Errors in the washing machine Siemens: error codes f17, f23, f57 and frequent malfunctions

click fraud protection

Code

What the possible causes of

also mean What to do

F01

The door is not closed tightly enough.

Check the door and close it denser, and if it prevents the laundry, release the machine from some of the things.

F02

No water supply due to:

  • Closed tap;
  • Weak water pressure;
  • No water in the pipes;
  • Litter in the mesh filter of the water supply hose.

Detect the blockage in the hose and eliminate it, and also check the water supply.

F03

No discharge of water due to:

  • Discharge in the drain system;
  • Malfunction with drain pump;
  • Problems with the electrical controller.

Clean the filter and sockets of the drainage system, and also check the serviceability of the pump and the free rotation of its impeller. Faulty pump replaced working part. If the draining unit is OK, check the electrical controller.

F04

A water leak has appeared.

In search of a source of leakage, check the connections and the tightness of the tank.

F16

The door did not close, which prevents the start of the program.

Open the door and close it again, and restart the washing program.

F17

Water enters longer than required, due to:

  • Closed cock;
  • clogged filter;
  • Weak water pressure.

Check the tap, through which water is poured into the machine, as well as the water pressure. Inspect and clean the filter in the water inlet hose.

F18

The water is drained longer than necessary, due to:

  • Defective or clogged drain pump;
  • Breakdown of pressure switch.

Inspect the drainage system and clean the blockage in the drain pump, and if it is defective, replace this part. Check the pressure switch and its switch, and if the problem is with this sensor, replace it with a workable one.

F19

Water heats up longer than required, due to:

  • Faulty heater;
  • Low voltage in mains;
  • Formations on a lime scale heater;
  • Damage of connecting circuits of heating elements.

Inspect the heater and its associated wires, and if the heater is not working, replace it yourself or call a specialist for this purpose.

F20

Unplanned heater activation due to:

  • Temperature sensor faults;
  • Breakage of the TEN relay.

Inspect the NTC sensor and heater and replace the defective components.

F21

A malfunctioning of the control system, which causes the motor to operate unevenly, and the drum does not rotate. The situation is possible with:

  • Defective tachogenerator;
  • Breakdown of the reverse relay;
  • Short circuit in triac.

Evaluate the performance of the drive motor, tachogenerator and control unit, and then repair the faulty elements or replace them with running ones.

F22

The temperature sensor does not work due to:

  • Its breakdown;
  • Short circuit;
  • A break in its connections.

The washing does not stop, but the water does not heat up.

Replace defective sensor or repair its wiring.

F23

The activation of Aquastop occurred as a result of:

  • Hits into the water pan;
  • Connection failure of Aquastop;
  • Breakage of Aquastope.

Examine all machine nodes in which leakage is possible, and also check the operation of Aquastop and its connecting circuits.

F25

The aquasensor does not work as a result:

  • Formations on it of calcareous plaque;
  • Drainage system clogging;
  • Malfunctions of the pressure switch.

The washing does not stop, but the rinse cycle will be skipped.

Clean the drain system and the sensor itself, and, if necessary, replace the pressure switch with a working part.

F26

An analog pressure sensor is faulty or the pressure switch has broken. Also, the reason for such a mistake can be a break in the connecting circuits of these sensors.

Turn off the machine to inspect the sensors and their electrical circuits, then replace the damaged and defective items.

F27

Incorrect setting of the pressure switch.

Carry out the correct adjustment of the sensor, check its serviceability, as well as its connections.

F28

The flow sensor does not work.

Evaluate the operation of the sensor and its wiring, and if faults are detected, replace the non-functioning parts.

F29

The flow sensor can not lock the water intake because of:

  • Closed tap;
  • Too low water pressure;
  • Intake Filter Intake System;
  • Breakage of the magnetic valve;
  • Non-operating pressure switch;
  • Breakage of Aquastope.

Make sure that the tap is open, then check the water filling system in the machine, as well as the associated connecting circuits. Replace defective parts with new ones.

F31

Water level higher than normal due to:

  • Drain pump interlocks;
  • Breakage of the magnetic valve;
  • Drain Hose Locks;
  • Wrong settings or breakdown of the pressure switch;
  • Damage to the drainage system wiring.

Check the functionality of the solenoid valve, drain pump and pressure switch, and make sure that the drain hose is not pinched or dirty. If all nodes are OK, check the wiring.

