Furniture the hands of chipboard: what is important in its manufacture?

One of the important subjects cuisine is set. Create it any person, even a layman of the business. The main thing to remember that the thickness of kitchen furniture must be at least 25 mm. For its production required the bars and the boards with the treated edge. Make kitchen furniture made of particleboard is not difficult. This will not only save money on the purchase of kitchen furniture, but also get an exclusive and original product. In addition, designer furniture, made with his own hands, it is very much appreciated.

How to choose the right stuff?

The range of any building shop you can find a lot of different types of particle board, which usually differ in mass and density. To create your own hands normal stools, small shelves suitable conventional plates and dining table, wall units and cabinets need high-quality material.

In addition, during processing DSP should only use proven tools to prevent splitting plates. It is also important to consider the next time, if the manufacturer has carried out low-quality pressing, then the risk of splitting the material increases in the cut. There are several options for the tool used:

1. Hand saw. This tool should be only a fine-toothed. It should be kept at an acute angle. Indeed, precisely because of this cut is carried out more smoothly, without any damage.
2. Circular saw and jigsaw. The process is performed at high speed, the pressure on the tool to be rendered maximum.

For comfortable work, you can also apply a variety of special adhesive tape, adhesive tape or electrical tape. With a sharp knife incision is made so that there was a small pit in the plate.

Immediately after the cut has been processed, on the surface must walk file. All movements are produced toward the center, as in this case, cause any damage is almost impossible. In the absence of a file, you can use fine usual sandpaper zero to finalize.

DSP necessarily need to process, as this material is highly toxic. It is best to purchase chipboard, laminated after coating is safe and protects in most cases from the negative effects, but the end is still open. From this situation, there are four outputs, such as PVC film, edge, plate or melamine edge.

Edging Particleboard

Before you make the layout with their hands and begin to collect kitchen units should do the treatment chipboard edges. Usually they paste over melamine edge. On one side of the tape has an adhesive, so it is immediately ready for use. According to the technology, the edge is treated with iron, with a little heating the upper part of the strip. In the process should be accurate and careful, since the device is extremely hot. Furthermore, it is important to adjust the temperature, because when the high index adhesive may boil away completely, and the low - edge not bonded to the sheets.

Thickness chipboard for kitchen furniture can be completely different. The best option for the headset can be regarded as 25 mm. After the edge to be treated, the extra edge to be cut. To do this, you can take an ordinary stationery knife and a piece of paper. Then you need to take nazhdachku and walk her in the corners, thereby completing the processing. Prokleivat edge you need in order to they do not get wet, which is able to destroy the material.

Applying the correct markup

It is necessary to pay special attention to the correct markings and the alignment of the holes in the particle board in the center, because it depends on how it will look next set. Be sure to mark up all the points for joining sheets and pens. This will require a wooden ruler, one side of which is attached to the rake angle of 90 degrees.

Before starting work on it to drill small holes in size. In order to connect the sheets must make a note of the central holes on both sides, and then using evrovinta fasten them together.

How to connect the parts?

Production of kitchen furniture made of particle board with your hands is not an easy process. Indeed, it includes a large number of connection parts in different ways. The most common ones are:

• butt-mounting parts;
• "dovetail".

The easiest way to connect - it's fixing butt. This method chipboard edge fixed by a special glue and fasteners of all kinds, but it is not a solid.

Optimal and easy way of fastening parts of kitchen furniture made of particleboard is considered to be rebated. Grooves can be done in any direction and along and across.

Mounting of drawers with guide

Currently, there are a lot of all sorts of guides, which are used during the installation of retractable structures. They facilitate the movement of boxes. With frequent use of smoothness and durability can guaranteed only roller made of metal.

During the manufacture of furniture made of chipboard kitchen with his hands, clips species pictures will not be superfluous for boxes. Thanks to them, you can finally decide on the future structure. After selecting a track, it must be correctly installed in a cabinet or a drawer. For fixing screws can be used, which are usually bundled together with the rollers.

In addition, we must remember that the guides are longitudinal and circular holes. As a general rule, the installation start directly with longitudinal as well, you can achieve the desired position.

After adjusting the guide roller should fix it through the round hole. at creating a project for kitchen furniture his hands can be set, which not only successfully fit into a room the size, but will be useful in all respects. In addition, the price of such furniture usually comes well below the cost of the headset is made at the workplace.