Installation of a hydraulic accumulator for water supply systems by one's own hands: connection to a submersible pump, a diagram of a well

Before installing the accumulator, it is necessary to familiarize yourself with the recommendations of specialists. The hydraulic accumulator is needed to create pressure, storage of water, which is useful for guests in the house in case of water supply cut-off, and reduction of water hammers in the networks in the suburban area. The device looks like an ordinary tank with a mechanism for creating pressure.

Process of connecting the hydraulic accumulator

If the accumulatoravilno connect, then all further maintenance you can do yourself. Therefore, correctly connect this device, so that later do not suffer during its operation.

A non-return valve must be used to connect the accumulator. The battery tank is connected to the submersible pump, so the valve will not allow water to flow. It is also possible to select a deep Gilex pump, which can be lowered to the bottom of a well or well. Of course, there are other types of pumps. After all, the pumping unit is also capable of pumping air for the pumping station. We will analyze the usual case of mounting the accumulator.

When connected, the accumulator must be disconnected from the socket

Hydraulic accumulator connection mechanism:

1. We measure the dimensions of the accumulator;
2. We get the scheme of water supply and heating pipes;
3. We are looking for a free space for installation in accordance with dimensions;
4. From the options found for the installation, leave a place that is closest to the pump;
5. We connect the submersible pump with the accumulator.

Thus, you calculate the location for installing the accumulator.

Remember that the water pump should be lowered below the water mirror level by no more than 30 centimeters.

The device should be as close as possible to the water pump. As a rule, the accumulators in this case are located at the entrance to the holiday home. To subsequently maintain the accumulator, it is necessary to calculate its integration into the system of cold and hot water. This need is associated with the dropping of water from the tank. Therefore, be attentive to the installation site.

Is the installation of the

accumulator easy? The gardeners immediately panic when they hear that the accumulator must be connected to the water supply system. They think that suddenly the pipes can burst, and then the entire dacha section with the house will be filled with water. This is not true.

The hydraulic accumulator is installed according to a standard and well-developed scheme. A lot of summer residents integrated their tanks into it. And perfectly coped with the task. To do this, they acquired all the necessary components in the form of nipples, pumps and fittings.

In Denmark, Germany and Italy, hydraulic accumulators are put in basements for 50-100 liters.

One person is enough to install the accumulator

To put it in the right place, you need to determine the water flow rate for the whole house. Determine the pump capacity and the volume of the accumulator. It is also worth knowing the location of the main water supply units.

Next, you must write a list of what you need to buy to install the tank:

• Hoses;
• Pipes;
• Fittings;
• Nipples;
• Cranes and so on.

Then look at the diagram of the installation and just do everything as indicated there.

At first glance, it seems that installing the tank is a difficult task. This is not true. Decide on the place, look at the scheme that has running water. Buy the components for the connection and simply connect the tank to the common water supply system.

Is it possible to make a hydraulic accumulator by myself

Many craftsmen make a hydroaccumulator with their own hands. To do it yourself, you need to understand its structure and design.

The accumulator is a container with a certain volume. Its structure is quite simple and does not represent anything complicated. We have a tank of only two main parts.

The structure of the tank is:

• Membrane;
• Rubber pear.

You can only make a hydraulic accumulator if you have the experience

The tank can be made of plastic or aluminum. Inside the tank material should be smooth and even. If there are roughness in it, then the inner membrane or pear will simply stretch, which will lead to its destruction. There is also a membrane-free storage tank, in which there is no membrane. But such a tank is less effective. The presence of one membrane expansion tank can solve many problems in water supply.

The tank should be selected with a volume of more than 30 liters.

The tank requires a pressure switch and a pressure gauge that can be found at a modest price on the market. For connection, take also fittings, quadrants, tees and a crane. In the store for their sale, ask to select only high-quality models, because there are different types. As a pear or a membrane, you can take a bicycle camera - a nipple. Also you should have a rubber sheet and sealant.

To not buy a tank and save your money, you can make it yourself. To do this, it is sufficient to find a tank with a volume of more than 30 liters and components in the form of sheets of rubber, fittings and tees with cranes. So you will build a good tank for the water system.

We disassemble how to connect the accumulator to the

submersible pump. In order to correctly connect the accumulator to the submersible pump, you first need to understand the connection mechanism theoretically. This will help to quickly perform the work of connecting the pump to the tank.

Connecting the accumulator to the water supply system is not difficult. To do this, it is enough to have all the necessary elements, valves, hoses and connect them sequentially according to the algorithm.

In order to connect the tank, it will be necessary to check the availability of:

• Downhole pump;
• Relay;
• Pipelines for the flow of water from the pump to the future tank and from the tank to the water intake points;
• Check valve;
• Stop valves;
• Water purification filters;
• Drainage for sewage.

Pipes for connecting the hydraulic accumulator to the submersible pump are sold in any construction shop

Before installing the tank, check that all necessary tools and components are present.

If all of the above you have in stock, then you can proceed with the connection. A transitional nipple is connected to the submersible pump. Next is the connection of a non-return valve and a pipe. Then put a fitting and a filter, and between them a tap. After them, install the five-needle and the pressure switch. A manometer is needed for monitoring. It helps to adjust the pressure. To the accumulator you connect a drain cock and a hose that withstands vibrations during operation. This completes the installation. In this case, the well goes to the background, because all the main work is transferred to the domestic water supply system.

Dacha owners sometimes install a tank on the wall. To do this, put the tank on the mount.

It is not difficult to connect the battery to the pump. The main thing is to check the availability of all components for connection to a submersible pump or for a downhole pump. Otherwise, you have to stop working. The connection process can take only a couple of hours, if you do it in the right sequence.

What is the connection diagram of the accumulator

To connect successfully, you need to do it according to the scheme. Learn what you need to connect, what elements and details, and also, the instructions and connection scheme will help you.

In order to know what and where to connect, you must first become acquainted with the main components of the connection scheme. Around the whole process is being built. The purpose of the circuit is to show how the accumulator is connected to the common circuit.

The connection diagram of the accumulator has three main elements:

1. Self accumulator;
2. Submersible pump;
3. Pressure switch;
4. Five-wire choke.

The connection diagram of the accumulator can be easily found on the Internet and printed on the

printer. These are the main components of the wiring diagram. When collecting the hydraulic box, take into account the automation of the tank, put a hose connection and an additional fitting if necessary, help in the reliability and tying. The hydraulic pump is better to connect the pressure to the relay in the last stages, so the voltage is connected to it. The relay is connected to a five-way connector. A non-return valve is also attached to it.

Remember that the relay is powered by 220 V AC mains. Be careful!

The hydroaccumulator is attached to the other end of the union. From it goes the pipeline into the house in the taps. The manometer is used to analyze the condition. It can be installed on a five-branch choke. Usually it already has holes for installation.

In this scheme, you quickly and without problems connect all the main elements. Do not be stingy to buy a good submersible pump and make a selection of a quality accumulator. These are the components worth spending money on. In this case, they will serve you for decades.

How to connect a hydraulic accumulator for water supply systems( video)

A hydraulic accumulator for a water supply system is necessary if you want to have permanent access to water in your home. It will adjust the pressure in the water supply network and give you the opportunity to enjoy pure tap water. A small capacity is easy to install, and there are many benefits for a private house. Buy a hydro accumulator and you will always have a constant supply of water in the house.