F34

I can not close the door because:

  • It's stuck;
  • Its lock broke;
  • The door gasket has lost its elasticity.

Switch off the machine, then check the door lock, determine the mechanical obstructions for closing, and check the wiring.

F36

The door lock does not work, because the relay has tripped or the triac is broken.

Reset the washing program by turning off the machine, then check the control module and wires.

F37

The temperature sensor does not work( due to its breakage or breakage in its connections).

Replace defective sensor or repair its wiring.

F38

Temperature sensor does not work( due to short circuit).

Replace defective sensor or repair its wiring.

F40

An electrical problem( not valid parameters).

Check the power supply network and adjust its parameters.

F42

Due to the breakdown of the triac in the electronic module, the engine began to operate uncontrollably at high speeds.

Switch off the machine, run a test program and check the operation of the electronic module.

F43

Motor rotation stopped due to:

  • Tachogenerator faults.
  • Inhalation of the laundry inside the tank;
  • Drum locks;
  • Triac fires in the electronic module.

Switch off the machine, carry out the test program, then adjust the load of the laundry, tachogenerator operation, wiring and serviceability of the electronic module.

F44

There is no rotation of the motor in the opposite direction, which is often associated with the breakdown of the reverse relay or the breakdown of the triac in the electronic module.

Turn off the machine, run a test program and check the integrity of the electronic module.

F59

There were problems with the operation of the 3D sensor due to:

  • Breakage in its wiring;
  • Sensor faults;
  • Breakdown of the power module;
  • Errors Software.

Check the operation of the sensor, the power module, and the wiring, and then replace the damaged and defective components.

F60

The flow sensor does not work due to a breakdown of the sensor itself or the clogging of the bay system.

Check the flowability of the priming valve, the flow sensor and its wiring, and replace the non-functioning parts in the event of a malfunction.

F61

An incorrect signal is coming from the door, as it is loosely closed, a lock has broken or damage has occurred in the wiring.

After resetting the error one by one, check the closing density of the manhole, door lock and electrical circuits. Having identified the defective parts and wiring parts, replace them.

F63

Functional protection is broken due to processor failure or software error.

Cancel the program by turning off the machine, check the power module, and if it is defective, replace it.

F67

The card's coding is incorrect.

Cancel the program by disconnecting the machine, carry out the correct encoding or replace the card.

E02

Motor

does not work. Alternately check the resistance of the winding and the brush, and then the connection and finally the control module. Defective parts replaced with new ones.

E67

Problem with the encoding of the module( often associated with firmware)

Consult the specialist who reprograms the module. Alternatively, replace the module with a new one.

Errors of washing machine Siemens
  • Error codes
  • Frequent faults
  • Advice and prevention of breakdowns

Siemens brand technology has proven itself from the very best side, but even such high-quality and reliable washing machines from time to time fail. To the owner of the machine was able to quickly understand what happened to the device, a diagnostic system is provided in the technique from Siemens. On the scoreboard of the typewriter there appears an error code, deciphering which, it is possible to understand what the essence of the malfunction is, whether it is really possible to repair the device on its own or it is necessary to apply to a specialist.

Error codes

Frequent faults of the

Most often, owners of Siemens branded machines refer to repairmen for the following reasons:

  • Damage to rubber pipes.
  • Drain pump failure.
  • Failure of TEN due to scale.
  • Mechanical damage to the hatch.
  • Wear of bearings.
  • Burnout of the control module.

For replacement of the manhole cover, TEN and drain pump in the Siemens washing machine, see the video of Remstirmash company.

Advice and prevention of breakdowns

  • If you want to wash the machine from the outside, be sure to unplug the machine from the mains, do not aim for the water jet and do not use household chemicals with solvents or the presence of abrasive particles. It is best to simply wipe the machine with a damp soft cloth.
  • For the descaling of machine elements, use only specially designed for this purpose, taking into account their recommended dosages.
  • Regularly inspect the cuvette into which detergents are loaded. After seeing dirt or powder residue in it, remove the cuvette, rinse it and return it.
  • Check the pump pump status several times a year. To do this, remove the plinth panel, take out the drain hose and drain the water, then clean the pump and check the rotation of its impeller. Closing the pump cover, fix the plinth panel.
  • At least once a year, remove and inspect the strainer that is in the water supply hose to the unit.

Prophylactic measures shown in the Ukrainian program "Everything will be good" will help increase the service life of your washing machine.

instagram viewer