His hands can do a variety of swing and make a reality of their own ideas
Useful advice!To prevent premature deterioration of wood, enough to establish the structure under a canopy or awning to pull on it. Because of this you will ensure the protection of the swing from the harmful effects of the sun and rain. Special protective equipment and antiseptic compositions solve the problem with parasites, fungi, rot and moisture processes.
Benefits of creating wooden garden swing with your hands
Wood has excellent technical and operational characteristics. Due to the properties of the material, it is possible to create a truly comfortable and nice structure.
Adults also do not mind to relax and unwind, stately swaying on a swing
Note!Costs for the purchase of material not high. In addition to this, creating the product yourself, you save on the masters services.
Garden swings from a tree with his own hands: photos and drawings, dimensions and modifications
If you have decided to focus on creating a swing at their summer cottage on their own in the first place is worth determine the type of design you wish to install, and determine an appropriate location for its placement. To facilitate and accelerate the design and preparation, use a photo of the swing to give his own hands made of wood, which a lot of drawings on the Internet.
Transportable swing can be moved to any location area, depending on weather conditions
The choice of location for the children swing with their hands from a tree
Any type of construction, which is carried out on the territory of the country the land begins with the design and selection of an appropriate site.
Note!The principle that is used to select the place for the construction, applies not only to children's swing from a tree. These requirements apply to the other embodiment.
Simple children's swings made with wooden planks and rope
As much as possible should be selected on the gardening area of land with a smooth surface. It is desirable that this area was sheltered from the sun and rain. An ideal place to create a swing - a site under a tree, where a dense shadow falls. Capable of performing the installation on the porch, the dark canopy.
All of these conditions have a direct impact on the level of comfort of operation, as to sit on the seat of the swing, the red-hot in the sun, it is unpleasant and uncomfortable. A smooth the impact of rain can damage the structure.
By placing in a garden swing for children, it is necessary to provide enough space for rocking
It should also take into account the fact that as the movement of the sun across the sky, the shadow cast by a tree or other object to be moved. For the installation should be chosen such a place, where the shadow will stand at midday. In this segment of the day the sun provides the most powerful and aggressive influence.
Drawings and photos Garden swings with his hands out of wood for the garden
If we talk about universal design, the swing suspended type installed on the support of A-shaped object will become a real holiday for the whole family. Moreover, they can be installed both on the large suburban areas and in small gardens near the house. And the process is costly in terms of time and effort resources.
Simple wooden swing for children's outdoor games
Note!Of course, buy ready-made structure in the store is much easier and faster. But in this case it is unlikely to meet all your requirements in terms of design, dimensions and so on. Creation of own drawings swing garden with his own hands made of wood construction allow delegating all the necessary features.
Swings in a quiet corner of the garden will allow to enjoy the flavors of green
Construction of a wooden swing to give his own hands: drawings and selection of materials
At the initial stage, the preparation of materials to create a garden swing with your hands, a photo that you like the most. can be easily understood on the basis of the drawings, a number of pieces required for assembly design and what size they should have.
Dimensional table for creating blanks:
Detail design | Dimensions transverse part preform cm | End length, cm | The required number of pieces, pieces. |
The frame part of the structure | |||
Spacer (top) | 4,5h14 | 23 | 2 |
Spacer (lower) | 4,5h14 | 96 | 2 |
Leg | 4,5h9 | 198,7 | 4 |
girth rail | 4,5h14 | 210 | 1 |
Seat Details | |||
rear rack | 3,5h7 | 60 | 2 |
Bar (reference) | 3,5h7 | 95,5 | 2 |
Bar (seat) | 3,5h7 | 120 | 2 |
Armrest | 3,5h7 | 60 | 2 |
back Planck | 2,5h7 | 130 | 2 |
Support for the armrest | 3,5h7 | 27,5 | 2 |
Plank seat | 2,5h7 | 128,4 | 8 |
Upper limit | 2,5h9 | 130 | 1 |
In addition, for connecting the aforementioned preforms into a unitary structure, you need to have fasteners with different parameters.
Related article:
Drawings and photos Garden swings his metal hands: the dimensions and creating instruction. Recommendations for installation design with a visor of polycarbonate. Classification of metal products.
Additional materials for the creation of family or children hanging wooden swing
The final design size of 2.1 m (width) 1,235 m (depth) and 1.9 m (height). Recommended for use as raw materials impregnated pine.
