Little by little own drawings and photos: wells to do, cleaning video, to make a drilling device

The self-made bailer for the well allows the wellbore barrel to be cleaned from accumulated sludge in a timely manner without resorting to outside help. Wells in the private sector have to be treated in a special way. If some parts of the source melt, then the productivity of the well is reduced, which means that certain volumes of water are lost, it becomes clogged, etc. So, for disinfection and purification of water, some special equipment will be required. In particular - a bailer, which you can make yourself.

Description: the device of the cleaning bailer

To clean the hole without assistance, a cleaning structure is needed, the manufacture of which is not very difficult. In order not to use the drilling rig, and you need to trowel. And certain materials are required for this.

The pipe with an internal diameter of at least 60 mm and a length of at least 80 cm;

Ball of metal, its diameter is 40 mm;

To the bottom of this pipe, a thick washer with a funnel seat is welded to the diameter of the ball;

The lower part of the pipe can be flat;

The ball should be placed inside the structure, the top should be welded with a grid of thick wire that opposes the ball drop.

A metal arc that serves as a cable holder or a special lifting cable will be fixed immediately. For manual cleaning of the well it is possible to make an independent mechanism, with which it is really possible to cope alone. And even more perfect will be such a ball mechanism, if special tools are welded to the bottom of the pipe. They will begin to loosen the dirt and all the accumulated sludge when the structure is immersed in the source.

Bearing on the self-cleaning bailer

A bearing is a metal ball that sinks inside the pipe. It is sealed on both sides. Sometimes it is difficult to find it on sale, but you can do it yourself.

The hopper is an efficient and relatively simple drilling tool for cleaning private sources of water from bottom contamination.

It will take lead shot or simply old bearings from anything. Also, you need to take a rubber ball that matches the size, cut it into two parts. Then fill the material, then all the glue on the iron, connect the two halves together.

After the homemade design has dried, you need to remove the rubber. Grind the resulting element on the machine. It can also be used for bailers. The design will be strong, you can safely hope that it will last for many years.

How to drill a bailer

The bailer should have a long length to clean its bore well. And this length will be 4-5 m. The valve for such a manual installation can be made from a steel plate. And that the seal was more qualitative, use a natural leather or simply rubber from an automocamera.

The harrow is a tool used to clean the bottom of a well from small debris of rock, sand, silt, as well as soil saturated with moisture

Instead of a rope or rope, drill rods are used, making them from gas pipelines definedSegments. The diameter of such structures is 33-48 mm.

Can, by the way, instead of metal bars use and wooden appliances. There are cases when ash, larch, and spruce were used. This is an effective option, but it is very costly in time and forces to perform. Therefore, look at the photos and drawings that are more accessible for making the designs.

Simple bailer for the well with your own hands, drawings and photos

So, the bailer can be with a flat valve or round. Different materials, sizes, diameters are used. And how does the cleaning process go directly?This process is reliable, but time-consuming. True, only the first time usually it seems complicated, then everything goes on a rolled-up scheme.

• Install a tripod above the borehole, attach a block above it;
• Tie a rope to the bailer through a carabiner or a strong rope;
• If the bailer is very heavy, then a swivel or winch is used;
• Pull the cable through the block, lower the bailer to the bottom of the borehole;
• Do not do this with a swing, hold the cable so that the bailer does not jam;
• It is recommended to work in tarpaulin gloves, so that the rope does not injure hands.

When the bailer has lowered to the bottom, lift it to a height of 50 cm and sharply lower it. The valve opens when you hit, the water with sand will rise inside your bailer. And to do this lifting / lowering it is necessary until the bilge is full. You can feel its filling by weight. Therefore, the bailer is removed and cleaned. It turns out that it works as a spoon or as a suction device that helps break through the silt bottom and clean it.

How to make a bailer with your own hands( video)

Using well-verified drawings, using good tools and materials, you can build a bailer that will regularly clean the borehole. The process is laborious, but technically not the most difficult. Once you have done a good job, you can save on the expensive services of well cleaners.