Decorative mill for the garden with their own hands. The best master classes

click fraud protection

Base part

The base of the decorative windmill with its own hands is made of three blocks, which are manufactured on the same principle as the upper blanks. The bottom block is a hexagonal prism without covers. The sides of the walls and the top are also cut at an angle of 450 and assembled with adhesive tape and glue. Between the opposite walls to attach screws or glue board, in the middle of which to install a square box with an inner side of 70 mm - for the axle beam.

15

16

The middle part will be attached to the lower block - a hexagonal pyramid without a vertex. The width at the top of each trapezoid is equal to the width of the wall of the lower block of the upper part, and at the bottom to the side of the hexagon. The side edges and the base of the 6 blanks are cut at an angle of 45 º and glued together as the very first manufactured block.

17th

The top element of the base is made on the bottom principle. On all elements of the construction are made in the upper part of the joints of the groove to install a viewing platform along the width of the bars of its frame.

18

All three blocks of the base are glued together into one structure and from above are set to oppress, but not too heavy, so that the seams of each of the blocks do not separate. Cut the glue.

19

How to make a decorative mill with your own hands. Photo

Observation deck

Prepare 6 bars of the frame, at the ends of which make small holes-marks for screws. Still need to cut 5 sets of slats for the platform track, which together make up hexagons of different sizes.

Tip! It is more convenient to make a drawing in advance with a marking on the board and after that start preparing all the elements. And stick a double-sided adhesive tape on the template.

20

21

22

When the parts are prepared, all the plates are assembled by marking with adhesive tape, gluing 5 hexagons and bars in the joints. In addition, press the frame with a vice. After drying, carefully separate the platform from the template.

23

24

25

To fix the bars on the outer edge with self-tapping screws fence posts.

26th

The rails are glued to them.

27th

28

Turn the upper part of the mill and attach to it the scaffold bars of the viewing platform. Install this structure in the grooved grooves of the base and press it down with a load.

29

Dome

This element of the decorative mill is made from a hollow polystyrene hemisphere. The fixing ring and the base have the same outer diameter as the dome.

thirty

In the circle, make a hole in the center. Combining the base with the ring, drill 4 more holes in both parts one above the other for self-tapping screws. Combine the central holes of the circle and the top of the assembled mill, fasten them with a screw.

31

Rotating mechanism

Make two square blanks for the framework .Fold them together, secure with vise and, sliding to one edge, make holes for the size of the existing bearings. Put the parts with a thin side up, drill in two places a label for screws longer than the middle of the hole. Cut these blanks in the middle of the circles. For stability between two parts lay the bars, glue all together, attach to the bar of the platform. On one side, the base rises to a small bar so that the whole mechanism is located, not horizontally, but at an angle. In the platform, make holes in the corners to fasten the mechanism to the mill.

32

How to make a decorative mill with your own hands. Photo

33

34

35

Insert the bearings into the grooves of the holes and fix the second parts of the square blanks with screws.

37

Stainless steel pin in both bearings, fasten with washers and nuts.

38

39

To make the mill neatly, to accurately mark the hole for the stud in the dome, the assembled mechanism is installed inside the ring, and the hemisphere is one edge on the hoop, and the opposite one - exactly at the same height. In the place where the hairpin rests against a semicircle - make a mark and then a hole.

40

The dome is glued together with a ring, fastened with adhesive tape.

41

The mechanism is screwed to the round base of the mill and the hemisphere is put on.

42

The dome is fixed in four places with screws.

43

We fix the blades

For a central fastening, a wide square bar of 40 mm thickness, on which the circle is made, is suitable. Having deviated from the edges a quarter of the length of the side, in the center, drill four non-through holes with a large drill. On the reverse side of the round nozzle, make a notch with a diameter of 30 mm. A drill equal to the thickness of the pin of the mechanism should be drilled in the center of the hole. In the sides, make one hole in the middle. Give the finished part a round shape.

44

45

46

47

By pattern cut 4 blades , the size of the mill depends on their dimensions.

48

49

For each wing prepare one frame bar, make a hole in the end, in which to fix the pin with a screw thread or bolt. On the other hand, glue the blade to the bar.

50

51

52

Insert the retainers into the large holes on the bracket, screw the blades into them, secure them with nuts and washers.

53

54

55

Assemble the assembled structure onto the stud of the mill.

56

57

58

The following modification of the wind turbine is designed much easier, but it looks no less attractive.