Dimensional table fasteners:
Type fastening element | The dimensions, mm |
Screws coated with zinc | 8h65 |
Screws (24 pcs.) | 8h50 |
screws | 8h38 |
Screws (8 pcs.) | 10h75 |
Nails (roofing) | 2,5h40 |
Nails (convex cap) | 2,5h65 |
Screws with a square-shaped head and washers under them (8 pcs.) | 8h100 |
Pan head bolts and nuts for them (2 pcs.) | 10h125 |
Eye bolts with washers under them and the lock nuts (6 pcs.) | 100 |
Useful advice!Prepare suitable for pre-treatment of wood antiseptic, as well as materials to perform finishing. These moments are conceived during the design and planning of future construction.
In addition to the fasteners you'll need some additional materials: a pair of wooden struts to the corner region (length 38 cm), sand paper with 120 grit level, hooks, equipped with a fuse (6 pcs., 5 mm), the chain length of 4.4 m (thickness 2 cm units).
Swing with a soft mattress and cozy cushions - the perfect place to relax
Drawings Garden swings: how to make their own hands the family structure
To accommodate the swing is recommended to choose the back of the house. Even if your site is fenced from the noisy streets and neighbors, this area will still be very comfortable and quiet. Backyard in most cases, settling down to rest, and you can feel free to use it for the installation of family or children's outdoor wooden swing for the garden.
Wooden swing-bench, step 1: sketch design and preparation of parts for assembly
Marking the reference portion of the article
For the manufacture of a support crossbeam need to saw to the specified size with a circular saw. At a distance of 15 cm from each end mark are performed and performed a flat line. It must pass on all the faces on the beam. This line will be considered as an exterior face for supporting the A-shaped.
On the front part of the leg should be applied to the layout for oblique cuts. For this square is held together by a truss pins. Installation of one of the pins is carried out on a larger cathetus (at a distance of 316 mm from the corner), and the other - to the smaller (at a distance of 97 mm from the corner). The foot is placed on the line and is marked position gon. You should get to perform bevel cutting lower.
Wooden bench swing-step 2: application of the adhesive and the bond between the components
After that, the layout position gon line on the edge of the legs. To do this, move the elbow in the direction along the legs, to combine it with the previous line position. Outlining the length of the line, you can move the angle further.
Note!This procedure is performed as long as the square will not be billed for more than 6 times.
Wooden bench-swing, Step 3: fixing parts connected by screws
Last line of markup is designed to cross-cut the beam. These positions are marked by straight lines leading to each of the faces of the legs. To make the mold, it is necessary to saw off material on the other side, which is not processed.
Cutting support portion structure
To cut off a material with a hacksaw, it should first put on edge and clamped in Sawhorses. Cutting is carried out strictly according to the markup. Do not forget to monitor the side. This is particularly true of the upper cutting zone. Sometimes it is necessary to align the bevel. It's enough to handle a plane end of the cut.
Wooden swing-bench, step 4: the backrest assembly and the seat structure
To form a second leg to put her first, joint to joint. After that, all the marks on the bevel and length are transferred to the second leg and saw off on the markup.
Then both feet are placed on the edge so that the end parts of vertices located on opposite sides of the transverse beam. The lower part of the legs is moved to the side as long until a distance of 1.2 m. The upper part of these components have to fit the bolt. To check the bevel, use the line, putting it to the ends. Perform adjustments, if that is necessary.
Wooden swing-bench, Step 5: Mount the armrests
From Foot base distance is measured 50 cm and the lower bar is applied. Further tolerated leg line, as well as upper and lower parts of the bar on the relevant details. The upper bar is placed on the feet. It must be done so that it is positioned at 15 cm lower than the transverse beam passes, and was parallel to the first bar. The marking is carried out in exactly the same manner as in the previous embodiment.
Thereafter the bars are cleaned, and the marking is aligned on the surface. On the set points of these elements must be sawn to the desired length.
Wooden swing-bench, step 6: The suspension design
Drawings garden swing with your hands: the assembly supporting part
The next stage of construction - fit check. You transfer marking using gon on the inside of the legs.
Useful advice!You can use these 4 items as samples for the manufacture of the second side of the frame. She's going the same way.
The template is set at around 22 mm and is produced between the counting lines perpendicularly arranged on the inner side of each of the legs.
A-shaped design - the most reliable as a support for the swing
forming through holes in the foot diameter of 4.5 mm at 30 mm from the bottom of the joists. Fixation parts screws (65 mm). Similar operations are performed in the upper leg. Only in this case, the other screws (38 mm) are used for fastening.
