Drawings of greenhouses from a profile pipe with the sizes: a greenhouse with own hands and a skeleton, self-made calculation and the calculator

You can use ready-made drawings and diagrams shown on the Internet, or, armed with patience, to develop the necessary sketches yourself Correctly composed drawings greenhouses from profile pipe with dimensions - the key to long-term operation of this kind of design. Despite the apparent complexity, even a beginning gardener can cope with the development of the project. Here it is important to focus attention on the fact that the direct assembly of greenhouses from the profile pipe on the basis of a technically correct drawing takes no more than 2-3 hours.

designers to sOutline: homemade greenhouse from the profile pipe

The degree of detailing of the drawing is the most difficult moment in the work. If some say that the technology requires consideration of all objects of the material world present at the site, others - take into account only the welded greenhouse itself. Truth, as often happens, is in the middle.

drawings greenhouses made of polycarbonate with their hands from a profile pipe to help accurately calculate the required number of elements for the construction of

right to make a greenhouse out of the profile pipe will help the rational approach.

Draw can be on the following practical tips:

• account of the position of a source of shade, such as a fence, vegetation, other houses and outbuildings;
• The type of building materials selected is fixed, otherwise the difference in technical parameters will not allow the production of the seedling house to be completed;
• The presence of pipelines and other types of communication facilities in the immediate vicinity of the greenhouse must be recorded in the project.

Technically literate drawing involves accounting for everything that surrounds the greenhouse. At the same time, attention is focused only on the fact that it directly interacts with the greenhouse. Building

greenhouse of a shaped tube with his hands on pegs

To begin carried planarizing where it will set a greenhouse. After this, they are placed with the greatest accuracy around the perimeter of the peg. The interval between them is from 25 to 30 cm. On the basis of these figures it is not difficult to get the required number of them.

to take full advantages of the greenhouse in the garden area, yet at the stage of its design makes sense to pay special attention to the choice of materials for the frame and walls

Once the perimeter of the greenhouse is checked, all the pegs driven into the ground to a depth of 20-25See It is necessary to make sure of the strength of the resulting structure, otherwise the arcs of the base will quickly lose their strength.

In the future, the base is assembled on the basis of the drawing.

The procedure is as follows:

• tees are mounted so that the pipe is free to pass through them;
• Self-tapping screws are used as the main fixing element, which are selected taking into account the pipe dimensions;
• If you do not want to bother with fasteners, then you can use a different method - you should cut the pipe into smaller parts with your own hands;
• Regardless of the method of fixing each tee assembly is further secured with glue, otherwise the frame will not be strong enough;
• The arches and all connecting elements are installed;
• Window and door openings are manufactured in accordance with the approved drawing;
• In order to exclude the likelihood of a draft, it is recommended for the door panel to take a profile with a diameter of 1-1 / 4.

The variety of the greenhouse on the pegs has worked well in temperate climates. At the design stage, you need to specify the position of each of them, otherwise you should not expect reliable fixation of the arches. In addition, a wider( in terms of diameter) pipe profile is taken for the window and entrance groups.

Tips for beginners: greenhouses from the profile pipe with boxes

In the case when the groundwater level in the site is low enough, the greenhouse can be installed on the base of the boards. At the stage of drawing the drawing, measurements are taken of diagonals drawn from 4 points of the base.

The foundation for a greenhouse is the foundation that will ensure the stability, integrity, strength of construction

Calculate the optimal length and width is not very difficult. Construction will be successful only if each corner of the structure is 90 degrees.

Beginners need to remember that the ground is characterized by a slight, but still mobility. To ensure that the fixed dimensions remain unchanged during the manufacturing process, additional reinforcement should be used. It is made from pieces of old reinforcement.

In addition, it is not superfluous to pay attention to the following recommendations:

• In the project, it is necessary to take into account the necessary distance between the arcs - the optimal value is in the range from 0.5 to 1 m;
• Fixers from the old fittings are driven into the ground in such a way that they rise 25-30 cm above the surface;
• Depending on whether it is planned to erect a greenhouse of 20x20 or 40x20 from a profiled pipe, the pipes themselves are cut;
• Each end of such a pipe is fixed at the base with the use of screws;
• Each end requires a wooden frame, in which you need to make a window;
• This is done on the basis of an agreed scheme of work.

The greenhouse project on a wooden base is justified when there is good soil on the plot. To a greater extent, this refers to the level of groundwater, which should be low. In this case, a steel frame is mounted on top of the wooden base. The key to success is the correct calculation of the distance between arched arcs. You can do it yourself, or give preference to an engineering calculator.

Wear-resistant greenhouse frame from a profile pipe: drawings in details

It can often be heard that even a correctly executed project leads to a lot of problems. Opens the list of violations of the geometry of the structure as a result of partial or complete deformation of the metal arched arcs.

The site must be equipped in accordance with the specifics of the structure

On the one hand, the grower took into account the minimum required pipe thickness, but something still went wrong. On the other hand, the wrong calculation is to blame.

The emphasis is on errors related to the incorrect correlation of soil characteristics, planned dimensions of the structure and its weight.

The following recommendations will help to reduce the number of such recommendations:

• The wider the polycarbonate greenhouse, the wider the base;
• Long construction, for example, from 30 m and more, requires welding arched arcs at a distance of at least 1.2 - 1.5 m;
• The presence of two or more self-made pans automatically entails the need for a profile pipe.

Most of the errors occur in the gardeners at the stage of drafting. First, remember that the width and height of the structure directly affects the base. In this regard, it is necessary to carry out several measurements, which make it possible to exclude even the slightest probability of error.

Gardeners share their experience: how to weld a greenhouse of metal profile pipes

For many, it is a real discovery that, regardless of the type of construction, the welding method is taken into account when drawing up the drawing. The diameter of the pipes, the number of supporting arch structures - the two most important parameters that determine the minimum number of points for welding.

It is considered that the profile pipe is the most suitable option for the manufacture of such structures

Recommendations from

1. will help you to solve a number of problems in the welding process. The binding is always fixed on preassembled mortgages at the foundation level. In this case, even an inexperienced welder will not have difficulty.
2. Welding works are performed only until the polycarbonate is applied, otherwise the coating will become unusable. Before you take the welding machine in hand, you need to make sure the fixation of the carcass is correct. It is not superfluous to make sure that the thickness of each profile pipe corresponds to the parameters specified in the previously approved project.
3. After completion of welding, the skeleton should be painted and anti-corrosion treated.

Greenhouse from the profile pipe with your own hands( video)

Even a minor oversight can not be corrected after all the fixing points have been welded. It was the poet who paid most attention, as was said before, to the drawing. The document seems insignificant, although, in fact, it determines the durability of the building by 90%.If the gardener does not feel the strength, you can always use an engineering calculator.