Interior decoration of the frame: photos, examples

After the construction of the wooden house, the next stage is the work on its interior decoration. The quality of their implementation should be given special attention, since the quality of the work will depend on the comfort of human stay, the heat and sound insulation characteristics of the premises, as well as the aesthetic appeal of the house.

Features of wooden frame finishing

The need for interior finishing is caused by the followingreasons:

• as a result of finishing works, the house becomes more attractive;
• no finishing significantly reduces the period of operation of the building. In the presence of insulation on the main material, from which the house is erected, there is much less load, which as a result contributes to the preservation of the structure;
• finishing improves the heat-insulating properties of the house, therefore, the performance of these works will not only help create a comfortable indoor temperature, but will also significantly save money on heating.

You can not proceed to finishing the log house immediately after the construction is completed. It is necessary to wait a certain period of time - from 1 to 1.5 years until shrinkage occurs at home. Upon completion of this process, the building will be ready for indoor work.

However, among the options for finishing, there is a way to reduce expectations and perform appropriate work after the completion of construction. This method consists in processing the ground log with paint and varnish. This makes it possible to save time considerably. Doing this in such a way is advisable if the frame is warm enough and there is no need for additional insulation, and also in the presence of even walls.

The advantages of this process are as follows:

• it becomes possible to start working immediately after building a house;
• simplicity of operation;
• no significant costs.

The disadvantages are:

• impossibility to hide communications;
• complexity in the process of finishing absolutely flat surface of walls;
• fragility of the coating.

This finish needs to be updated every 5 years. By this time, it will be possible to use other materials, since the shrinkage of the log structure will be completed definitively. Consider all available materials with which you can finish.

Features of work with clapboard

This kind of material is a board thickness of up to 220 mm, which are produced on the basis of hardwood and pine wood. The lining can be installed in a horizontal and vertical way. To determine the most appropriate method, you should proceed from the dimensions of the structure:

1. For small houses, vertical placement is a suitable option.
2. If the construction has large parameters in this case it is better to stop on horizontal mounting. This condition is due to the size of the material. The length of the lining is 2.5 m. If the laying method is not suitable, joints are formed.

The following features should also be considered for the finishing of the log cabin:

1. Before proceeding to work it is recommended to carry out processing of the lining with special preparations protecting the material from fire, as well as the negative impact of insects and moisture.
2. It is recommended to mount the lining on the lathing. Thus, the stacking will be as flat as possible, moreover, it is possible to hide communication behind the frame. The presence of a billet is not mandatory if the house is built of glued or profiled timber, since such walls themselves are quite even.
3. For battens use bars that are placed along the entire perimeter in a horizontal way, while observing a distance of 50 cm.

Begin the interior of the log from the corner of the room. Thanks to the coupling "spike-groove" the laying will be carried out smoothly and will not require much labor. There are three methods of fastening the boards to the crate rails:

1. The most high-quality method is fixation by means of a special clamping device called a claymer. One part of this product is fixed inside the groove, the second part is to be connected with the strip by means of a screw.
2. Also fastened with galvanized nails. Under a suitable slope of 45 °, the nail is inserted into the groove and clogged.
3. The last third method involves the use of a self-tapping screw. In the board it is necessary to make a hole, the diameter of which must correspond to the screw of the screw, and the depth should be equal to half the thickness of the board. Then screw into the hole and close the screw. After that, you need to align the font with the board by grinding.

Application of lining has both advantages and disadvantages. This material is easy to install, environmentally friendly, creates additional insulation and has a natural appearance. But at the same time the lining is a rather expensive material and the boards must be treated with special preparations before work.

Finishing of log cabins. Photo:

Rules for finishing using the rope

This option can only be used for a log house built from round logs. The presented method of finishing is carried out with the help of a jute decorative rope and requires compliance with certain rules:

1. It is necessary to start work only after processing the bar with antiseptic means.
2. The rope is laid in the crowns of the structure. This decoration helps to keep heat inside the building, and also prevents the entry of wind and moisture into the structure.
3. The rope is fastened in several ways:

• by means of staples;
• with glue;
• due to special nails.