Next you need to connect the upper bar and bolt. The spacer is fixed through-screw, whose size is 65 mm. The upper part of the element is fixed to the bottom face of the beam at the end portion a screw 38 mm in a pre-formed hole (4.5 mm).
Swing set on the terrace - the perfect place for hanging out with family and friends
Creating a garden seat for swings with his hands in wood
Seat creation technology implemented in phases based on the L-shaped frame made of boards (40-50 mm).
Note!Drawings of children's swings with his hands out of wood are very similar to conventional family-type structures. Only in this case, you can shorten the seat, making a single swing, or add a few seatbelt for fixing each child on a large seat.
Swings of the pallet, step 3: the fixation of the swing using strong ropes or rope
Photo of a wooden swing to give your hands and hanging process
In order to hang the seat in the lateral part (approximately in the middle) should be set screws, complete with rings. Two rings are fixed at the bottom of the crossbar. These elements are used to join and support the swing via hangers. In this case the circuit used.
Connecting elements between the main items are carbines. suspension length is optional. The optimum height for placing the bench is 30 cm above the ground.
Drawing double swing suspended from a metal chain
Useful advice!Chain can be replaced by a rope or a strong rope. The expediency of this substitution is that the rope or rope generates much less noise than the circuit. But it is worth remembering that the lifetimes they have also reduced as compared with metal. over time the rope is stretched under the influence of weight loads, so from time to time will have to perform altitude correction swing.
Swing, suspended from a tree with a rope
The final stage of construction of building
The next stage of construction will be completed. In order to protect the finished structure, swing be treated lacquered composition. It will provide a smooth surface to preserve the natural beauty of the wood and prolong the operating life of the product.
Depending on personal preferences, the swing can be painted in any of the favorite flowers or perform installation of a small shed. Be a little imagination at this stage, and you will be able to create a unique product.
Ready designs can be decorated with cushions, rugs and other decorative elements
can be put to greater comfort in the bench pillow or a small mattress, which allows to reduce the rigidity of the planting. Its size must match the size of the seat. Anyone who is familiar with the implementation of technology for upholstery furniture, it may be advisable to use these skills to create the swing. Make soft not only the seat but also the back and armrests, if they are present in your design. Do not forget that the implementation of upholstery is only possible if the product is located under the roof or canopy.
Wooden and metal parts must be periodically swing handle protective compounds
Photo Children's swing from a tree with their hands and how to create them
Children design options much easier to perform, since the requirements for weight loads to them is significantly lower. On the other hand, the rules on safety in this case should be carried out strictly, as children are extremely mobile and can be excited in various ways.
Children's swing of a skateboard made with their own hands
Creating kindergartens swings own hands: video and a variety of manufacturing methods
The most popular designs for the garden are considered swing suspended type. There are several simple methods for creating products for children.
According to the first technique uses the seat of the timber in the form of a wide and thick planks. It carried out the holes (the pair on each side), which is threaded a rope. This is done so that the suspension has been stretched in one hole and out the other, which is located nearby.
Children's swing from a skateboard, step 1: preparation of materials and tools
Useful advice!In order to strengthen the structure to prevent breakage of the board in the area of holes placement under the seat can be installed on either side of a plate with through additional notches. These holes should be placed just below those made in the seat. The rope will pass through the paired holes.
Children's swing from a skateboard, step 2: the dismantling of the rollers from the board and drilling holes in it
The second technique involves the creation of the swing based on the frame-frame of wood. This element is tied to the crossbar, or branch of a tree with ropes, and the free space is filled with small but sturdy planks.
Children's swing from a skateboard, step 3: preparation of wooden bars of circular cross section for armrests
As for the seat structure produced by the third method uses half logs. It should be cut lengthwise. This seat variant is considered to be very durable, but it requires careful handling. timber surface must be well sanded and polished to get rid of knots and burrs.
Children's swing from a skateboard, Step 4: Pulling the rope through the holes boards and bars, armrests
The fourth option to create a design involves the use of the board as the seat and through the metal fasteners. The range of modern shops offering various forms of locking fasteners, so you will have a fairly wide range.
Children's swing from a skateboard, Step 5: Fasten the created design on the tree using carabiners
In terms of design teeter do not impose serious limitations. To create them, you can use any improvised material. For example, the rope can be replaced by a chain, a wooden board used as a seat, the chair can be replaced after removing his foot. Be sure to use bright colors, because the abundance of colors is very popular with the children.