As plasterboard putty: correctly applied to the GCR with their own hands, technology roller, preparation and which layer

It is more difficult to work manually: the mixture will have to be poured gradually and the water should be poured too carefully, all very carefully mixing, as if you were mixing the dough. It is very important that no air bubbles remain inside.

Drying putty very quickly, so it's better to cook it in small portions. To half an hour you could spend the divorced mixture, and only then went to a new kneading. And economically, and technologically correct.

We do the right thing: how to apply shpaklevku to drywall

Work often begins( or reduces to this) with sealing joints. To do this you will need two spatulas - wide( 35 cm) and medium( 15 cm).It is often used grater and trowel, but with them you need to be prepared for the fact that the work will be delayed and not the fact that the result will be ideal.

In order to correctly apply the putty on the wall, you will need two different spatulas In order to correctly apply the filler to the wall, you will need two different spatulas

All process technology is as follows:

  • Type a thin putty putty, gently transfer it to the seam;
  • Then take a wide spatula, and stretch the material as widely as possible;
  • After several joints have been processed, it is possible to arm with only a wide spatula, this will save time, but you need a skill.

At this moment, it is impossible to leave unevenness and smudges on the surface of the GCR.It will be hard for you to remove them, so you can injure the material. Because the work requires maximum accuracy.

Main surfaces: how to putty plasterboard

Only after the starting layer has completely dried in the corners and joints, it is necessary to putty the main part of the plasterboard. First, the outer corners are strengthened by aluminum profiles. They are installed using a construction stapler and putty.

To level the putty on the wall, experts recommend a wide spatula We recommend to level the putty on the wall with a wide spatula

The material is applied to the wall and is spread out with a wide spatula. Move from top to bottom. If the room has arches or other complex structures, be sure to use a plastic corner. It is fixed with braces, and then shpaklyuetsya.

Work as fast as possible in order to be able to trim the adjacent trim strips in the process. After the putty is applied, allow the material to freeze.

It is worth saying that shpaklyuyut drywall sometimes and roller. This is done when you need to "whiten" a surface that has already been leveled to give it an even color for the subsequent work. But more often it is necessary to work as a platen.

Putty: finishing work

When the puttying is completed, do not rush with the subsequent finishing. The surface must dry thoroughly. Then all irregularities must be treated with small sandpaper. Be sure to do this in goggles and a respirator.

Before you begin the final finishing of the walls, you need to wait for the complete drying of the putty Before starting the final finishing of the walls, it is necessary to wait for the complete drying of the putty

Then proceed as follows:

  • Process the surface already with zero emery;
  • Then apply a smooth primer layer;
  • For the finishing use a special mixture, or the starting mixture dilute to the state of sour cream;
  • Apply and stretch the material with a wide spatula - the putty layer must be thin and even;
  • After the drying of this layer, it is necessary to again make the treatment with a primer, and only then you can glue the wallpaper or paint the wall.

With a surface treated in this way, you will easily remove the wallpaper on the next repair. Gypsum cardboard in this case, nothing is threatened. Ready to remodel is not worth it, even if there are small defects. Perhaps, it will be enough to grind or smooth out the finishing composition of a small area.

Instruction: how to putty plasterboard( video)

Putty plasterboard is necessary, and do it according to all rules - with preparation, priming, grinding. Do not skimp on the layers, on the material, the final form of the whole work depends on it.

Good results!