Why the washing machine does not drain the water, repair

click fraud protection

Washing machine does not drain water
  • Why does not it merge?
  • Drain the water yourself
  • Identify the causes of
  • Filter clogging
  • Fault prevention
  • Other possible problems and repair options

The washing machine in the bathroom is an indispensable assistant in every home. Regardless of how many family members live in the same apartment, dirty laundry by hands has long been erased. This responsibility was assumed by machine-machines. However, any technique is imperfect. Sooner or later, it breaks down, which must be repaired. Most people seek help from experienced professionals. However, many failures can be eliminated on their own. The main thing is to establish their cause. In this article we will discuss why a washing machine can not drain water and how to eliminate this malfunction.

Water in the tank of a washing machine

Why does not it merge?

There are many reasons why water can not drain into the sewer. Conditionally they can be divided into external and internal. To external reasons for the breakdown, it is possible to refer:

  • clogging of sewer pipes and siphon;
  • clogging the drain hose and nozzle.
Clogged washing machine siphon

Internal causes of malfunctions include:

  • foreign objects getting inside the washing machine;
  • filter clogging;
  • pump breakdown;
  • hardware failure caused by improper power supply.
Garbage in the washing machine

Drain the water yourself

The first thing you will need to do in case of a breakdown is to drain the water from it.

There are several ways to do this:

  1. Try to drain the water through a special filter, the which is usually located at the bottom, on the front of the device. Remove the protective cover and unscrew the filter from the socket. You will need to slightly tilt the machine forward and fix it in a stationary position. Under the hole, from which the water will pour out, it is necessary to substitute some basin or other vessel, the volume of which is enough to contain all the water.
  2. Use a hose or tubing to drain the water. It will need to be pushed through either a short drain pipe, the outlet of which is located behind the filter on the front panel of the machine, or through the opening for the main drain hose of the machine located behind the washing machine, is low from the floor.
  3. If the nozzle gets clogged, it will be necessary to clean it, and only then drain it through it. To do this, you will also need to remove the filter first.
Filter Replacement
Emergency water drain hose
The nozzle is clogged

After this you need to visually inspect all the components of the washing machine, find out the cause of the fault and proceed from it further.

Revealing the causes of

First of all it is necessary to understand what exactly the cause of the malfunction is.

Disconnect the washing machine from the mains to avoid the risk of electric shock.

  1. Check the drain hose. Make sure that there are no kinks or creases on it. Perhaps you recently did a reshuffle in the room or purchased some new furniture, and during the installation it was accidentally squeezed something like a drain hose. If the water does not flow out of the hose or flows too slowly, it means that a blockage has formed inside it, which must be cleaned. Also, the cause of the malfunction may be that the hose is at the wrong angle to the sewer inlet.
  2. If problems with the hose were not found, then the next step is to check the condition of the sewer pipes and siphon. If clogging occurs in them, it must also be eliminated. Most often this is done mechanically by means of a special cable.
Check the drain hose
Sewage cleaning by hydrodynamic method

Filter clogging

Perhaps this is the most frequent cause of breakdowns, from which no one is immune. Even if you always carefully shake out all the garbage from the pockets before washing, the filter still gets small villi of woolen and synthetic fabrics, which gradually accumulate, creating a jam for unimpeded penetration of water. This problem is solved quite easily. First you will need to get to the filter itself. On the location of its location, you can find out from the instructions to the device.

In most cases, it is hidden behind a small round or square insert at the bottom on the front panel of the device. However, in some models of washing machines, in order to get to the filter, it will be necessary to remove the lower removable panel, which extends the full width of the device. As a rule, you can remove this panel manually. But sometimes you need some thin small thing like a screwdriver to pick it up.

The filter itself is screwed into the socket and sealed with a special dense rubber gasket. Since the filter is screwed tightly enough, it takes a rough male power to unscrew it.

Before unscrewing the filter, make sure that it is not locked in place with the retaining screw. For your convenience, manufacturers have provided on the filter a special handle, for which it should be unscrewed.

Unscrew the filter
Location of drain filter
Drain the water from the filter

As soon as the filter is wrung out, water rushes to the floor. To this you need to be ready and put some capacity in advance or, in extreme cases, put a large rag that will absorb water.

After the filter has been removed, it must be cleaned of accumulated debris and replaced in its original place. In order not to clean the filter under extreme conditions every time, experts recommend that the filter be cleaned at least every four years.

Blockage in the filter
  • If you have not found any foreign objects or blockage in the filter, then most likely it's in the pump. Look into the hole that formed after the filter was removed. There you will see the impeller of the pump. Try to turn her hand from side to side. If something disturbs her movement, then perhaps some thread or a small piece of cloth is wound on her. It is possible to test the efficiency of the pump in a different way. Just run the washing mode on the washing machine without connecting to water and see if the impeller rotates normally. If you do not manage to release it yourself from garbage and restore it to a working state, you will have to call a repairman.
Pump Faults

Fault prevention

To prevent such breakdowns as rarely as possible, simple precautions should be followed:

  • Carefully select the operating mode of the machine. For different types of fabric, its own washing regime is designed. Also, you can not mix dark, light and colored underwear when washing, you can not wash clothes from different types of fabrics in the same mode. Otherwise, you will not be able to achieve the optimum result of washing.
  • Before loading dirty laundry into the washing machine, always carefully check the contents of the pockets. Any foreign objects can cause a breakdown and cause clogging. In the pockets there is always a lot of garbage collected - different pieces of paper, small parts, coins, etc. All this must be unloaded from them before washing. Having created such a habit, you not only protect the washing machine from possible breakdowns, but, perhaps, someday you will save someone's mobile phone, noshniki or player accidentally forgotten in your pocket.
  • Use only suitable washing powder. For automatic washing machines special detergents are sold, which will extend the life of the device, in contrast to conventional, cheap powders. In addition, during washing, you can also use special water softening agents that prevent the appearance of scale on the heating elements of the device.
  • Never load more laundry into the washing machine than authorized, according to the instructions to it.
  • Use a surge protector to connect the washing machine to electricity. There are small voltage drops in almost every house. In modern household appliances such a moment is always taken into account. However, there is a permissible limit, above which there is an overstrain and the equipment can simply burn. To prevent this, it is always better to use additional protection.
Use of a detergent powder
Trunk filters for washing machines
Electric filter for washing machine

Other possible problems and repair options for

There are two other versions of the fault, which are also quite common, but you can hardly cope with it yourself:

  1. Pump failure. More precisely to establish, because of what it happened, only the master will be able to look inside the washing machine. The pump wears out with time. The more dirty laundry you wash and the more often you start the washing machine, the more likely it is that the pump breaks or wears out. Fix the pump of the washing machine is not. The only option is to replace it with a new one.
  2. A violation in the electronic module of the appliance that controls the washing process. In the most advanced modern models of washing machines, a special digital screen is installed on the front panel, on which a fault code is displayed when a certain malfunction occurs, and also an emergency shutdown system is provided in case of card overheating. However, even in simple models, electronics may malfunction due to a sudden electrical surge. In such cases, only an experienced specialist can help you with repair.
Pump replacement

instagram viewer