How to easily wash plastic window sill of any spots: step by step guide

Unfortunately, even the most careful handling of plastic window sills does not guarantee the absence of stains on it. Cope with ordinary dust is quite simple. But what to do with more stubborn stains?

How to get rid of contaminants from plastic window sills - step by step guide

Step 1. First, a plastic structure to be cleaned from dust. To do this in warm water is dissolved little liquid dish detergent or cleaning powder. The resulting solution was washed with a window sill and wait until it dries.

Step 2. To wash it is important to choose the right cloth. So, if the sill - glossy, then it can only be cleaned with a soft cloth! If the window sill - a rough and ribbed, contamination can be removed by stiff brush or sponge.

Important! In any case, you can not use metal scrapers to clean the surface, iron brushes and other abrasive materials, as they may leave scratches and micro-cracks!

Step 3. In an extreme case, the dirt can be wiped off the dried rubber sponge.

Step 4. If on the window sill had dried glue residue coats and other building materials, they should first soak. To do this directly with the soiled portion is necessary to pour a little hot water. Then, at the expiration of 10-15 min. pollution can scour sponge rubber.

Step 5. Often dirt is collected in the areas between the frame and sill. To remove it, you can use a toothbrush.

Also, to clean the plastic surface it is not recommended to use the acid and aggressive chemicals.

Common types of stains on the plastic window sills:

• yellow water;
• ingrained fat (often found in the kitchen);
• traces of rust;
• frozen remnants of glue, primers and other construction materials that appear as a result of repair work;
• traces of adhesive tape, markers, felt-tip pens, etc.

How to remove various stains with the help of available funds

One possibility of getting rid of the above impurities are specialty chemicals. However, they are not always at hand or have the desired impact. In this case it is better to resort to assistant means.

Yellow stains and traces of rust

Most plain and at the same time effective way to get rid of rust and yellow spots - suds.

On a fine grater grate 50 g. laundry soap. Then stir it in 1 l. hot water. The resulting solution was applied to the contaminated portion and leave 10-15 min. Then gently rub the sponge rubber and wash off with warm water solution.

this old spot

Delete stubborn dirt any origin help a mixture of soda and vinegar. For this 1 tsp soda mixed with 1. tsp vinegar. Then add to the mix 2 tsp water. The resulting formulation is applied to the stain. It's worth noting that keep soda and vinegar on the spot can be no longer than 5 minutes. This is followed by rinse with warm water sill.

Traces of flowerpots

To cope with this kind of pollution can hydrogen peroxide. It should be mixed warm water in proportions 1:1 and the resulting solution wipe contaminated sites. Stubborn stains can be treated with a solution and leave for 5-10 min. Then wipe clean water.

Traces of pens, markers, pens

In this case, you need to take ammonia or rubbing alcohol and dilute it in water in relation to 1:1. Then wipe the stain solution and rinse with warm water windowsill.

If there is no alcohol on hand, you can use the nail polish remover based on acetone. It can also be diluted with water in proportions 1:1.

Stains of various origins

Lemon juice help get rid of a variety of spots, as well as the return to its former whiteness. So, with warm water were mixed in equal proportions fresh lemon juiceor citric acid. Then applied to the composition of the stain and leave for 5-10 min. Then wipe the window sill with clean water.

The bleaching composition

Mel & toothpowder perfectly removes dirt, as well as bleached windowsill. To begin with chalk grind to dust. then take 1 h. l. Cretaceous and add a little water. Mix composition to a paste. Instead of chalk, you can take 1 tsp tooth powder. Apply the paste on the stain, rub her rubber sponge, then wipe clean with warm water.

Spots after repair

First, they need to soften (about 30 min.), And then carefully remove the rubber staple. foam residues, primers and adhesives must scrape rubber sponge. Then clean the spot with the help of any of the above means.

If the glue is strongly ingrained, it should be applied solvent ("White Spirit"). A small amount of solvent impregnated cotton wool, then wipe the contaminated site, and immediately washed with water.

Important! The solvent may leave yellow marks on the windowsill, so deal with it should be cautious.