Self-repairing the shower switch

In the functioning of the bathroom,soul, which anyone can handle, having a standard set of tools. The most common problem here is leakage. To eliminate it you need to know its structure and types. The process of the switch in the mixer differs from the type: they are spool, cork, cartridge and push-button.

The device consists of the following components:

• Enclosure;
• Sidewall;
• Supply pipes;
• Spill;
• Spare nut;
• Sleeve;
• Cone.

shower switch device Diagnosing a fault in the

switch If a shower switch repair is required, this can be understood without difficulty. In most cases, it will inevitably leak, but this does not mean that the cause is always the same. The reasons can be as follows:

• Single lever mixer leak;
• Button seizing;Simultaneous water supply to the shower and main tap;
• Weak water head;
• Leak inside the water control mechanism.

In the case where the mixer device is familiar to the master, the true cause of the breakdown can be found quickly.

It should be noted that when the repair of the shower switch is to be done very carefully, the tools are used only to tighten the nuts, the rest is best done manually, so as not to overtighten the details and not spoil everything at all.

Replacing the cartridge of the shower switch

If the bathroom has a standard single-lever mixer, then most likely the cause of the problem is the internal cartridge. It mixes different streams of water in the process of work. It is not subject to repair, a new one will be needed. When buying, be sure to know the diameter and length of the stock.

Stages of repair work:

• Removal of decorative cover;
• Use a hexagon or a standard screwdriver to remove the fixing screw;
• The lever is released;
• The nut fixing the cartridge in the mixer is twisted;
• The old one is pulled out and a new one is installed;
• With attention the mechanism is going back.

Replacement of the sealing rings of the shower switch

Currently, the most popular is the push button switch. But, it has one small drawback: the periodic leakage of water due to the rapidly deteriorating rubber sealing rings. There are two options for repairing the mixer pushbutton: installing a new kit or cleaning and softening the old one.

Widget from SocialMart

To change the rings you need:

• Dismount button;
• Use a wrench to unscrew the entire device;
• Pull out the stem, remove the old ones and install new O-rings;
• Carefully assemble the mixer back.

If the rings are not worn too much or the new kit is long to wait, then they can be softened with a standard solvent or gasoline. But, you need to know that not all materials are amenable to their impact, so 100% of the result can not wait.

shower switch rings look like How to replace the shower switch

There is one more reason why the pushbutton switch can fail during operation: a spring failure. Repair it is not subject, only replacement. Required:

• Remove, shower and shower hose;
• Remove the adapter itself;
• Unscrew plug and fixing screw;
• Take out the stem with the old spring;
• Remove old, install new operating spring;
• Carefully collect back.

Solving other problems with the

shower switch Few people are pleased with the weak water pressure. The main reason for this is a dirty aerator. This device is installed in the place of the spout. The fault can easily be removed with a thorough cleaning.

There are times when a bad pressure of water happens because of its simultaneous feeding in both the shower and the gander. Most often this problem occurs in the spool types. The reason is the unsuitable operation of gaskets and O-rings. To solve the malfunction, the procedure is as follows:

• Remove the handle. In some types of mixers they are simply removed, in others it is necessary to unscrew the fixing screw;
• Change the old gasket to a new one. At the same time check the condition of the sealing rings, if necessary, also change;
• Assemble the mixer.

Recommendations for the repair of the shower mixer switch

Any switch with a shower on the faucet must be of high quality and certified. You should not save on such things. Then the repairs do not have to be done often. It is also recommended to carefully handle the plumbing and to carry out preventive measures.

If a failed sealing ring and a spring are found, it is not necessary to run to the store. Rings can be made independently from a rubber tube.

Regardless, what a failure happened, still have to disassemble. If there is no certainty that it will be possible to assemble it correctly, look for the instruction, it must be applied to all plumbing.