Stickers with glue

Caviar refers to overhead curly details used in the design of window or door openings.
Pliers are used to close the gaps when installing a door or window box. The installation of clypeus improves the aesthetic appearance not only of the door or window, but also of the room itself.
Platbands are external and internal.

External trim frames are used to decorate door and window openings outside the building.
Internal lining is used for aesthetic design of door, window openings inside the room.
Most often, the internal platbands are fastened with nails. But it is allowed to fasten lightweight casing designs with liquid nails, silicone or foam. It is only necessary to ensure the full fit of the casing to the wall and the door frame.

Any adhesive materials can withstand a certain load, and with a large weight of clypeus can not qualitatively hold the platbands on the plane.

When choosing this or that adhesive composition, specify the weight and properties of the platbands.
You can glue the platbands for liquid nails, but you can fix it on silicone or foam.

Where to start?

In order for the casing to stay firmly in place, they must be properly adjusted and secured. To ensure proper fixing of the platbands, it is necessary to observe the technology and the order of the work.

Preparation of platbands for fastening

Platbands are preliminarily cut, marked. If necessary, one edge is cut at an angle of 45 degrees. Trimming of the platbands is best done with the miter saw or chair.
Reiki are tried on the box and labeled.

And how to glue the platbands for the boxes?
Mounting of platbands with adhesive compounds is possible only if the surface of the wall and the surface of the box lie in the same plane. If there are deviations, the platbands will not fit snugly against the surface, and their gluing is not possible. Have to level the walls with putty.

Widget from SocialMart

Adhesive trim with liquid nails

If you want to learn how to glue the trim for liquid nails, try to purchase the platbands without bends and the right shape.
Plastic trims can be glued to liquid nails, provided that the walls are perfectly even.
Check the flatness of the box for the entire height. Sites where you plan to glue the trim, you need to free it from the wallpaper, clean it, and primer it. As a primer is recommended to use glue PVA.
After the glue dries, apply the liquid nails with the dots in 20 cm steps. The rail is applied to a pre-marked place and held for several minutes. Ideally, clamp the clamp at night. Different manufacturers of liquid nails have their own technological requirements.
Allowed in problem areas, fix the slats using nails which can then be covered with furniture wax.
The strength of the joint to be bonded is influenced in many respects by the properly selected adhesive.
Of the most reliable it is possible to recommend liquid nails under the designation TITE BOND with red letters. And you can also use Titebond glue with the designation Heavy Duty, which allows you to glue heavy parts.
The "Moment" glue does not always provide the required connection quality.

When pressing the casing with the liquid nails applied to the surface, the glue can protrude. In such cases, the adhesive should be removed immediately.

How to glue the trim with the foam

And how to glue the platbands on the door with a mounting foam?
To be honest, it is quite difficult to get a quality joint of clypeus with the wall surface using a mounting foam.
As in the first case, the basic requirement is that the plane of the wall and the door frame be level. Otherwise, ensure the quality fit of the clypeus to the wall will not succeed.
The trim is sewn in the same way as for liquid nails.

It is necessary to apply clamps, which fix the platbands for a sufficiently long time to dry.
For reliable fixing of the casing, it is recommended to use nails, hammering at least two in each clypeus.

Here are tips on how to remove the mounting foam if it fell on your hands or objects.

How to glue the platbands for acrylic sealants or silicone

It is also possible to glue the platbands with silicone, this is a simple and effective way of fastening. There are different types of sealants in different combinations. Light casing can be glued perfectly to a perfectly flat wall and with silicone and do not even need a clamp and nails.

Install the box flush with the wall. Clean the place of application of the adhesive from dust, dirt. Apply a layer of a deep penetration primer.
The platband is applied to the platband in the middle in 10 cm steps. The plat bands are applied to the previously marked place, they are kept for several seconds.

Conclusions:

- silicone, liquid nails, mounting foam can be used to fasten the casing; all methods are good;

- for reliable fixing it is recommended to use a combined method, stick the platbands and fix it with a minimum number of nails, which are then masked with furniture wax.