"Quick" mill, lined with clapboard: step by step instruction with photo

Prepare two square parts for the skeleton: the upper with a side of 300 mm, the base - 400 mm. These blanks, like the whole skeleton, will be trimmed from the top with a lining, so for their manufacture, you can use chipboard sheets or plywood from old furniture or other used materials. Make holes in the center of both parts.

melnica_foto

For accuracy of assembly between the two bases, a rail with a length of about 600 mm is installed, which is screwed with screws to both squares through the central holes. Then the length of the side edges of the trapezoid is measured, the slats of the required length are cut. They are screwed with screws to both bases - the frame is ready.

melnica_foto2

For a roof two isosceles triangular preparations are made, their sizes choose to your taste. Between the parts are set rails of the required length. They are attached to the triangles using self-tapping screws. In the lower part of the roof, be sure to nail a pair of rails in the center to connect to the body. The mill size in the finished form will be about one meter without taking into account the wings.

melnica_foto3

Sew the lower part of the frame with the lining. The measured part is nailed with special nails to the slats, or you mark the hole in the right place with a drill and screw it with screws.

melnica_foto4

Triangles of the roof are lined with a lining in the vertical direction - this looks better. Then the roof is screwed to the body. More interestingly, such a mill will look with windows and a door, which are cut with a jigsaw in the shell.

melnica_foto5

In the center of the roof triangle make a hole in which to insert the pancake bolt. Secure it with two washers and a nut. The roof is closed with a lining, and all corner joints are covered with a decorative corner strip. melnica_foto6

How will the blades of the finished mill look like - a matter of taste and imagination of everyone. In this project they are made of pieces of wooden slats, shot down by small finishing nails. A hole is made in the center of the two bearing strips and they are screwed onto the bolt, fastened with a nut and two washers.

melnica_foto7

A simple decorative mill with your own hands. Photo

Cover the structure with a varnish, and it is ready for installation.

melnica_foto8

Step-by-step instruction with photo how to make a hexahedral frame-frame for a garden.

This spectacular and extremely beautiful ornament for the garden is made of materials that are always found in the building store. But the quality and attractiveness of it depends on the skill, patience and imagination of the master.

decorative mill with own hands

Decorative windmill with own hands. Photo step-by-step

The lower part is made of shanks of shovel .The recesses can be made using a circular saw or special cylindrical nozzles on a drill. For the hexagonal version, they should be made at an angle of 600, and for this you will need an angle of 300 and a special fastener for two cuttings at a time.

You can fasten the finished "logs" to glue or to put on the studs for reliability. To do this, in each connection of the two blanks, a hole is drilled, and they insert a metal rod.

Tip! The windows and doors are more convenient to do in more than two details.

decorative mill with own hands1 decorative mill with own hands2 decorative mill with own hands3 decorative mill with own hands4 decorative mill with own hands5 decorative mill with own hands6

Step-by-step instruction on how to make a decorative mill

The hexagonal workpiece with the studs fixed on it serves as the basis. The first row is the details embroidered along the halves. When the bottom frame is assembled completely it is worth treating it with impregnation or varnish.

decorative mill with own hands7 decorative mill with own hands8

A hexagonal base for the next level is installed on the studs. The ends of the studs are fitted with furniture corners for the carcass rails and the whole structure is clamped with stops. To the base of the frame it is better to immediately attach decorative stable heavy legs from oak.

decorative mill with own hands9

The rails of the second tier are screwed to the furniture corners in the lower part, and above - to the hexagonal base of the next level. This floor of the decorative mill is covered with by rails, and the joints are closed by with decorative slats.

Tip! As often as possible and from all sides, cover the assembled structure with varnish and impregnation - the mill will still stand on the street.

decorative mill with own hands10 decorative mill with own hands11

A rectangular or square base for the roof is installed on the upper hexagon of the second tier. It is fastened to the roof frame: two triangular parts joined together by slats. The roof is trimmed with a beak, and the butt ends are made with smaller chopsticks for sushi. Connections are hidden under decorative slats.

decorative mill by own hands12 decorative mill by own hands13

The axis of the blades passes through the ends of the roof through and through, these holes serve as stops for it. It is made of cuttings for chopping. As the plugs, the ends of the cuttings, mounted on the axis, are used.

For the landing of the blades on the axle a thick bar, cut in the shape of an octahedron, was used. At four ends, holes are made for fixing the wings.

Tip! To rotate the blades and serve for a long time, it is important to make them light, about one weight, of durable material.

To make the design of the wings the same and accurate, it is better to make a template. Straps are fastened to three bars: two lateral and central, turned at the base for the size of the hole in the octagonal mount. The laths for the blades are the dismantled shutter door with perfectly matched and processed slats. They are glued to the frame.

The wings of the frame are to be inserted into the fastening and to make the balancing - inserting them deeper into the groove or vice versa slightly pulling out. They need to be installed slightly at an angle to the plane so that they catch the wind.

Tip! To make the mill correctly, it is necessary to center the blades. They do not fall under the weight of one of them down and easily rotate.

decorative mill by own hands14

Other original design projects for wind turbines

Taking as a basis one of the presented master classes or drawing interesting ideas in all three, you can make an original and decoration - a decorative mill for the garden with your own hands.

The presented design of the finished product is not suitable for your site or you do not like it personally? Look at the selection of the most interesting windmills for the garden and the garden.

Classic version of West European mills decoration. It is best for a lawn, decorated in the traditional Scandinavian, French, German spirit. The first two master classes are taken as a basis, the form of the roof and wings is being finalized.

