Kitchen furniture with his own hands: how to make it yourself from a tree?

Manufacture of furniture with his own hands - a very useful skill. And even if there is no need to do a whole set from scratch, just update the old kitchen with a few homemade items, too, it will not be difficult. Kitchen furniture with his own hands made from available materials - chipboard, MDF. Much less common tree, although it can be used for decoration. And as the basic idea is better to take a photo from any directory.

The first step: the design

Most often, homemade furniture need for custom kitchens, where conventional kits simply impossible to install or combined with household appliances. To new headsets clearly fit into the interior, in the first place to make the room froze and sketch a plan of arrangement of cabinets. This is followed by drawings of kitchen furniture - separately for each item.

It is important to take into account the functional load of all zones, as well as the growth of the hosts to use the new kitchen was convenient.

design online program suitable to simplify the task. Most of them allow you to make a sketch of the furniture in 3D-format - the printed image will replace the photo of the future headset and facilitate further selection of decor.

The calculation of the amount of materials needed, budgeting and procurement can begin as soon as all the dimensions and facade decoration ideas will be transferred to the paper. If available there is the old kitchen set made of wood or particle board intact, it also can be taken to rework. This will update the kitchen at lower costs and make the job much faster.

Using a template

For furniture, you can use professional templates. But specifically to buy it for rework a set of furniture is not worth it - a simple tool is easy to do and most. To do this, two school rulers of wood stacked at right angles and glued together - it turns flat letter "T" with a scale. After that, the "leg" drilled holes with a diameter of 2 mm at such elevations:

• 8 mm - for basting evroshurupy holes at the ends of articles;
• 16 - thickness of panels of wood or substitutes;
• 32 - thickness of the countertop particleboard;
• 50, 70, 100 and 120 mm - for a fastening indentation marking fittings and decoration.

preparation facades

When buying particle board for facades is better to reserve their cutting in size to the nearest furniture shop. There, all the elements are made with precision and after cutting out the ends of Laminate film - to protect the chipboard from swelling.

Just to refresh outdated kitchen, you can buy ready-made door made of wood or Postforming has with the decor and under their settings to adjust the size of the box.

It is important to bear in mind that the width of the swing elements should be 3-4 mm less than the frame of the cabinet. Then the door would not touch the adjacent module and damage the decor.

You can make the facades and myself, but this delicate work requires skill and special tools. The edges have to buy separately, taking into account the color of the front surface of the particle board. Glued edge tape on the pre-polished ends using ordinary iron. By the way, it is better to buy them from the reserve to a few years cabinets can be updated.

drawers

Actually, the production of own boxes of wood or chipboard does not cause problems, as well as their décor. It is much more difficult to accurately set the rollers and guides. Error 1 mm - and the alteration will no longer look so beautiful as the photo in the magazine, and do not last long boxes.

To do it right will have to remember the math and work with drawings bollards, which were drafted at the design stage of the future of kitchen furniture. The initial data required frame height and the number of boxes on the project. The main task - to determine the axial line roller guides:

• From the height pedestals subtract the lower base (70 mm) and an overall height of 3 mm gap being left between the outer panels of the boxes.
• Divide the resulting number by the number of pull-outs - the result is the height of each facade.
• To determine the width of the runners and divide it by 2. For the running rails 36 mm wide central axis will be at a distance of 18 mm from the edge.
• Added to the obtained figure of a clearance of 2 mm, which prevents contact of the bottom with the heads of screws - it will mounting height above the horizontal guide surfaces.
• On the side walls make an appropriate boxes mark (in this example - 20 mm). From it with a spirit level draw a horizontal line, and which will need to be combined with the center line of the runners.

For the rest of the guide boxes are mounted at the same height in relation to the horizontal rigid jumpers or shelves to ensure full interchangeability of sliding elements.

installation of canopies

Tools that will be required to update the kitchen furniture with new facades:

• end mill;
• drill;
• screwdriver;
• T-shaped pattern.

The number of attachment points will depend on the weight and dimensions of the door. Typically, each of which is mounted on hinges 2-5. At the same time care must be taken to shelters do not coincide with the position of the shelves and the housing jumpers.

The procedure works:

1. Make marks on the doors, marking the spot fixing canopies indented from the edges of the product in the 70-120 mm.
2. Awl outline central point and cut the endmill at a right angle bearing seat depth of 12-13 mm (shown below). At the same time care must be taken to 16 mm panel to make a through hole.
3. Attach the canopy to get the groove and check how it free play. Awl on wood surfaces chop mark through hinge lugs for precise planting screws.
4. After all the shelters makeshift door is applied to the assembled cabinet, on its side walls are marked attachment points. Stake the points obtained, can be screwed fittings and proceed to install the next door.

Assembling the finished set

When all the elements of the headset is ready to be installed, you can begin final assembly and decoration. Primarily mounted lower tier from extreme or corner cabinets. In this case, the upper edge should be checked on a horizontal level and match the height. Mounted fixed number of cabinets special couplers 5 mm. On top of the stone countertop is laid and fastened with screws. On the surface you need to mark up and make holes for the sink and stove.

The top row of cabinets should be at a height of not less than 65 cm from the tabletop. Given this requirement, the sizes and the modules mounted on the upper fastening point on the wall assembly is installed tire. Boxes themselves must provide universal rear wall of canopies, departing from an upper edge of 5-6 mm. After hanging cabinets their arrangement is adjusted to match the full level in the vertical and horizontal directions. If desired, the inlay can create unusual furniture, for example, used painted, or printing technique decoupage.

Interestingly look facades having inlay formed by applying artificial aging or patina surface. Such methods suitable for Provence or country style.

On the role of decoration can handle exquisite furniture handles, linings made of wood and contrasting edges. But if you want something unusual, design ideas homemade cuisine can spy on the photo on the Internet. Update the furniture and glass elements to help with unusual decor - stained glass cabinet doors or painted apron above the working area.