints are strengthened.

Step 4. Mounting of the skin on the walls

For the external cladding of the structure, a lining is used. Then warm the frame of the dog booth from the inside. First, the paper is fixed using staple staples. Then foam or mineral wool is laid between the bars. Further, the heat-insulating material is covered with pergamon, which is covered with plywood. Also for this you can use chipboard or any other similar material. To fix the skin, it is necessary to use nails of small size with a zinc coating. At the same time, their hats should always be drowned in a tree so that the dog can not get hurt.

Shepherd's Sheepdog. Photo master-class

Step 5. Creating a roof

A single-pitched roof is made using bars with a side dimension of 40 mm each, and an OSD sheet. First, a frame is created. Its dimensions correspond to the inner length and width of the booth. Then a detail of the same size is cut from the OSB sheet, which is fixed on the manufactured structure. Then the heater is laid in the frame. It must be covered with a film. To fix it, you use the same stapler. At the next stage, another piece of plywood is cut out, the dimensions of which must be three sides 100 mm longer than the hull frame for the dog, and one( front) - 150-200 mm. This will protect the walls of the structure and laz from various precipitations.

If you do not have a sheet of OSB or plywood at hand, then you can use boards that are about 25 mm thick. The created design, upholstered with soft tile or roofing felt, is fixed on the kennel with the help of loops.

Step 6. Finishing the

A ready-made dog box on the outside is treated with the antiseptic .Also impregnation is suitable for this. The applied funds must be completely dry. Then, at the bottom of the structure, a ruberoid is fixed. In this case, the insulating material must go 50 mm to the walls of the kennel. Further, on the roofing material there are fixed two bars, the size of which is 100x50 mm. They must also be treated with an antiseptic or impregnation agent. Then the house is turned over and its laz is made using wooden platbands.

Step 7. Installation of the Shepherd's Shelter

After the production of the booth is completed, a place for the construction is selected. It must be necessarily closed from the wind, smooth, dry and close to the house. It is best if the place is well lit, and located near any shelter or tree. The last feature of the installation of the booth will allow the dog, if necessary, to hide from the sun's rays.

Ready-made booth for a sheep-dog with their own hands. Photo

Booth with a tambour with your own hands

To make the dog booth more comfortable you can build it with a tambour. Such a dwelling for a dog will consist of two compartments:

• the distal part being a sleeping place;
• the near part, allowing to increase protection against cold and draft.

The compartments are divided among themselves by means of a heat-insulated partition, in which the laz is placed.

It is not so difficult to make a booth for a dog, but it is not recommended to make a big bed when it is being built, as almost all dogs curl up during sleep. At the same time, it is necessary to provide for an opportunity for the animal to stretch freely in the vestibule, when it will rest at this place. Therefore, the dimensions of this part of the house should correspond to the growth of the dog.

Booth for a dog with a tambour. Dimensions and drawing

The assembly of the structure with the tambour occurs in the same way as the other booths. A distinctive feature of this house is the partition between two sections of the dwelling. It is created from bars with a section of 40x40 mm, plywood, insulation material and self-tapping screws. First, a frame is made, the dimensions of which correspond to the width and height of the booth's room. Then to it, on the one hand, plywood is nailed. Then in it the heater is laid, on top of which one more sheet of plywood is fixed.

In order for the partition to be easily removed, it is necessary to take two slats from a tree and select longitudinal slots in them using a milling cutter. Their width should be equal to the thickness of the partition. After this, the slats are fixed on the walls of the booth. After that, it remains to insert the partition into the created grooves.

Kennel from the bar( for Alabai) with your own hands

After the calculation of the size of the booth, the following drawing was obtained, which shows the approximate dimensions of the dwelling for a large dog, for example, Alabai. In addition to the laser, the window can be provided in the design for review. It must be located in the side wall.

Alabaya bunker - drawing with dimensions

Before construction starts, the kennel from the timber is best done by constructing the platform of the from logs. They need to be sheared and put together in a single structure, which will then need to be painted. After this, the erection of the kennel itself begins. The construction process will be carried out quickly, if you prepare the bars in advance. They need to be cut to size and planed from all sides.

According to the developed drawing the first crown of dwelling for a dog is put whole. Further, the side walls are also made of whole bars. Where there is a laz and a window, pieces of material are used.

After the erection of the load-bearing structure of the booth, the roof is constructed. It is best to make it a "house", so that it does not accumulate a lot of snow, since a large area of ​​a single-deck structure will contribute to this. In a dwelling for a large dog you need to provide a ceiling. He will make the kennel warmer. After its creation, the roof panels are assembled. At the same time the rafter system is not manufactured, if the design performs a decorative role. On the shields, the roofing material is laid. It can be soft or metal tiles. It is best to use the material that was used in the construction of a dwelling house or a bath. After this, the shields are joined together by means of nails or screws and the pediments of the structure are mistaken.

At the final stage, the made roof is fixed on the walls of the kennel. At the same time, we do not need to insulate the frame of the booth for the dog, since it is made of a bar. This material itself is warm and characterized by low thermal conductivity.

Care for the dog kennel

Now, when it became known how to make a booth with their own hands, it remains to learn how to take care of it. First of all, you need to remember that cleaning the dog's dwelling should be done regularly. Usually it is carried out once a month. Thus disinfection of a design is spent in the summer every month, and in a winter and spring period - once a season.

During the cleaning of the kennel, bones and other scrapings are removed, is treated with lysol , which allows to get rid of parasites. Also, for these purposes, three percent of creolin or formalin can be used. Do not allow the dog to enter the booth until the solution dries!