1

Photo of the decorative mill in the garden

The basis for this design option will be the first project, and interesting details - the roof, covered with soft tiles, and the wind vane of the windmill. It would be original to make the top part of the roof movable and rotating in the wind.

2

Photo of the decorative mill in the garden

Two in one - combine game house for children and decorative landscape mill. To build such a capital structure, it is necessary to get to know more closely the design and construction of non-residential premises.

Mill for your arms_for_down_002-768x1024

Photo of the decorative mill in the garden

A simpler, but very juicy and colorful version of the first master class. Ideal for a bright flower garden or garden. We'll just have to figure out how to make the platform-base.

3

The base of this mill is octagonal. Unlike hexagonal it is easier to make, and as a material for plating fit both plywood and a more relief lining.

4

Photo of the decorative mill in the garden

Spectacular model with a roof trimmed with soft tiles , luxurious trim made of wooden slats and decorative cornice. Beautiful solid blades for the mill are attached to the crosspiece and the accuracy of this particular part is very important for balancing.

5

The upper part of these three windmills is designed as of a small house of superstructure, due to this the construction becomes collapsible. But the frame can serve anything. .. even an old metal tank.

6th

Photo of a decorative mill in the garden of

Simple and uncomplicated. The metal windmill will delight you with dynamic movement in windy weather. Especially if you paint the blades with an interesting pattern.

7th

Powerful ancient stone structure , as if built by ancient Germans or Saxons. If you want to shock neighbors and acquaintances and make children happy - this is exactly such a model.

8

Another interesting model, bsitaya decorative planks .The principle of creation is the same as in the second master class and it can very well be made of high-quality lining. The main thing is to carefully and accurately make the details and choose a deep and elegant color.

I

Photo of the decorative mill in the garden with your own hands

Beautiful wind turbine from the slats in many respects repeats the project from the lining. You decide which material and design you prefer.

It's not so difficult to make a decorative wood mill yourself, as it seems, and not as easy as we would like. Especially if you want the blades to rotate in the wind. But the garden with it becomes unspeakably beautiful, cozy, nice and picturesque.

Content of the article:

  • 1 Decorative mill for the garden with your own hands. Step-by-step instruction
  • 2 "Fast" mill, lined with clapboard: step-by-step instruction with photo
  • 3 Step-by-step instruction with photo how to make a hexahedral frame-mill for a garden.
  • 4 Other original design designs of wind turbines

Mill_for_the_handles_for_the_feed_034-650x433

After spending not much time, you can make this beauty yourself.

We offer you three step-by-step instructions with a photo on the manufacture of windmills of various complexity and several ideas for the design and construction of the finished structure.

Decorative mill for the garden with your own hands. Step-by-step instruction

You will need: plywood, bars of various thickness, wooden slats, glue, adhesive tape, long hairpin, 4 short pins, 4 locks, nuts, gaskets, screws.

The topmost block of the

Cut 6 long trapezoidal blanks by cutting the edge at an angle of 45 º .

1

2

Fold them side-by-side tightly, so that grooves are formed from the underside of the joints. Securely fix all six parts with adhesive tape from the front side.

3

Decorative windmill with own hands. Step-by-step photos

Turn the part and fill the grooves with a reliable with glue, apply the compound and on the side edges of the structure. Do everything quickly until the mixture hardens.

4

Fold the extreme parts and assemble the entire structure, fix it with adhesive tape and leave until it is completely set.

5

Cut the excess glue so that it does not affect the assembly accuracy of the finished structure.

6th

Decorative mill for the garden with your own hands. Photo

Saw the hexagonal cover to the dimensions of the inside of the top of the structure. In the center, drill a hole and screw in the small screw for the convenience of installation.

Turn the frame of the mill, set to the narrow part. Apply glue from the wrong side of the top of the tower, insert the lid, put a small load.

7th

8

I

Base of the upper part of the

This block with the lower parts will be connected using the of the bar-axis in the size 70x70 mm. Make two hexagonal blanks with the side dimension equal to the length of the inner edge of the tower base.

10

In the bottom lid make a square slit in the size of the bar - 70x70 mm, and in the upper - in the center to drill a small hole-mark for the subsequent connection with the axial part.

To the two covers to cut the sides - the wall 6 pieces. Their width is equal to the length of the outer edge of the base of the upper part. The side cuts of the workpieces should be made at an angle of 45 º .

Fold 3 details of the sides of the face to the side, connect the front side with adhesive tape. Apply glue to the grooves on the back of these bonded workpieces and on three sides of the six both covers. Connect the elements of the upper and lower bases to three walls. In addition, fasten with screws and vice. In the same way, attach the remaining faces.

eleven

When the block design is ready to insert into the bottom of the axle bar and connect it to the top cover with a screw through the previously made hole.

12

Lower block to be installed vertically and glued it to the top, setting the load on top.

13

ready structure .

14

instagram viewer