The inner lining process is as follows:

1. The rope must be treated with an antiseptic before installation. Next, you need to cut off the fragment of the required length.
2. The edges should be wound with threads and treated with a varnish or glue in order to avoid their dissolution.
3. For fixing a special thermal adhesive is used, which is applied with a gun. Apply the glue on the uneven bars in the places where the rope is fastened.
4. After you need to lay on the adhesive composition of the rope.
5. In parallel, it is necessary to drive into it nails of small size - 15 cm - 20 cm.
6. After finishing work, the rope and logs must be varnished.

Rope has such advantages as:

• acceptable cost;
• reliable protection of logs from cold penetration;
• originality and decorativeness.

However, the following are the drawbacks of this material:

• a laborious installation process;
• impossibility to hide communications;
• difficulties in thermal insulation with other materials.

Special features of the

house unit The installation of this material is similar to the lining of the lining and suggests the following sequence of actions:

1. Finishing of the log house inside is carried out on the cage frame.
2. Begin work from the bottom and move in the upper direction.
3. The last board will need to be cut, at the top of the wall it will be less obvious.
4. It should be noted that the block of houses is stacked exclusively in a horizontal way.

Advantages of this material are such features as:

• authentic imitation of the present hut;
• simplicity of laying;
• the ability to insulate walls and hide communications.

The disadvantages of the Hausa unit include:

• high cost;
• unnatural appearance in case of improper installation.

Finishing method with

putty. Although this option is used in most cases for walls made of bricks, this method can be used for finishing buildings from a log house. In this case, it is necessary to use a plaster composition on a mineral or acrylic basis. Putty creates a coating that protects the frame from the effects of destructive factors. Also, with the help of special components, the composition can be given the desired color.

The process of finishing is simple: first you need to attach a grid to the frame by means of screws, and apply plaster on it. This method makes it possible to level the surface of the walls.

The obvious advantages of putty are low cost, large choice of colors. The process of applying the composition does not require special skills and knowledge, a layman can quite easily handle work, moreover, in the shortest possible time. But this finish will last for a relatively short time - about 5 years. Also, it will not be possible to hide the pipes completely, and the decoration as a whole will not have a pronounced aesthetic appearance.

Application of drywall

This material is used as a decoration for a log house quite rarely, because in this case the characteristic impression of a wooden house disappears. But in some cases this move justifies itself. The lining process has the following features:

1. Drywall is mounted on a lath made in the form of a U-shaped profile.
2. It is recommended to lay a heater, for example, glass wool, between the log house and plasterboard.
3. The material is then fixed to the profile by means of screws.
4. After the end of the installation work the joints should be puttied, this will ensure a smooth surface.

As the advantages of gypsum board material, the following factors can be distinguished:

• the possibility of making holes and protrusions in the wall at will. This will make it possible to hide pipes and wires and implement any design solutions;
• also this material is characterized by low cost and ease of installation process.

Among the shortcomings should be allocated comparative fragility, t.the material will last from 15 to 20 years. In addition, the need for additional insulating materials, the instability to damage and the elimination of the characteristic atmosphere inherent in houses made of wood.

Finishing with plastic

This material is suitable for finishing individual areas of the log house, however, not for its full lining. The plastic is mounted in a horizontal and vertical way. The most common last option:

1. At the initial stage of the work you need to build a frame. Panel products will be attached to it.
2. The profiles must be attached at the top and bottom of the frame.
3. You need to start the installation from the corner. The panel must first be welded into the profile, after which the grip occurs.
4. The panels are attached to the profile using self-tapping screws and nails. To improve the connection of plastic panels, use liquid nails or glue.

The advantages of plastic as a finishing material are such features:

• ease of installation;
• affordable;
• the ability to hide communications;
• sufficient choice of color gamma.

However, the plastic material also has disadvantages:

• slightly flammable;
• insufficient resistance to mechanical stress.

Conclusion

Interior finishing is essential for the subsequent operation of the log house. First of all, with the help of finishing materials, it is possible to solve aesthetic tasks and arrange the house according to your preferences. In addition, the finish has a practical value for the log house. It will create an additional insulating layer and will help maintain a comfortable temperature in the room.

Interior decoration of the log house. Video: