Repair of plastic windows with your own hands

Sooner or later, but every owner of housing in which plastic windows are installed faces the need for their repair. Approximately 5 years later, any, even expensive accessories begin to be shattered. With insufficient care, the sealant may begin to crumble. Glass can knock out the younger generation. And the adjustment of the clamp should be done 2 times a year. In this article we will tell you how to repair plastic windows with your own hands.

glass unit Repair of a broken handle

Most often, the handle breaks first when the plastic window is reinforced. It often happens that during the operation the window sags and the tenants, instead of regulating the sag, begin to press the transom into the frame with effort, acting on the handle. The handle, of course, can crack or just stop turning.

If there is such a trouble, first of all you need to find and eliminate the cause of the failure, and then adjust or replace the pen itself. To do this, turn the plate covering the fasteners by 90 degrees. Here it is necessary to act according to the degree of breakdown. If you just need to tighten the loose handle, then you need to pull a screwdriver with self-tapping screws. If you plan to replace the handle, the screws need to be unscrewed, the handle can easily be removed and a new handle installed in its place. This procedure for repairing the plastic window with your own hands will take about 15 minutes. 15.

Adjustment of PVC window clamps

The clamp is usually adjusted with the change of the season. For the winter the transom is pulled to the frame denser, weakened for the summer. In no case should you leave the winter clip for the summer, because this will lead to the destruction of the seal due to excessive load. Adjustment of the pressure of the plastic window occurs in each brand differently.

For example, for self-adjustment of the ROTO fittings, a 6-key furniture key is required. On the perimeter of the transom, you need to see where the locking pins are located. Each trunnion has a notch. To adjust for the winter, the notch should look towards the street, to adjust for the summer - towards the room. For more details, see the article on adjusting plastic windows.

Replacement of the sealant with your own hands

You should look after the seal of the plastic window at least 2 times a year. In the spring and autumn it should be wiped with a wet rag, it can be lubricated with silicone grease with dust and dirt. If this procedure is not carried out, the sealant will begin to crumble, collapse, which will affect the heat-saving characteristics of the plastic window.

Sealant is sold in building supermarkets. At purchase it is necessary to consider, that on a window 2 contours of a sealant: internal and external( on a leaf and on a frame).Both need to measure with a tape measure. After buying a new neatly removed the old, in its length you can cut the length of the new one. We wash the window under the old seal. From the top down, we begin to insert the seal into special grooves, pressing it with any suitable tool, for example, the back side of the scissors. It is not necessary to stretch the material especially. Seal joints are glued together. This kind of repair of a plastic window can be done without problems with your own hands. For this you can read the article about replacing the sealant on plastic windows.

Repair( replacement) of accessories

Most often, adjustment of the hardware is necessary when the sash is sagging. When sagging, the leaf begins to touch the frame when opening / closing. You need to adjust the main nodes, which slightly differs from each manufacturer. On any eccentric on the leaf, the name of the fittings manufacturer is written. The most common are ROTO, Siegenia-aubi, Maco. On the manufacturer's website, it's easy to find step-by-step instructions for this type of PVC window repair.

Replacement of broken double-glazed windows

If one glass in a double-glazed window is broken, all the same it is necessary to change completely a double-glazed unit in gathering. Perhaps this is the most expensive type of repair of plastic windows, so for those who want to save, it is better to do it yourself. To begin with, you will need to order a double-glazed window in a factory or in a specialized firm. To measure a double-glazed window it is not necessary to pull it out, it is enough to measure the distance between the extreme points of the clamping beads and subtract from each result by one and a half centimeters. For these parameters, you can order a new double-glazed window.

For dismantling the old double-glazed windows, the long vertical beads are first removed with a chisel. To dismantle the bezel you need to start from the corner. The gaskets must be retained for a new double-glazed unit. After the dismantling of the glazing beads, the double-glazed window is easily pulled out, and the frame is washed with a soap solution. Now you can install a new double-glazed window and again - staples in the reverse order. The fillets are inserted into the grooves with light punches of a rubber kiyanka. In more detail all is painted in the article about the replacement of double-glazed windows with own hands.

Now you see that the independent repair of plastic windows - the procedure is fearless. Video and photo repair of plastic windows with their own hands will help you to perform all necessary operations.