How to apply wallpaper: tips and tricks for stickers of wallpaper coatings

How to apply wallpaper (51 photos). Surface preparation. Pasting plastered and painted surfaces. Preparing the canvas and gluing

X

Table of contents

  • 1 surface preparation
    • 1.1 plaster walls
    • 1.2 If the walls are covered with paint
  • 2 The process of preparing wallpaper
  • 3 adhesive Application
  • 4 stamping
  • 5 Summing up
  • 6 Photo Gallery

Decorating the walls - one of the most important stages of repair. In search of an answer to the question of how to apply wallpaper, we turned to the experts for advice. So, proper wrapping the walls - the theme of today's article.

surface preparation

how to apply wallpaper

Your attention! Before starting the work necessary to process the surface, which will glue the wallpaper for that. This is the first condition - the high-quality finish.

The walls and ceiling must be flat, smooth, dry, clean, free of cracks and normal porosity. Earlier pasted canvas must be removed, and on the surface, apply a primer.

plaster walls

The wall surface must be clean, dry and light, so it becomes after plastering. If you doubt whether the surface is dry, glue it to the plastic wrap and leave at 12 o'clock.

After this time, look at the inner side of the film, the presence of drops indicates the need for drying and ventilation company premises.

removal of Nabeul

removal of Nabeul

If the plaster absorbs moisture, be sure to apply the primer. Before pasting paintings all concrete surfaces must be primed.

In the presence of surface defects:

If cracks need to be expanded to apply a layer of putty strip of fabric on top of another layer close putty.

If the walls are covered with paint

Tip! First, check how firmly held layer of paint on the surface. You can use duct tape - glue it to the surface and pull sharply. If on a tape there were small pieces of paint, the old finish must be removed.

Otherwise, the surface to be treated with alkali solution and wash well with warm water. Necessary to plaster the wall, then the adhesive grip with the surface will be much stronger and walls wallpaper pasting process will be easier.

The process of preparing wallpaper

The first rule - mandatory checks on the identity of the party rolls, color tone.

The process of bonding webs

The process of bonding webs

After confirming the presence of a suitable material, it is possible to start cutting webs. Length is determined, focusing on the height of the room. To the resulting figure is added 7-10 cm.

If you purchased fabric without a pattern, all of the bands may have the same length.

In case if you need to combine drawing, carry out the following work:

  • The first web is cut with a knife wallpapering.
  • Before the second cut cloth, check if image point. If you get a direct docking, all the other bands will be the same for cutting out and figure you just need to be combined with each other.
  • Raskraivaya Image-registration, the image will be on each band shifted by half of the pattern, each second band will be the same. It is important that rolls unwound in the same direction.
  • To the blade is not messed up, number them and mark the top.

Today, most paintings glued back to back - they do not overlap each other.

adhesive Application

Glue is recommended to use depending on the type of paintings, their weight and the type of surface.

Rules of Application:

  • Cloth place face down on a clean dry surface.
  • The adhesive is applied from the center to the edges. To evenly distribute the follow Figure eights. Be sure to carefully consider the edge of the strip.
  • Fabric glue fold inward and repeat the procedure with the second part.

Wallpapers need some time to be folded to impregnate. The heavier band, the longer it takes for the impregnation to the immediate glueing.

stamping

Tip! Begin the process of stickers from the window. The first glue strip via plumb vertically to the remaining webs were smooth. Near the ceiling leave the reserve.

adhesive application

adhesive Application

  • In order not to appear bubbles, streaks are well pressed down and carefully straighten the soft wallpaper brush or roller from the middle to the sides.
  • If stains on the obverse surface blot damp sponge.

Watch out for the lack of drafts. Organize ventilation in the room is possible only after the complete drying of the coating.

  • Wallpaper paste on the ceiling of the light from the window and moving into the room.
  • Be sure to find a companion who will hold another portion of the web.

And the final stage in the process of gluing vinyl wallpaper - gluing borders.

Used in relief paintings and wondering how to stick the borders? In this case, after bonding border canvas fitted on the height of the room. To smooth the wallpaper, this rule is irrelevant, so border can stick directly to them.

To verify the density of bonding the edges of panels, swipe roll joints.

Summing up

This article provides tips for Wallcovering that will perform all the work correctly and as quickly as possible. We hope our article has been helpful to you. In order to more accurately understand the technological and practical issues on our website provides detailed photo and video instruction, in which you will find useful information on the question.

Photo Gallery